On the mechanism of background silver staining during sodium dodecyl sulphate-polyacrylamide gel electrophoresis

Development of 3D Printed pNIPAM-Chitosan Scaffolds for Dentoalveolar Tissue Engineering

While available treatments have addressed a variety of complications in the dentoalveolar region, associated challenges have resulted in exploration of tissue engineering techniques. Often, scaffold biomaterials with specific properties are required for such strategies to be successful, development of which is an active area of research. This study focuses on the development of a copolymer of poly (N-isopropylacrylamide) (pNIPAM) and chitosan, used for 3D printing of scaffolds for dentoalveolar regeneration. The synthesized material was characterized by Fourier transform infrared spectroscopy, and the possibility of printing was evaluated through various printability tests. The rate of degradation and swelling was analyzed through gravimetry, and surface morphology was characterized by scanning electron microscopy. Viability of dental pulp stem cells seeded on the scaffolds was evaluated by live/dead analysis and DNA quantification. The results demonstrated successful copolymerization, and three formulations among various synthesized formulations were successfully 3D printed. Up to 35% degradability was confirmed within 7 days, and a maximum swelling of approximately 1200% was achieved. Furthermore, initial assessment of cell viability demonstrated biocompatibility of the developed scaffolds. While further studies are required to achieve the tissue engineering goals, the present results tend to indicate that the proposed hydrogel might be a valid candidate for scaffold fabrication serving dentoalveolar tissue engineering through 3D printing.

Cluster-Dominated Electrochemiluminescence of Tertiary Amines in Polyethyleneimine Nanoparticles: Mechanism Insights and Sensing Application

Designing and screening highly efficient and cost-effective luminophores have always been a challenge to develop sensitive electrochemiluminescence (ECL) biosensors. Herein, polyethyleneimine nanoparticles (PEI NPs), a kind of nonconjugated polymer (NCP) NPs with tertiary amine clusters, were developed as an ECL luminophore. Specifically, PEI NPs were synthesized by a one-step hydrothermal method using PEI and formaldehyde. The properties of PEI NPs were investigated in detail using photochemical and electrochemical techniques. The results showed cluster-dominated luminescence of tertiary amines in PEI NPs via "through-space conjugation". This non-negligible ECL performance (at 631 nm) was also verified by the initiated reduction-oxidation process. With persulfate as a coreactant, PEI NPs acted as both the luminophore and coreaction accelerator to enhance the ECL intensity remarkably, which was eightfold higher than that of isolated PEI. Moreover, choosing dopamine as the model target, a highly sensitive "signal off" ternary ECL sensor was constructed utilizing PEI NPs as the luminophore. Dopamine could be oxidized to benzoquinone at the sensing interface, quenching the signal via ECL energy transfer. Free from any signal amplification, the proposed sensor achieved a low detection limit (4.3 nM) for target monitoring with good selectivity and stability. This strategy not only provides a unique perspective for designing novel efficient and facile ECL luminophores of tertiary amines but also broadens the biological application of NCP NPs.

Artifactual sulfation of silver-stained proteins: implications for the assignment of phosphorylation and sulfation sites

Sulfation and phosphorylation are post-translational modifications imparting an isobaric 80-Da addition on the side chain of serine, threonine, or tyrosine residues. These two post-translational modifications are often difficult to distinguish because of their similar MS fragmentation patterns. Targeted MS identification of these modifications in specific proteins commonly relies on their prior separation using gel electrophoresis and silver staining. In the present investigation, we report a potential pitfall in the interpretation of these modifications from silver-stained gels due to artifactual sulfation of serine, threonine, and tyrosine residues by sodium thiosulfate, a commonly used reagent that catalyzes the formation of metallic silver deposits onto proteins. Detailed MS analyses of gel-separated protein standards and Escherichia coli cell extracts indicated that several serine, threonine, and tyrosine residues were sulfated using silver staining protocols but not following Coomassie Blue staining. Sodium thiosulfate was identified as the reagent leading to this unexpected side reaction, and the degree of sulfation was correlated with increasing concentrations of thiosulfate up to 0.02%, which is typically used for silver staining. The significance of this artifact is discussed in the broader context of sulfation and phosphorylation site identification from in vivo and in vitro experiments.