Bone-bonding behavior of alumina bead composite

AKILE™ total ankle arthroplasty: Clinical and CT scan analysis of periprosthetic cysts

INTRODUCTION

Despite good clinical results following total ankle replacement (TAR), the development of large periprosthetic cysts (>400 mm(2)) in the medium-term is a source of concern.

OBJECTIVE

The primary objective of this study was to detect any large periprosthetic cysts in a cohort of AKILE™ patients using radiographs and CT scans, and then to compare these findings to published ones.

MATERIAL AND METHODS

A total of 127 TAR procedures were performed between June 1995 and January 2012. We retrospectively reviewed 68 cases with the newest AKILE™ implant design that had a minimum follow-up of 36 months. The average follow-up was 81 ± 33 months; eight patients were lost to follow-up. The outcomes consisted of analyzing radiographs (A/P and lateral weight bearing views, Meary view and lateral views of flexion/extension) and helical CT scans, performing clinical evaluations (range of motion, AOFAS score, Foot Function Index, pain levels) and determining the survivorship of TAR implants.

RESULTS

TAR survival at 5 years was 79% for in situ implants and 62% for revision-free implants. The AOFAS score improved from 33.7 ± 14.7 to 77.1 ± 15.1 (out of 100) and the pain sub-score was 30.2 ± 9.7 (out of 40) at the last follow-up. The average ankle range of motion was 32.3° ± 12.7° on the radiographs. CT scan revealed Type A cysts (<200 mm(2)) under the talar implant in 52% of cases and in the tibia in 50% of cases; these cysts were smaller than 100 mm(2) in 80% of cases and had no effect on the implants. No periprosthetic cysts larger than 400 mm(2) in size were identified.

DISCUSSION

The medium-term functional results and survivorship are comparable to those reported for other TAR designs. The incidence of cysts was low overall and there were no large-diameter cysts, which should improve long-term survival. The implant's design and materials likely played a role in preserving the periprosthetic bone stock. The AKILE™ TAR has distinctive features related to the low rate of large periprosthetic cysts in the medium-term.

LEVEL OF EVIDENCE

IV (retrospective case series).

Adsorption characteristics of bovine serum albumin onto alumina with a specific crystalline structure

Bone cement containing alumina particles with a specific crystalline structure exhibits the ability to bond with bone. These particles (AL-P) are mainly composed of delta-type alumina (δ-Al2O3). It is likely that some of the proteins present in the body environment are adsorbed onto the cement and influence the expression of its bioactivity. However, the effect that this adsorption of proteins has on the bone-bonding mechanism of bone cement has not yet been elucidated. In this study, we investigated the characteristics of the adsorption of bovine serum albumin (BSA) onto AL-P and compared them with those of its adsorption onto hydroxyapatite (HA), which also exhibits bone-bonding ability, as well as with those of adsorption onto alpha-type alumina (α-Al2O3), which does not bond with bone. The adsorption characteristics of BSA onto AL-P were very different from those onto α-Al2O3 but quite similar to those onto HA. It is speculated that BSA is adsorbed onto AL-P and HA by interionic interactions, while it is adsorbed onto α-Al2O3 by electrostatic attraction. The results suggest that the specific adsorption of albumin onto implant materials might play a role in the expression of the bone-bonding abilities of the materials.

High modulus nanopowder reinforced dimethacrylate matrix composites for dental cement applications

Results from the study of a novel, high modulus nanopowder filled resin composite are presented. This composite is developed to serve (1) as a high stiffness support to all-ceramic crowns and (2) as a means of joining independently fabricated crown core and veneer layers. Nanosized Al(2)O(3) (average particle size 47 nm) reinforcement provides stiffness across joins. Two systems are examined: Al(2)O(3) with 50:50 bis-GMA:TEGDMA monomers (ALBT) and Al(2)O(3) with pure TEGDMA (ALT). To obtain higher filler levels, surfactant is used to aid mixing and increase maximum weight percent of nanopowder filler from 72 to 80. The loading level of Al(2)O(3) has significant effects on composite properties. The elastic modulus for cured ALBT systems increases from 4.6 GPa (0 wt % filler) to 29.2 GPa (80 wt % filler). The elastic modulus for cured ALT systems increases from 3.0 GPa (0 wt % filler) to 22.9 GPa (80 wt % filler). Similarly, ALBT hardness increases from 200 MPa (0% filler) to 949 MPa (80 wt % filler), and ALT hardness increases from 93 MPa (0% filler) to 760 MPa (80 wt % filler). Our results indicate that with a generally monodispersed nanosized high modulus filler relatively high elastic modulus resin based composite cements are possible.

