Structural and morphological study of pulsed laser deposited calcium phosphate bioceramic coatings: influence of deposition conditions, laser parameters, and target properties

Substituted Hydroxyapatite, Glass, and Glass-Ceramic Thin Films Deposited by Nanosecond Pulsed Laser Deposition (PLD) for Biomedical Applications: A Systematic Review

The deposition of thin films of bioactive materials is the most common approach to improve the bone bonding ability of an implant surface. With this purpose, several wet and plasma assisted deposition methods were proposed in the scientific literature. In this review, we considered films obtained by nanosecond Pulsed Laser Deposition (PLD). Since hydroxyapatite (HA) has composition and structure similar to that of the mineral component of the bone, the initial studies focused on the selection of experimental conditions that would allow the deposition of films that retain HA stoichiometry and crystallinity. However, biological apatite was found to be a poorly crystalline and multi-substituted mineral; consequently, the attention of researchers was oriented towards the deposition of substituted HA, glass (BG), and glass-ceramic (BGC) bioactive materials to exploit the biological relevance of foreign ions and crystallinity. In this work, after a description of the nanosecond ablation and film growth of ceramic materials, we reported studies on the mechanism of HA ablation and deposition, evidencing the peculiarities of PLD. The literature concerning the PLD of ion substituted HA, BG, and BGC was then reviewed and the performances of the coatings were discussed. We concluded by describing the advantages, limitations, and perspectives of PLD for biomedical applications.

Significance of calcium phosphate coatings for the enhancement of new bone osteogenesis--a review

A systematic analysis of results available from in vitro, in vivo and clinical trials on the effects of biocompatible calcium phosphate (CaP) coatings is presented. An overview of the most frequently used methods to prepare CaP-based coatings was conducted. Dense, homogeneous, highly adherent and biocompatible CaP or hybrid organic/inorganic CaP coatings with tailored properties can be deposited. It has been demonstrated that CaP coatings have a significant effect on the bone regeneration process. In vitro experiments using different cells (e.g. SaOS-2, human mesenchymal stem cells and osteoblast-like cells) have revealed that CaP coatings enhance cellular adhesion, proliferation and differentiation to promote bone regeneration. However, in vivo, the exact mechanism of osteogenesis in response to CaP coatings is unclear; indeed, there are conflicting reports of the effectiveness of CaP coatings, with results ranging from highly effective to no significant or even negative effects. This review therefore highlights progress in CaP coatings for orthopaedic implants and discusses the future research and use of these devices. Currently, an exciting area of research is in bioactive hybrid composite CaP-based coatings containing both inorganic (CaP coating) and organic (collagen, bone morphogenetic proteins, arginylglycylaspartic acid etc.) components with the aim of promoting tissue ingrowth and vascularization. Further investigations are necessary to reveal the relative influences of implant design, surgical procedure, and coating characteristics (thickness, structure, topography, porosity, wettability etc.) on the long-term clinical effects of hybrid CaP coatings. In addition to commercially available plasma spraying, other effective routes for the fabrication of hybrid CaP coatings for clinical use still need to be determined and current progress is discussed.

Calcium orthophosphate coatings, films and layers

In surgical disciplines, where bones have to be repaired, augmented or improved, bone substitutes are essential. Therefore, an interest has dramatically increased in application of synthetic bone grafts. As various interactions among cells, surrounding tissues and implanted biomaterials always occur at the interfaces, the surface properties of the implants are of the paramount importance in determining both the biological response to implants and the material response to the physiological conditions. Hence, a surface engineering is aimed to modify both the biomaterials, themselves, and biological responses through introducing desirable changes to the surface properties of the implants but still maintaining their bulk mechanical properties. To fulfill these requirements, a special class of artificial bone grafts has been introduced in 1976. It is composed of various mechanically stable (therefore, suitable for load bearing applications) biomaterials and/or bio-devices with calcium orthophosphate coatings, films and layers on their surfaces to both improve interactions with the surrounding tissues and provide an adequate bonding to bones. Many production techniques of calcium orthophosphate coatings, films and layers have been already invented and new promising techniques are continuously investigated. These specialized coatings, films and layers used to improve the surface properties of various types of artificial implants are the topic of this review.

