Optimization of silica silanization by 3-aminopropyltriethoxysilane

Engineering the spatial selectivity of surfaces at the nanoscale using particle lithography combined with vapor deposition of organosilanes

Particle lithography is a practical approach to generate millions of organosilane nanostructures on various surfaces, without the need for vacuum environments or expensive instrumentation. This report describes a stepwise chemistry route to prepare organosilane nanostructures and then apply the patterns as a spatially selective foundation to attach gold nanoparticles. Sites with thiol terminal groups were sufficiently small to localize the attachment of clusters of 2-5 nanoparticles. Basic steps such as centrifuging, drying, heating, and rinsing were used to generate arrays of regular nanopatterns. Close-packed films of monodisperse latex spheres can be used as an evaporative mask to spatially direct the placement of nanoscopic amounts of water on surfaces. Vapor phase organosilanes deposit selectively at areas of the surface containing water residues to generate nanostructures with regular thickness, geometry, and periodicity as revealed in atomic force microscopy images. The area of contact underneath the mesospheres is effectively masked for later synthetic steps, providing exquisite control of surface coverage and local chemistry. By judicious selection in designing the terminal groups of organosilanes, surface sites can be engineered at the nanoscale for building more complex structures. The density of the nanopatterns and surface coverage scale predictably with the diameter of the mesoparticle masks. The examples presented definitively illustrate the capabilities of using the chemistry of molecularly thin films of organosilanes to spatially define the selectivity of surfaces at very small size scales.

Aminosilane multilayer formed on a single-crystalline diamond surface with controlled nanoscopic hardness and bioactivity by a wet process

Diamond could be an excellent support for nanodevices utilizing biomolecules if it is covered with a polymer layer immobilizing a variety of biomolecules. We report a wet method to form a 3-aminopropyltriethoxysilane (APTES) multilayer with a controlled hardness, roughness, and capacity for immobilizing protein. The method is feasible in typical biochemical laboratories where biomolecules are prepared. Atomic force microscopy (AFM) revealed that the surface geometries and nanoscopic hardness of the multilayers on an oxygen-terminated single-crystalline diamond surface depended on the dielectric constant of the solvent; the smaller the constant, the harder the layer. The hard multilayers had holes and APTES aggregates on the surfaces, while less hard ones had homogeneous surfaces with rare holes and little aggregates. The secondary deposition of APTES in a solvent with a large dielectric constant on a hard multilayer removed the holes, and further treatment of the multilayer in acidic ethanol solution diminished the aggregates. Such a surface can immobilize streptavidin with enough specificity against nonspecific adsorption using a combination of polyethylene glycol reagents. The results of a scratching test and nanoindentation test with AFM provided consistent results, suggesting some universality of the scratching test independent of the tip structure of the cantilever. The mechanism of formation of multilayers on the diamond surface and their binding to it is discussed.

Langmuir adsorption study of the interaction of CdSe/ZnS quantum dots with model substrates: influence of substrate surface chemistry and pH

We investigate the utility of Langmuir adsorption measurements for characterizing nanoparticle-substrate interactions. Spherical CdSe/ZnS core-shell nanoparticles were chosen as representative particles because of their widespread use in biological labeling measurements and their relatively monodisperse dimensions. In particular, the quantum dots were functionalized with 11-mercaptoundecanoic acid, and we utilized an amine-terminated self-assembled monolayer (SAM) as a model substrate. SAMs with different end-groups (-CH(3) and -COOH) were also considered to contrast with the adsorption behavior on the amine-terminated SAM substrates. We followed the kinetics of nanoparticle adsorption on the aminosilane layer by quartz crystal microgravimetry (QCM) over a range of particle concentrations and determined the corresponding Langmuir adsorption isotherms. Analysis of both equilibrium adsorption and kinetic adsorption data allowed us to determine a consistent value of the Langmuir adsorption equilibrium constant for the amine-terminated SAM at room temperature (K(L) approximately 2.7 (micromol/L)(-1)), providing a useful characterization of the nanoparticle-substrate interaction. The effect of varying solution pH on Langmuir adsorption was also investigated in order to gain insight into the role of electrostatic interactions on nanoparticle adsorption. The equilibrium extent of adsorption was found to be maximum at about pH 7. These changes of nanoparticle adsorption were further quantified and validated by X-ray photoelectron spectroscopy (XPS) and confocal fluorescence microscopy measurements. We conclude that Langmuir adsorption measurements provide a promising approach for quantifying nanoparticle-substrate interactions.