In vivo aging test for a bioactive bone cement consisting of glass bead filler and PMMA matrix

The degradation of a new bioactive bone cement (GBC), comprised of an inorganic filler (bioactive MgO-CaO-SiO(2)-P(2)O(5)-CaF(2) glass beads) and an organic matrix [high-molecular-weight polymethyl methacrylate (PMMA)], was evaluated in an in vivo aging test. Hardened rectangular specimens (20 x 4 x 3 mm) were prepared from two GBC formulations (containing 50% w/w [GBC50] or 60% w/w [GBC60] bioactive beads) and a conventional PMMA bone cement control (CMW-1). Initial bending strengths were measured with the use of the three-point bending method. Specimens of all three cements were then implanted into the dorsal subcutaneous tissue of rats, removed after 3, 6, or 12 months, and tested for bending strength. The bending strengths (MPa) of GBC50 at baseline (0 months), 3, 6, and 12 months were 136 +/- 1, 119 +/- 3, 106 +/- 5 and 104 +/- 5, respectively. Corresponding values were 138 +/- 3, 120 +/- 3, 110 +/- 2 and 109 +/- 5 for GBC60, and 106 +/- 5, 97 +/- 5, 92 +/- 4 and 88 +/- 4 for CMW-1. Although the bending strengths of all three cements decreased significantly from 0 to 6 months, those of GBC50 and GBC60 did not change significantly thereafter, whereas that of CMW-1 declined significantly between 6 and 12 months. Thus, degradation of GBC50 and GBC60 does not appear to continue after 6 months, whereas CMW-1 degrades progressively over 12 months. Moreover, the bending strengths of GBC50 and GBC60 (especially GBC60) were significantly higher than that of CMW-1 throughout. It is believed that GBC60 is strong enough for use under weight-bearing conditions and that its mechanical strength is retained in vivo; however, its dynamic fatigue behavior will need assessment before application in the clinical setting.

Mechanical properties and osteoconductivity of new bioactive composites consisting of partially crystallized glass beads and poly(methyl methacrylate)

New bioactive composites consisting of partially crystallized glass beads as inorganic fillers and poly(methyl methacrylate) (PMMA) as an organic matrix were developed. Two kinds of partially crystallized glass beads, designated Cry820 and Cry850, were newly prepared by the heating of MgO-CaO-SiO(2)-P(2)O(5) glass at 820 and 850 degrees C, respectively. The glass beads were mixed with PMMA to form two new composites designated Cry820C and Cry850C, respectively. The goal of this study was to produce a highly osteoconductive and mechanically strong composite cement with these new fillers. A previously reported composite cement designated AWC, which was composed of apatite- and wollastonite-containing glass ceramic (AW-GC) as a powder filler and the same PMMA polymer used in the new composites, was used as a reference material. The quantity of filler added to each composite was 70 wt %. The bending strength of Cry820C was significantly higher than that of Cry850C. Composites were packed into intramedullary canals of rat tibiae to evaluate their osteoconductivity, as determined by an affinity index. The affinity index, which equaled the length of bone in direct contact with the composite surface expressed as a percentage of the total length of the composite surface, was calculated for each composite. The rats were euthanized at 4, 8, and 25 weeks after implantation. At each time interval studied, Cry820C showed a significantly higher affinity index than AWC up to 25 weeks after implantation. Cry850C showed a significantly higher affinity index than AWC up to 8 weeks and a higher affinity index than AWC at 25 weeks, although the difference was not significant. The values for each composite increased significantly with time up to 25 weeks. Our study revealed that the higher osteoconductivity of the new composites was due to the larger quantity of the glassy phase of the crystallized glass beads at the composite surface and the lower solubility of the PMMA powder to methyl methacrylate monomer. In addition, the spherical shape of the crystallized glass beads gave the new composites strong enough mechanical properties to be useful under weight-bearing conditions. The new composites show promise as alternatives, with improved properties, to conventional PMMA bone cement.

