Strategic Shuffling of Clay Layers to Imbue Them with Responsiveness

Superhigh and Robust Ion Selectivity in Membranes Assembled with Monolayer Clay Nanosheets

It is crucial to control the ion transport in membranes for various technological applications such as energy storage and conversion. The emerging functional two-dimensional (2D) nanosheets such as graphene oxide and MXenes show great potential for constructing ordered nanochannels, but the assembled membranes suffer from low ion selectivity and stability. Here a class of robust charge-selective membranes with superhigh cation/anion selectivity, which are assembled with monolayer nanosheets of cationic/anionic clays that inherently have permanent and uniform charges on each layer is reported. The transport number of cations/anions of cationic vermiculite nanosheet membranes (VNMs)/anionic Co-Al layered double hydroxide (CoAl-LDH) nanosheet membranes is over 0.90 in different NaCl concentration gradients, outperforming all the reported ion-selective membranes. Importantly, this excellent ion selectivity can persist at high-concentration salt solutions, under acidic and alkaline conditions, and for a wide range of ions of different sizes and charges. By coupling a pair of cation-selective vermiculite membrane and anion-selective CoAl-LDH membrane, a reverse electrodialysis device which shows an output power density of 0.7 W m-2 and energy conversion efficiency of 45.5% is constructed. This work provides a new strategy to rationally design high-performance ion-selective membranes by using 2D nanosheets with inherent surface charges for controllable ion-transport applications.

Synthesis and characterization of a phosphotungstic acid composite carrier and its application in solid chlorine dioxide disinfectant

The attapulgite was introduced into phosphotungstic acid and SBA-15 to achieve the slow release of chlorine dioxide and reducing the escape of chlorine dioxide gas to increase the reacting time and improve disinfection efficiency.

Robust Jumping Actuator with a Shrimp-Shell Architecture

It is highly desirable to develop compact- and robust-film jumping robots that can withstand severe conditions. Besides, the demands for strong actuation force, large bending curvature in a short response time, and good environmental tolerance are significant challenges to the material design. To address these challenges, this paper reports the fabrication of a thin-film jumping actuator, which exhibits a shrimp-shell architecture, from a conjugated ladder polymer (cLP) that is connected by carbon nanotube (CNT) sheets. The hierarchical porous structure ensures the fast absorption and desorption of organic vapor, thereby achieving a high response rate. The actuator does not exhibit shape distortion at temperatures of up to 225 °C and in concentrated sulfuric acid, as well as when immersed in many organic solvents. This work avails a new design strategy for high-performance actuators that function under harsh and complicated conditions.

Robust hemostatic bandages based on nanoclay electrospun membranes

Death from acute hemorrhage is a major problem in military conflicts, traffic accidents, and surgical procedures, et al. Achieving rapid effective hemostasis for pre-hospital care is essential to save lives in massive bleeding. An ideal hemostasis material should have those features such as safe, efficient, convenient, economical, which remains challenging and most of them cannot be achieved at the same time. In this work, we report a rapid effective nanoclay-based hemostatic membranes with nanoclay particles incorporate into polyvinylpyrrolidone (PVP) electrospun fibers. The nanoclay electrospun membrane (NEM) with 60 wt% kaolinite (KEM1.5) shows better and faster hemostatic performance in vitro and in vivo with good biocompatibility compared with most other NEMs and clay-based hemostats, benefiting from its enriched hemostatic functional sites, robust fluffy framework, and hydrophilic surface. The robust hemostatic bandages based on nanoclay electrospun membrane is an effective candidate hemostat in practical application.

Rapid, easy and effective haemostasis is needed to reduce the loss of life from traumatic haemorrhage. Here, the authors report on the creation of polymer-nanoclay electrospun membranes and demonstrate haemostatic effects showing superior effects to other clay based haemostats.

Application of reduced graphene oxide-based actuators for real-time chemical sensing of liquid and vapour phase contaminants

The possibility of employing responsive materials for the in situ detection of chemical contaminants in the liquid phase is demonstrated here.