Chemical strategies for generating protein biochips

Protein biochips are at the heart of many medical and bioanalytical applications. Increasing interest has been focused on surface activation and subsequent functionalization strategies for immobilizing these biomolecules. Different approaches using covalent and noncovalent chemistry are reviewed; particular emphasis is placed on the chemical specificity of protein attachment and on retention of protein function. Strategies for creating protein patterns (as opposed to protein arrays) are also outlined. An outlook on promising and challenging future directions for protein biochip research and applications is also offered.

Attachment of 3-(Aminopropyl)triethoxysilane on silicon oxide surfaces: dependence on solution temperature

Parameters important to the self-assembly of 3-(aminopropyl)triethoxysilane (APTES) on chemically grown silicon oxide (SiO 2) to form an aminopropyl silane (APS) film have been investigated using in situ infrared (IR) absorption spectroscopy. Preannealing to approximately 70 degrees C produces significant improvements in the quality of the film: the APS film is denser, and the Si-O-Si bonds between the molecules and the SiO 2 surface are more structured and ordered with only a limited number of remaining unreacted ethoxy groups. In contrast, post-annealing the functionalized SiO 2 samples after room temperature reaction with APTES (i.e., ex situ annealing) does not lead to any spectral change, suggesting that post-annealing has no strong effect on the horizontal polymerization as suggested earlier. Both IR and ellipsometry data show that the higher the solution temperature, the denser and thinner the APS layer is for a given immersion time. Finally, the APS layer obtained by preannealing the solution at 70 degrees C exhibits a better stability in deionized water than the APS layer prepared at room temperature.

How to prevent the loss of surface functionality derived from aminosilanes

Aminosilanes are common coupling agents used to functionalize silica surfaces. A major problem in applications of 3-aminopropylsilane-functionalized silica surfaces in aqueous media was encountered: the loss of covalently attached silane layers upon exposure to water at 40 degrees C. This is attributed to siloxane bond hydrolysis catalyzed by the amine functionality. To address the issue of loss of surface functionality and to find conditions where hydrolytically stable amine-functionalized surfaces can be prepared, silanization with different types of aminosilanes was carried out. Hydrolytic stability of the resulting silane-derived layers was examined as a function of reaction conditions and the structural features of the aminosilanes. Silane layers prepared in anhydrous toluene at elevated temperature are denser and exhibit greater hydrolytic stability than those prepared in the vapor phase at elevated temperature or in toluene at room temperature. Extensive loss of surface functionality was observed in all 3-aminopropylalkoxysilane-derived layers, independent of the number and the nature of the alkoxy groups. The hydrolytic stability of aminosilane monolayers derived from N-(6-aminohexyl)aminomethyltriethoxysilane (AHAMTES) indicates that the amine-catalyzed detachment can be minimized by controlling the length of the alkyl linker in aminosilanes.

Molecular Recognition and Specific Interactions for Biosensing Applications

Molecular recognition and specific interactions are reliable and versatile routes for site-specific and well-oriented immobilization of functional biomolecules on surfaces. The control of surface properties via the molecular recognition and specific interactions at the nanoscale is a key element for the nanofabrication of biosensors with high sensitivity and specificity. This review intends to provide a comprehensive understanding of the molecular recognition- and specific interaction-mediated biosensor fabrication routes that leads to biosensors with well-ordered and controlled structures on both nanopatterned surfaces and nanomaterials. Herein self-assembly of the biomolecules via the molecular recognition and specific interactions on nanoscaled surfaces as well as nanofabrication techniques of the biomolecules for biosensor architecture are discussed. We also describe the detection of molecular recognition- and specific interaction-mediated molecular binding as well as advantages of nanoscale detection.