Composites consisting of poly(methyl methacrylate) and alumina powder: an evaluation of their mechanical and biological properties

We developed new composites consisting of comparatively high molecular weight poly(methyl methacrylate) (hPMMA) and delta-alumina powder or alpha-alumina powder (designated delta-APC and alpha-APC, respectively) that allowed direct bone formation on their surfaces in vivo. delta-Alumina powder was manufactured by the fusing and quenching of pulverized alumina powder. It was composed mainly of delta-crystal phases of alumina. The purpose of this study was to evaluate the static mechanical properties and biological properties of these composites. The hPMMA itself was used as a reference material. The bending strength and Young's modulus of both delta-APC and alpha-APC were significantly higher than those of hPMMA, and the alumina composites are believed to be strong enough for use under weight-bearing conditions. The three types of composites were packed into the intramedullary canals of rat tibiae to evaluate osteoconductivity, as determined by an affinity index. Rats were sacrificed 4 and 8 weeks after surgery. The affinity index, equal to the length of bone in direct contact with the composite surface and expressed as a percentage of the total length of the composite surface, was calculated for each composite at each interval. Histologically, new bone had formed along the surfaces of both delta-APC and alpha-APC within 4 weeks. The affinity indices for both delta-APC and alpha-APC increased significantly with time up to 8 weeks. At 8 weeks, the affinity index for delta-APC was significantly higher than the indices for alpha-APC and hPMMA. This study revealed that the excellent osteoconductivity of delta-APC was due to the delta-crystal phases of alumina and the high molecular weight of hPMMA. delta-APC shows promise as a base for developing a highly osteoconductive and mechanically strong biomaterial.

PMMA-based bioactive cement: effect of glass bead filler content and histological change with time

A new bioactive bone cement (designated GBC), which is a polymethyl methacrylate (PMMA)-based composite consisting of bioactive glass beads as an inorganic filler and high molecular-weight PMMA as an organic matrix, has been developed. The purpose of the present study was to evaluate the effect of the filler content on the mechanical properties and osteoconductivity of GBC, to decide the most suitable filler proportion, and to evaluate the degree of cement degradation with time. The bioactive beads, consisting of MgO-CaO-SiO(2)-P(2)O(5)-CaF(2) glass, were added to the cement in various proportions (40-70 wt %). The bending strength of GBC did not differ among the proportions (approximately 136 MPa), but the elastic modulus of bending of GBC increased as the glass bead filler content increased (approximately 4.1-7.2 GPa). The all types of GBC were packed into the intramedullary canals of rat tibiae to evaluate osteoconductivity, as determined by an affinity index calculated as the length of bone in direct contact with the cement surface expressed as a percentage of the total length of the cement surface. Rats were sacrificed at 4, 8, 25, and 39 weeks after implantation, and the affinity index was calculated for each type of GBC at each time point. Histologically, new bone had formed along the surface of all types of GBC within 4 weeks, even in GBC containing only 40 wt % of glass beads. The affinity indices of GBC tended to increase as the proportion of glass bead filler increased and as the implantation period increased. In GBC containing 60 or 70 wt % of glass beads, significant rapid increases in the affinity indices were found from 4 to 8 weeks, and the high values (approximately 70%) were maintained up to 39 weeks. A sign of glass bead degradation was observed at the bone-cement interface in the rat tibiae at 39 weeks. We conclude that, when mechanical properties and osteoconductivity are both taken into consideration, GBC containing 60 or 70 wt % of glass beads is the most suitable formulation, but that further studies are needed to investigate and overcome the degradation.