Laser surface modification of titanium substrate for pulsed laser deposition of highly adherent hydroxyapatite

Biomedical implant devices made out of titanium and its alloys are benefited by a modified surface or a bioactive coating to enhance bone bonding ability and to function effectively in vivo for the intended period of time. In this respect hydroxyapatite coating developed through pulsed laser deposition is a promising approach. Since the success of the bioactive ceramic coated implant depends mainly on the substrate-coating strength; an attempt has been made to produce micro patterned surface structure on titanium substrate for adherent hydroxyapatite coating. A pulsed Nd-YAG laser beam (355 nm) with 10 Hz repetition rate was used for surface treatment of titanium as well as hydroxyapatite deposition. The unfocussed laser beam was used to modify the substrate surface with 500-18,000 laser pulses while keeping the polished substrate in water. Hydroxyapatite deposition was done in a vacuum deposition chamber at 400 °C with the focused laser beam under 1 × 10⁻³ mbar oxygen pressure. Deposits were analyzed to understand the physico-chemical, morphological and mechanical characteristics. The obtained substrate and coating surface morphology indicates that laser treatment method can provide controlled micro-topography. Scratch test analysis and microindentation hardness values of coating on laser treated substrate indicate higher mechanical adhesion with respect to coatings on untreated substrates.

Biocompatibility and bioactivity enhancement of Ce stabilized ZrO(2) doped HA coatings by controlled porosity change of Al(2) O(3) substrates

Al(2) O(3) substrates with controlled porosity were manufactured from nanosized powders obtained by plasma processing. It was observed that when increasing the sintering temperature the overall porosity was decreasing, but the pores got larger. In a second step, Ce stabilized ZrO(2) doped hydroxyapatite coatings were pulsed laser deposited onto the Al(2) O(3) substrates. It was shown that the surface morphology, consisting of aggregates and particulates in micrometric range, was altered by the substrate porosity and interface properties, respectively. TEM studies evidenced that Ce stabilized ZrO(2) doped HA particulates ranged from 10 to 50 nm, strongly depending on the Al(2) O(3) porosity. The coatings consisted of HA nanocrystals embedded in an amorphous matrix quite similar to the bone structure. These findings were congruent with the increased biocompatibility and bioactivity of these layers confirmed by enhanced growing and proliferation of human mesenchymal stem cells.

Behaviour of MG-63 osteoblast-like cells on wood-based biomorphic SiC ceramics coated with bioactive glass

The aim of this study was to test the in vitro cytotoxicity of wood-based biomorphic Silicon Carbide (SiC) ceramics coated with bioactive glass, using MG-63 human osteoblast-like cells, with a view to their application in bone implantology. To better understand the scope of this study, it should be taken into account that biomorphic SiC ceramics have only recently been developed and this innovative product has important properties such as interconnected porosity, high strength and toughness, and easy shaping. In the solvent extraction test, all the extracts had almost no effect on cellular activity even at 100% concentration, and cells incubated in the bioactive glass-coated SiC ceramics extracts showed a proliferation rate similar to that of the Thermanox control. There were no significant differences when the cellular attachment response of the cells on the wood-based biomorphic SiC ceramics, uncoated or coated with bioactive glass, was compared to the one exhibited by reference materials like Ti6Al4V and bulk bioactive glass. This fact looks very promising for biomedical applications.

Control of phase composition in hydroxyapatite/tetracalcium phosphate biphasic thin coatings for biomedical applications

Biphasic calcium phosphates comprising well-controlled mixtures of nonresorbable hydroxyapatite and other resorbable calcium phosphate phases often exhibit a combination of enhanced bioactivity and mechanical stability that is difficult to achieve in single-phase materials. This makes these biphasic bioceramics promising substrate materials for applications in bone tissue regeneration and repair. In this paper we report the synthesis of highly crystalline, biphasic coatings of hydroxyapatite/tetracalcium phosphate with control over the weight fraction of the constituent phases. The coatings were produced by pulsed laser deposition using ablation targets of pure crystalline hydroxyapatite. The fraction of tetracalcium phosphate phase in the coatings was controlled by varying the substrate temperature and the partial pressure of water vapor in the deposition chamber. A systematic study of phase composition in the hydroxyapatite/tetracalcium phosphate biphasic coatings was performed with X-ray diffraction. Tetracalcium phosphate in the coatings obtained at high substrate temperature is not formed by partial conversion of previously deposited hydroxyapatite. Instead, it is produced by nucleation and growth of tetracalcium phosphate itself from the ablation products of the hydroxyapatite target or by accretion of tetracalcium phosphate grains formed during ablation. This finding was confirmed by formation of calcium oxide, not tetracalcium phosphate, after annealing of pure hydroxyapatite coatings at high temperatures of 700-850 degrees C.