Organic functionalization of luminescent oxide nanoparticles toward their application as biological probes

Luminescent inorganic nanoparticles are now widely studied for their applications as biological probes for in vitro or in vivo experiments. The functionalization of the particles is a key step toward these applications, since it determines the control of the coupling between the particles and the biological species of interest. This paper is devoted to the case of rare earth doped oxide nanoparticles and their functionalization through their surface encapsulation with a functional polysiloxane shell. The first step of the process is the adsorption of silicate ions that will act as a primary layer for the further surface polymerization of the silane, either aminopropyltriethoxysilane (APTES) or glycidoxypropyltrimethoxysilane (GPTMS). The amino- or epoxy- functions born by the silane allow the versatile coupling of the particles with bio-organic species following the chemistry that is commonly used in biochips. Special attention is paid to the careful characterization of each step of the functionalization process, especially concerning the average number of organic functions that are available for the final coupling of the particles with proteins. The surface density of amino or epoxy functions was found to be 0.4 and 1.9 functions per square nanometer for GPTMS and APTES silanized particles, respectively. An example of application of the amino-functionalized particles is given for the coupling with alpha-bungarotoxins. The average number (up to 8) and the distribution of the number of proteins per particle are given, showing the potentialities of the functionalization process for the labeling of biological species.

Immobilization of functional light antenna structures derived from the filamentous green bacterium Chloroflexus aurantiacus

The integration of highly efficient, natural photosynthetic light antenna structures into engineered systems while their biophotonic capabilities are maintained has been an elusive goal in the design of biohybrid photonic devices. In this study, we report a novel technique to covalently immobilize nanoscaled bacterial light antenna structures known as chlorosomes from Chloroflexus aurantiacus on both conductive and nonconductive glass while their energy transducing functionality was maintained. Chlorosomes without their reaction centers (RCs) were covalently immobilized on 3-aminoproyltriethoxysilane (APTES) treated surfaces using a glutaraldehyde linker. AFM techniques verified that the chlorosomes maintained their native ellipsoidal ultrastructure upon immobilization. Results from absorbance and fluorescence spectral analysis (where the Stokes shift to 808/810 nm was observed upon 470 nm blue light excitation) in conjunction with confocal microscopy confirm that the functional integrity of immobilized chlorosomes was also preserved. In addition, experiments with electrochemical impedance spectroscopy (EIS) suggested that the presence of chlorosomes in the electrical double layer of the electrode enhanced the electron transfer capacity of the electrochemical cell. Further, chronoamperometric studies suggested that the reduced form of the Bchl- c pigments found within the chlorosome modulate the conduction properties of the electrochemical cell, where the oxidized form of Bchl- c pigments impeded any current transduction at a bias of 0.4 V within the electrochemical cell. The results therefore demonstrate that the intact chlorosomes can be successfully immobilized while their biophotonic transduction capabilities are preserved through the immobilization process. These findings indicate that it is feasible to design biophotonic devices incorporating fully functional light antenna structures, which may offer significant performance enhancements to current silicon-based photonic devices for diverse technological applications ranging from CCD devices used in retinal implants to terrestrial and space fuel cell applications.

Multifunctional silane polymers for persistent surface derivatization and their antimicrobial properties

We demonstrate a versatile methodology combining both covalent surface anchoring and polymer cross-linking that is capable of forming long-lasting coatings on reactive and nonreactive surfaces. Polymers containing reactive methoxysilane groups form strong Si-O-Si links to oxide surfaces, thereby anchoring the polymer chains at multiple points. The interchain cross-linking of the methoxysilane groups provides additional durability to the coating and makes the coatings highly resistant to solvents. By tailoring the chemical structure of the polymer, we were able to control the surface energy (wetting) of a variety of surfaces over a wide range of water contact angles of 30-140 degrees . In addition, we synthesized covalently linked layer-by-layer polymeric assemblies from these novel methoxysilane polymers. Finally, antibacterial agents, such as silver bromide nanoparticles and triiodide ions, were introduced into these functional polymers to generate long-lasting and renewable antiseptic coatings on glass, metals, and textiles.