Whisker-reinforced bioactive composites containing calcium phosphate cement fillers: effects of filler ratio and surface treatments on mechanical properties

Calcium phosphate cement (CPC) sets to form microporous solid hydroxyapatite with excellent osteoconductivity, but its brittleness and low strength prohibit use in stress-bearing locations. The aim of this study was to incorporate prehardened CPC particles and ceramic whiskers in a resin matrix to improve the strength and fracture resistance, and to investigate the effects of key microstructural variables on composite mechanical properties. Two types of whiskers were used: silicon nitride, and silicon carbide. The whiskers were surface-treated by fusing with silica and by silanization. The CPC particle fillers were either silanized or not silanized. Seven mass ratios of whisker-silica/CPC were mixed: 0:1 (no whisker-silica), 1:5, 1:2, 1:1, 2:1, 5:1, and 1:0 (no CPC). Each powder was blended with a bisphenol-a-glycidyl methacrylate-based resin to harden in 2 x 2 x 25 mm molds by two-part chemical curing. The specimens were tested in three-point flexure to measure strength, work-of-fracture (toughness), and elastic modulus. Two-way analysis of variance was used to analyze the data, and scanning electron microscopy was used to examine specimen fracture surfaces. The whisker-silica/CPC ratio had significant effects on composite properties (p < 0.001). When this ratio was increased from 0:1 to 1:0, the strength was increased by about three times, work-of-fracture by five times, and modulus by two times. Whisker surface treatments and CPC filler silanization also had significant effects (p < 0.001) on composite properties. Scanning electron microscopy revealed rough fracture surfaces for the whisker composites with steps and whisker pullout. Resin remnants were observed on the surfaces of the pulled-out whiskers, indicating strong whisker-matrix bonding. In conclusion, incorporating highly osteoconductive CPC fillers and ceramic whiskers yielded composites with substantially improved mechanical properties compared with composites filled with CPC particles without whiskers. The composite properties were determined by whisker-to-CPC ratio and filler surface treatments.

Bioactive bone cement: effects of phosphoric ester monomer on mechanical properties and osteoconductivity

A new bioactive bone cement, designated GBC, has been developed. It consists of polymethyl methacrylate (PMMA) as an organic matrix and bioactive glass beads as an inorganic filler. The bioactive beads, consisting of MgO--CaO--SiO(2)--P(2)O(5)--CaF(2) glass, have been newly designed, and a novel PMMA powder was selected. The purpose of the present study was to evaluate the effects on mechanical properties and osteoconductivity of adding a phosphoric ester (PE) monomer to the cement as an adhesion-promoting agent. Four kinds of cements were prepared: GBC, GBC with PE (designated GBC/PE), a cement consisting of the same PMMA used in GBC with apatite- and wollastonite-containing glass-ceramic (AW-GC) powder (designated AWC), and AWC with PE (designated AWC/PE). Each filler was added to the cement at 70 wt %. Adding PE to either GBC or AWC resulted in increases in the bending strength and decreases in the Young's modulus compared with the unmodified cements. Cements were packed into the intramedullar canals of rat tibiae to evaluate osteoconductivity as determined by an affinity index. Rats were sacrificed at 4 and 8 weeks after operation. The affinity index (length of bone in direct contact with the cement expressed as a percentage of the total length of the cement surface) was calculated for each cement. Adding PE to either GBC or AWC resulted in significant increases in the affinity index compared with the unmodified cements. The affinity index for GBC was significantly higher than that of AWC, and that for GBC/PE was also significantly higher than that of AWC/PE. The affinity indices for each cement increased significantly with time up to 8 weeks. Our study revealed that the higher osteoconductivity of GBC/PE was due to the large alkyl group in the PE monomer, to the hydrophilicity of the phosphoric acid in the PE monomer, and to the higher bioactivity of the bioactive glass beads at the cement surface. GBC/PE shows promise as an alternative bone cement with improved properties compared with conventional PMMA bone cement.

