Valproate-Selective Membrane Electrode Based on Gallium(III) Tetraphenylporphyrin

Quantitation of valproic acid in pharmaceutical preparations using dispersive liquid-liquid microextraction followed by gas chromatography-flame ionization detection without prior derivatization

Dispersive liquid-liquid microextraction (DLLME), coupled with gas chromatography-flame ionization detection (GC-FID), has been successfully used for the extraction and determination of valproic acid (VPA) in pharmaceutical preparations. In the developed method, an appropriate mixture of extracting and disperser solvents was rapidly injected into an aqueous sample. Having formed a cloudy solution, the mixture was centrifuged and then the extracting solvent was sedimented at the bottom of a conical test tube. The extract was then injected into a GC system directly, without any further pretreatment. Initially, microextraction efficiency factors were optimized and the optimum experimental conditions found were as follows: tetrachloroethylene (9.0 µL) as extracting solvent; acetone (1.0 mL) as disperser solvent; 5 mL acidic aqueous sample (pH 1) without salt addition. Under the selected conditions, the calibration curve showed linearity in the range of 0.1-5.0 mg/L with regression coefficient corresponding to 0.9998. The limit of detection was found to be 0.05 mg/L. Finally, the method was applied for the determination of VPA in two different pharmaceutical preparations. A reasonable intra-assay (3.9-10.8%, n = 3) and inter-assay (5.6-11.4%, n = 3) precision illustrated the good performance of the analytical procedure. The protocol proved to be rapid and cost-effective for screening purposes.

Determination of valproic acid in human serum and pharmaceutical preparations by headspace liquid-phase microextraction gas chromatography-flame ionization detection without prior derivatization

An efficient and fast extraction technique for the enrichment of valproic acid from human blood serum samples using the headspace liquid phase microextraction (HS-LPME) combined with gas chromatography (GC) analysis has been developed. The extraction was conducted by suspending a 2 microL drop of organic solvent in a 1 mL serum sample; following 20 min of extraction, withdrawing organic solvent into a syringe and injection into a GC with a flame ionization detector (FID), without any further pre-treatment. Four organic solvents, 1-decanole, benzyl alcohol, 1-octanol and n-dodecane, were studied as extractants, and n-dodecane was found to be the most sensitive solvent for valproic acid. The results revealed that HS-LPME is suitable for the successful extraction of valproic acid from human blood serum samples. Parameters like extraction time, ionic strength, pH, organic solvent volume, and temperature of the sample were studied and optimized to obtain the best extraction results. An enrichment factor of 27-fold was achieved in 20 min. The procedure resulted in a relative standard deviation of <13.2% (n=7) and a linear calibration range from 2 to 20 microg mL(-1) (r>0.98), and the limit of detection was 0.8 microg mL(-1) in serum blank samples. Overall, LPME proved to be a fast, sensitive and simple tool for the preconcentration of valproic acid from real samples. The proposed method was also applied to the analysis of valproate in pharmaceutical preparations.

Potentiometric behaviour of ion selective electrodes based on iron porphyrins: the influence of porphyrin substituents on the response properties and analytical determination of diclofenac in pharmaceutical formulations

The potentiometric response characteristics of diclofenac selective electrodes based on Fe(III) tetraphenylporphyrin-chloride (Fe(III)TPP-Cl) and Fe(III) tetrakis(pentafluorophenyl)porphyrin-chloride (Fe(III)TPFPP-Cl) in different mediator solvents and ionic additives are compared. The sensitivity, working range, detection limit, response mechanism, and selectivity of the membrane sensor show a significant dependence on the type of carrier substituent and on the pH value of the sample solution. Studies performed with different amounts of cationic additive (tetra-n-octylammoniumbromide (TOABr)) and anionic additive (sodium tetraphenylborate (NaTPB)) in the membranes allowed the determination of the potentiometric mechanism of action of the used metalloporphyrins. For the analysis of real samples, Fe(III)TPFPP-Cl (type G), prepared in o-NPOE, incorporating 10 mol% of TOABr, was used. This potentiometric unit presented a linear response towards diclofenac concentrations between 10(-5) and 10(-2)mol l(-1) ( I=0.1 mol l(-1)) and slopes of about -59 mV dec(-1), exhibiting a response time of 10s in a buffered solution of ammonia-ammonium sulphate with pH 9.9. The potentiometric analysis of sodium diclofenac in pharmaceutical formulations was carried out by direct potentiometry and the obtained results were compared to those provided by HPLC, presenting relative errors inferior to 1.0%.

Construction and evaluation of PVC and sol-gel sensor membranes based on Mn(III)TPP-Cl. Application to valproate determination in pharmaceutical preparations

The construction and general performance of new valproate-selective electrodes based on manganese(III) tetraphenylporphyrin [Mn(III)TPP-Cl], as an ionophore, are presented. The ionophore was incorporated into PVC and ceramic membranes (sol-gel) based on methyltriethoxysilane. The influence of membrane composition and pH and the effect of lipophilic cationic and anionic additives in PVC membranes were investigated concerning their influence on the slope, response time, selectivity and lifetime of the electrodes. The PVC membrane without additive and the sol-gel membrane presented slopes and practical limits of detection of -60.8 mV dec(-1) and 5x10(-6) mol l(-1) and -60.3 mV dec(-1) and 1x10(-4) mol l(-1), respectively. The sol-gel membranes displayed higher selectivity for valproate when compared with PVC membranes. These two types of electrodes were coupled to a sequential-injection analysis (SIA) system for the direct determination of valproate in pharmaceutical formulations. The association of Mn(III)TPP-Cl with the sol-gel support inserted in a SIA system provided potentiometric sensors with an analytical range of 1x10(-3)-5x10(-2) mol l(-1), with a sample rate of 55 samples per hour and a sample and carrier consumption of 140 and 2,500 microl per determination, respectively.