Functional PEG-modified thin films for biological detection

We report a general procedure to prepare functional organic thin films for biological assays on oxide surfaces. Silica surfaces were functionalized by self-assembly of an amine-terminated silane film using both vapor- and solution-phase deposition of 3'-aminopropylmethyldiethoxysilane (APMDES). We found that vapor-phase deposition of APMDES under reduced pressure produced the highest quality monolayer films with uniform surface coverage, as determined by atomic force microscopy (AFM), ellipsometry, and contact angle measurements. The amine-terminated films were chemically modified with a mixture of carboxylic acid-terminated poly(ethylene glycol) (PEG) chains of varying functionality. A fraction of the PEG chains (0.1-10 mol %) terminated in biotin, which produced a surface with an affinity toward streptavidin. When used in pseudo-sandwich assays on waveguide platforms for the detection of Bacillus anthracis protective antigen (PA), these functional PEG surfaces significantly reduced nonspecific binding to the waveguide surface while allowing for highly specific binding. Detection of PA was used to validate these films for sensing applications in both buffer and complex media. Ultimately, these results represent a step toward the realization of a robust, reusable, and autonomous biosensor.

Morphology and amine accessibility of (3-aminopropyl) triethoxysilane films on glass surfaces

3-Aminopropyl) triethoxysilane (APTES) is commonly used to functionalize glass substrates because it can form an amine-reactive film that is tightly attached to the surface. In this study, we investigated the morphology and chemical reactivity of APTES films prepared on glass substrates using common deposition techniques. Films were prepared using concentrated vapor-phase deposition, dilute vapor-phase deposition, anhydrous organic-phase deposition and aqueous-phase deposition. All films were annealed, or cured, at 150 degrees C. The morphology of the films was quantified by fluorescence and by atomic force microscopy (AFM). The optical equivalent of the AFM images was computed and then used to directly compare optical and AFM images. Reactive amine density was determined by a picric acid assay and by a method that employed N-succinimidyl 3-[2-pyridyldithio]-propionamido (SPDP) cross-linked rhodamine. Fluorescence and AFM images showed that silane films prepared from dilute vapor-phase and aqueous-phase deposition were more uniform and had fewer domains than those deposited by the other methods. The ratio of picric acid-accessible amino groups to SPDP cross-linked rhodamine-accessible groups varied with the preparation method, suggesting reactant size-dependent difference in amine accessibility. We found a larger number of accessible amino groups on films prepared by vapor-phase deposition than on those prepared from solution deposition. The dilute vapor-phase deposition technique produced relatively few domains, and it should be a good choice for bioconjugation applications. There were appreciable differences in the films produced by each method. We suggest that these differences originate from differences in film rearrangement during annealing.

Patterned when wet: environment-dependent multifunctional patterns within amphiphilic colloidal crystals

A simple integration of molecular and colloidal self-assembly approaches with photopatterning is shown to produce multifunctional patterns of amphiphilic colloidal crystals. These crystals display binary spatial patterns of wettability by water and a single photonic stop-band in air. Upon exposure to water, the uniform stop-band is replaced by a pattern of coexisting stop-bands that reflect the underlying pattern of surface wetting. These hydration-dependent photonic patterns within single colloidal crystals form because of near-complete water rejection from the three-dimensionally disposed nanoscale interstices in hydrophobic regions and its exclusive permeation within the hydrophilic regions. This water permeation pattern is further structured by the three-dimensional (3D) distribution and contiguity of the nanoscale interstices between individual colloids, allowing 3D patterned organization of functional units in secondary self-assembly processes, as illustrated using quantum dots, metal nanoparticles, and fluorescent probes.

Highly ordered nanowire arrays on plastic substrates for ultrasensitive flexible chemical sensors

The development of a robust method for integrating high-performance semiconductors on flexible plastics could enable exciting avenues in fundamental research and novel applications. One area of vital relevance is chemical and biological sensing, which if implemented on biocompatible substrates, could yield breakthroughs in implantable or wearable monitoring systems. Semiconducting nanowires (and nanotubes) are particularly sensitive chemical sensors because of their high surface-to-volume ratios. Here, we present a scalable and parallel process for transferring hundreds of pre-aligned silicon nanowires onto plastic to yield highly ordered films for low-power sensor chips. The nanowires are excellent field-effect transistors, and, as sensors, exhibit parts-per-billion sensitivity to NO2, a hazardous pollutant. We also use SiO2 surface chemistries to construct a 'nano-electronic nose' library, which can distinguish acetone and hexane vapours via distributed responses. The excellent sensing performance coupled with bendable plastic could open up opportunities in portable, wearable or even implantable sensors.