Bioactive bone cement: Effect of silane treatment on mechanical properties and osteoconductivity

A novel bioactive bone cement (GBC) was developed with newly designed bioactive MgO-CaO-SiO(2)-P(2)O(5)-CaF(2) glass beads as the inorganic filler and high molecular weight poly(methyl methacrylate) as the organic matrix. The purpose of this study was to examine the relationship between the amount of the silane coupling agent (gamma-methacryloxy propyl trimethoxy silane) used to treat the glass beads and the mechanical and biological properties of the resultant bone cement. Serial changes in the cement over time were also investigated. Five different kinds of cement, in which the glass beads were treated with different amounts of the coupling agent, were prepared. The quantities of the coupling agent were 0 (control), 0.1, 0.2, 0.5, and 1.0% (w/w) of the glass beads, and the cements were designated GBCs0, GBCs0.1, GBCs0.2, GBCs0.5, and GBCs1.0, respectively. After soaking in water at 75 degrees C for 5 days, GBCs0.1 and GBCs0.2 had significantly higher bending strengths than the other cements. Each GBC was packed into intramedullar canals of rat tibiae to evaluate osteoconductivity, as determined by affinity indices. Rats were killed 4 and 8 weeks after the operation. The affinity index was calculated for each GBC and equaled the length of bone in direct contact with the cement and was expressed as a percentage of the total length of the cement surface. Histologically, new bone had formed along all of the GBC surfaces within 4 weeks. At each time interval, a decreasing trend in the affinity index of GBC was found as the amount of the coupling agent increased. At 8 weeks, no significant change in the affinity index occurred when the amount of the coupling agent increased from 0 to 0.2%, whereas a significant decrease in the affinity index was observed when the amount of the coupling agent increased from 0 to 0.5 or 1.0%. The affinity indices for all the GBCs increased significantly up to 8 weeks. When both the mechanical properties and osteoconductivity were taken into consideration, GBCs0.1 and GBCs0.2 were the best cements, and they showed excellent osteoconductivity and strong enough mechanical properties for clinical use.

A new bioactive bone cement: effect of glass bead filler content on mechanical and biological properties

A new bioactive bone cement (designated GBC), consisting of bioactive glass beads as an inorganic filler and polymethylmethacrylate (PMMA) as an organic matrix, has been developed. The purpose of the present study was to examine the effect of the amount of glass bead filler added to GBC on its mechanical and biological properties, and to decide the most suitable content of filler. Serial changes in GBC with time were also examined. The newly designed bioactive beads, consisting of MgO-CaO-SiO2-P2O5-CaF2 glass, were added to the cement in the proportions 30, 40, 50, 60, and 70 wt %. These cements were designated GBC30, GBC40, GBC50, GBC60, and GBC70, respectively. The compressive strength and the elastic modulus of bending of GBC increased as the glass bead content increased. The various types of GBC were packed into the intramedullar canals of rat tibiae to evaluate osteoconductivity, as determined by an affinity index calculated as the length of bone in direct contact with the cement expressed as a percentage of the total length of the cement surface. Rats were killed at 4 and 8 weeks after the operation and the affinity index was calculated for each type of GBC. Histologically, new bone had formed along the surface of all types of GBC within 4 weeks, even in GBC30 containing only 30 wt % of glass beads. At each time interval studied, there was a trend for the affinity index of GBC to increase as the glass bead filler content increased. There was no significant increase of affinity index between GBC60 and GBC70. The affinity indices for all types of GBC increased significantly with time up to 8 weeks. The handling properties of GBC were comparable to those of conventional PMMA bone cement. We conclude that when mechanical properties and osteoconductivity are both taken into consideration, GBC60 is the most suitable formulation; it shows excellent osteoconductivity and sufficient mechanical strength for clinical use.

Bioactive bone cement: Effect of filler size on mechanical properties and osteoconductivity

A bioactive bone cement (designated GBC), consisting of bioactive glass beads as an inorganic filler and poly(methyl methacrylate) (PMMA) as an organic matrix, has been developed. The purpose of the present study was to examine the effect of the size of the glass beads added as a filler to GBC on its mechanical properties and osteoconductivity. Serial changes in GBC with time were also examined. Four different sizes of beads (mean diameters 4, 5, 9, and 13 microm) consisting of MgO-CaO-SiO(2)-P(2)O(5)-CaF(2) glass were added to four GBC mixes in a proportion of 70 wt %. The bending strength of GBC increased as the mean size of the glass beads decreased. The four GBC mixes were packed into the intramedullary canals of rat tibiae to evaluate osteoconductivity, as determined by an affinity index. Rats were sacrificed at 4 and 8 weeks after surgery. The affinity index, which equaled the length of bone in direct contact with the cement surface expressed as a percentage of the total length of the cement surface, was calculated for each cement at each interval. Histologically, new bone had formed along the surface of all types of GBC within 4 weeks. At each time interval, there was a trend for the affinity index of GBC to increase as the mean glass bead size decreased. The affinity indices for all types of GBC increased significantly with time up to 8 weeks. The handling properties of GBC were comparable to those of conventional PMMA bone cement. We concluded that, considering both mechanical properties and osteoconductivity, GBC made with smaller sized glass beads as filler was the most suitable cement. GBC shows promise as an alternative bone cement with improved properties compared to conventional PMMA bone cement.