Osseointegration of a hydroxyapatite-coated multilayered mesh stem

A new type of porous coating for hip prostheses called "multilayered mesh" was tested under weight-bearing conditions. The surface of the stem is constructed of titanium mesh produced by etching. The hip stems of hydroxyapatite (HA)-coated multilayered mesh and conventional beads were implanted into canine right hips, and animals were killed 3, 6 and 10 weeks and 6 and 12 months after implantation. Shear strength between the implant and the bone was evaluated by the push-out test. Bone ingrowth was calculated from backscattered electron imaging-scanning electron microscopy (BEI-SEM) images of transverse sections. Toluidine blue stained sections and the BEI-SEM images were evaluated histologically. The break sites of the specimens after the push-out test were evaluated on BEI-SEM images of longitudinal sections. The mean push-out strength of the HA-coated multilayered mesh samples was greater than that of the beads-coated samples every time tested, and the HA-coated multilayered mesh implants had significantly stronger push-out strength at 3 and 6 weeks (p<0.05). The strength of the HA-coated multilayered mesh implants was even greater at 6 and 12 months, whereas the strength of the beads-coated samples decreased. The HA-coated multilayered mesh implants showed significantly higher percentages of bone ingrowth than the beads-coated implants every time tested, except at 6 months (p<0.05). At 6 and 12 months, the bone ingrowth data for the HA-coated multilayered mesh implants increased, whereas it decreased for the beads-coated implants. The new bone formation had reached the bottom of the porous area of the HA-coated multilayered mesh surface by 3 weeks, but not had reached the bottom of the conventional beads surface. At 6 and 12 months, the smaller pores of the bead surface stopped the thickening of trabecular bone, and at 12 months, the break sites were at the bone-implant interface of the bead surface, whereas they were on the bone side of the HA-coated multilayered mesh surface. The difference between the break sites was significant at 12 months (p<0.05). The HA-coated multilayered mesh stem provided faster, stronger, and more durable osseointegration than the conventional bead stem.

A low-temperature biomimetic calcium phosphate surface enhances early implant fixation in a rat model

The present study demonstrates increased early mechanical fixation of titanium implants coated with a new biomimetic apatite surface in a rat model. Male Sprague-Dawley rats received unilateral femoral medullary implants for periods of 1-4 weeks. The strength of fixation of the implant to the host bone increased more rapidly in the group receiving apatite-treated implants compared with the control group as evidenced by the apatite group's 21-fold greater fixation strength at 1 week (p = 0.009), 4-fold greater fixation strength at 2 weeks (p = 0.041), and 2-fold greater fixation strength at 4 weeks (p = 0.093) compared with the control. Fixation strength was correlated with bone-implant contact as determined from micro computed tomography assessment of the specimens (r2 = 0.338, p = 0.011 in the control group and r2 = 0.543, p < 0.001 in the apatite group). Furthermore, for a given amount of bone-implant contact, the fixation strength was higher in the apatite group than in the control group (p = 0.011), suggesting that the bone formed a stronger bond to the apatite coating than to the titanium. This difference in bonding strength accounted for the difference in mechanical behavior.

Characterization of calcium phosphate coatings deposited by Nd:YAG laser ablation at 355 nm: influence of thickness

Calcium phosphate coatings were deposited by pulsed laser ablation with a radiation of 355 nm from a Nd:YAG laser. All the coatings were obtained at the same conditions, but deposition was stopped after different number of pulses to get coatings with different thickness. The influence of thickness in the structural and mechanical properties of the coatings was investigated. Coatings structure was characterised by scanning electron microscopy, grazing incidence X-ray diffractometry and Raman spectroscopy. The mechanical properties were evaluated by scratch test. The morphology of the coatings is dominated by the presence of droplets. The coatings are composed mainly of hydroxyapatite, alpha tricalcium phosphate and amorphous calcium phosphate. Thinner coatings withstand higher loads of failure in the scratch test.