Bioactive bone cement: effect of surface curing properties on bone-bonding strength

The fact that bisphenol-a-glycidyl methacrylate (bis-GMA)-based cements contain an uncured surface is believed to play an important role when determining the surface curing properties of the cements. Therefore, in the present study, the bone-bonding strength of cement plates having an uncured surface on one side and a cured surface on the other side has been evaluated. These cement plates were composites of a bis-GMA-based resin with either an apatite- and wollastonite-containing glass-ceramic (AW-GC) powder or a hydroxyapatite (HA) powder, respectively designated AWC and HAC. The amount of each of these powders in a composite cement was 70 wt %. We formulate the hypothesis that the uncured surface of a cement plate is bioactive having bone-bonding properties. The goal of the present study was to indicate the bone-bonding strength of the uncured surfaces of AWC and HAC and compare the strength with the respective cured surfaces by a detaching in vivo test, as well as to histologically examine the bone-cement interface. Each plate has been implanted into the tibiae of male Japanese white rabbits, taking care to retain the surface properties, and the so-called "failure load has been measured using a detaching test followed 8 weeks after implantation. The failure load for AWC-plates at the uncured surface (2.05 +/- 1.11 kgf, n = 8) was significantly higher than AWC at its cured surface side (0.28 +/- 0.64 kgf, n = 8). The failure load for HAC-plates at the uncured surfaces (1.40 +/- 0.68 kgf, n = 8) was significantly higher than HAC at its cured surface (0.00 +/- 0.00 kgf, n = 8). Failure loads for AWC at its uncured and cured surfaces were both higher than for HAC, although not significantly. Direct bone formation has been observed histologically for both AWC and HAC on the uncured surfaces, and a Ca-P-rich layer was observed only at the uncured surface of AWC. These findings strongly suggest that uncured surfaces are useful for exposing a bioactive filler on a surface of composites, being very effective in inducing bone bonding.

Bioactive polymethyl methacrylate-based bone cement: comparison of glass beads, apatite- and wollastonite-containing glass-ceramic, and hydroxyapatite fillers on mechanical and biological properties

A new bioactive bone cement (designated GBC) consisting of polymethyl methacrylate (PMMA) as an organic matrix and bioactive glass beads as an inorganic filler has been developed. The bioactive beads, consisting of MgO-CaO-SiO(2)-P(2)O(5)-CaF(2) glass, have been newly designed, and a novel PMMA powder was selected. The purpose of the present study was to compare this new bone cement GBC's mechanical properties in vitro and its osteoconductivity in vivo with cements consisting of the same matrix as GBC and either apatite- and wollastonite-containing glass-ceramic (AW-GC) powder (designated AWC) or sintered hydroxyapatite (HA) powder (HAC). Each filler added to the cements amounted to 70 wt %. The bending strength of GBC was significantly higher than that of AWC and HAC (p < 0.0001). Cements were packed into intramedullar canals of rat tibiae in order to evaluate osteoconductivity as determined by an affinity index. Rats were sacrificed at 2, 4, and 8 weeks after operation. An affinity index, which equaled the length of bone in direct contact with the cement expressed as a percentage of the total length of the cement surface, was calculated for each cement. At each time interval studied, GBC showed a significantly higher affinity index than AWC or HAC up to 8 weeks after implantation (p < 0.03). The value for GBC increased significantly with time up to 8 weeks (p < 0.006). The handling property of GBC was comparable with that of PMMA bone cement. Our study revealed that the higher osteoconductivity of GBC was due to the higher bioactivity of the bioactive glass beads at the cement surface and the lower solubility of the new PMMA powder to MMA monomer. In addition, it was found that the smaller spherical shape and glassy phase of the glass beads gave GBC strong enough mechanical properties to be useful under weight-bearing conditions. GBC shows promise as an alternative with improved properties to the conventionally used PMMA bone cement.

Bioactive polymethyl methacrylate-based bone cement: comparison of glass beads, apatite- and wollastonite-containing glass-ceramic, and hydroxyapatite fillers on mechanical and biological properties

A new bioactive bone cement (designated GBC) consisting of polymethyl methacrylate (PMMA) as an organic matrix and bioactive glass beads as an inorganic filler has been developed. The bioactive beads, consisting of MgO-CaO-SiO(2)-P(2)O(5)-CaF(2) glass, have been newly designed, and a novel PMMA powder was selected. The purpose of the present study was to compare this new bone cement GBC's mechanical properties in vitro and its osteoconductivity in vivo with cements consisting of the same matrix as GBC and either apatite- and wollastonite-containing glass-ceramic (AW-GC) powder (designated AWC) or sintered hydroxyapatite (HA) powder (HAC). Each filler added to the cements amounted to 70 wt %. The bending strength of GBC was significantly higher than that of AWC and HAC (p < 0.0001). Cements were packed into intramedullar canals of rat tibiae in order to evaluate osteoconductivity as determined by an affinity index. Rats were sacrificed at 2, 4, and 8 weeks after operation. An affinity index, which equaled the length of bone in direct contact with the cement expressed as a percentage of the total length of the cement surface, was calculated for each cement. At each time interval studied, GBC showed a significantly higher affinity index than AWC or HAC up to 8 weeks after implantation (p < 0.03). The value for GBC increased significantly with time up to 8 weeks (p < 0.006). The handling property of GBC was comparable with that of PMMA bone cement. Our study revealed that the higher osteoconductivity of GBC was due to the higher bioactivity of the bioactive glass beads at the cement surface and the lower solubility of the new PMMA powder to MMA monomer. In addition, it was found that the smaller spherical shape and glassy phase of the glass beads gave GBC strong enough mechanical properties to be useful under weight-bearing conditions. GBC shows promise as an alternative with improved properties to the conventionally used PMMA bone cement.

Alumina powder/Bis-GMA composite: effect of filler content on mechanical properties and osteoconductivity

Three composites consisting of alumina powder dispersed in a bisphenol-a-glycidyl methacrylate (Bis-GMA) matrix were prepared and evaluated to assess the effect of alumina powder content on the mechanical properties and osteoconductivity of the composite. The alumina powder composites (APC) consisted of alumina powder (AL-P) as the inorganic filler dispersed in a Bis-GMA matrix that was solidified by a radical polymerization process. Prior to polymerization the AL-P was mixed with the monomers in proportions of 50%, 70%, and 80% by weight (APC50, APC70, and APC80). A fused silica-glass-filled composite containing 70% glass by weight (SGC70) was used as a control. The compressive and bending strengths, the elastic modulus in bending, and the bending strain of the composites increased as the AL-P content increased. We also evaluated the composites in vivo by implanting them into the medullary canals of rat tibiae. To compare the osteoconductivity of the composites, an affinity index was calculated for each composite; the affinity index equals the length of a bone in direct apposition to the composite and is expressed as a percentage of the total length of the composite surface. Microradiographic examination for periods of up to 26 weeks after implantation revealed that APC50, APC70, and APC80 all exhibited excellent osteoconductivity and made direct contact with the bone with no interposed soft tissues. However, the higher the AL-P content of the composite, the higher the osteoconductivity, especially at 4 weeks after the operation. Moreover, the amount of bone directly apposed to the composite surface increased with time. In contrast, little bone formation was seen on the surface of SGC70, even after 26 weeks. Observation by scanning electron microscope-energy dispersive X-ray microanalysis demonstrated that bone made direct contact with the APC surface through a layer containing calcium, phosphorus, and alumina powder. These results suggest that APC shows promise as a basis for developing mechanically strong and highly osteoconductive composites.