Controllable, Bidirectional Water/Organic Vapors Responsive Actuators Fabricated by One-Step Thiol-Ene Click Polymerization

It is challenging to synthesize stimuli-responsive materials with the well-balanced performance of fast stimulus-response speed, good mechanical strength, multi-functionality, and deformation diversity as well. This work reports a facile, one-step thiol-ene click polymerization strategy for preparation of water/acetone vapor-responsive hierarchical films, by using diallyl terephthalate (P) as hydrophobic ene-monomer, 1,4-diallyl-1,4-diazabicyclo [2.2.2]octane-1,4-diium bromide (B) as hydrophilic ene-monomer, and pentaerythritol tetra(3-mercaptopropionate) (PETMP) as thiol monomer. Besides, by taking advantage of the specific hydrophilic/hydrophobic induction effect of substrate and adjusting the molar ratio of P to B, P₆₀ B₄₀ -HPI film is fabricated on hydrophilic substrate "with plasma treatment" whereas P₈₀ B₂₀ -HPO film is obtained on hydrophobic substrate "without plasma treatment". Their "upper-dense and lower-porous" structural feature ensured the excellent combination of fast stimuli-response speed endowed by the porous structure and good mechanical strength enhanced by the upper dense surface. Both films are bidirectional water/acetone vapor-responsive materials, but their bending directions responding to the stimuli factors are completely opposite. This strategy showed great potential in the development of smart stimuli-responsive materials.

Unusually fast and large actuation from multilayer polyelectrolyte thin films

Polymers responsive to external stimuli (e.g., electric field, chemical vapor, light) are of great interest for smart materials such as sensors and soft robotics. A vapor-driven multilayer polymer actuator, capable of fast and large-scale actuation, is described here. This Janus-like actuator is prepared with two polyelectrolyte multilayer systems (polyethylenimine (PEI)/poly(acrylic acid) (PAA) and polyurethane (PU)/poly(acrylic acid) (PAA)) using layer-by-layer assembly (LbL). The differing hydrophilicity of these two nanocoatings results in different swelling behavior in water and organic solvents, which leads to vapor-responsive mechanical motion. The bending/curling degree of this polymeric actuator can be precisely controlled by changing the thickness ratio of the two layers. A vapor sensor was constructed to demonstrate the environmental detection ability of this unique actuator.

Reconstruction of Soil Components into Multifunctional Freestanding Membranes

Multifunctional freestanding membranes are prepared by tuning the structure of ubiquitous soil components, viz. clay and humic acids. Cross-linking of exfoliated clay layers with purified humic acids not only conferred mechanical strength but also enhanced chemical robustness of the membranes. The percolated network of molecularly sized channels of the soil membranes exhibits characteristic nanofluidic phenomena. Electrical conductivity is induced to otherwise insulating soil membranes by heating in an inert atmosphere, without affecting their nanofluidic ionic conductivity. The soil membranes also provided a new platform to prepare and study mixed conducting materials. Strips of heated membranes are shown to exhibit excellent sensitivity toward NH₃ gas under atmospheric conditions.

Molecular Structure and Decomposition Kinetics of Kaolinite/Alkylamine Intercalation Compounds

Although the development of clay/polymer nanocomposites and their applications have attracted much attention in recent years, a thorough understanding of the structure and the decomposition mechanism of clay/polymer nanocomposites is still lacking. In this research, the intercalation of kaolinite (Kaol) with different alkylamines were investigated by X-ray diffracion (XRD), Fourier-transform infrared spectroscopy (FTIR), and thermogravimetry and differential scanning calorimetry (TG-DSC). The results showed that the intercalation of Kaol/methanol compound with hexylamine (HA), dodecylamine (DA), and octadecylamine (OA) led to the expansion of the interlayer distance and resulted in the dominant basal diffraction at 2.86, 4.08, and 5.66 nm. The alky chains of HA, DA, and OA are tilted toward the Kaol surface in bilayer with an inclination angle of ~40°. The most probable mechanism function, activation energy E, and pre-exponential factor A were obtained by mutual authentication using KAS and Ozawa methods, itrative and Satava integral method. The average activation energy E of the three intercalation compounds are 104.44, 130.80, and 154.59 kJ mol-1, respectively. It shows a positive correlation with the alkyl chain length. The pre-exponential factor A was estimated to be 1.09 × 1015, 1.15 × 108, and 4.17 × 1021 s-1, respectively. The optimized mechanism function for the decomposition of alkylamine is G(α) = [(1-α) -1/3-1]2.

An asymmetric graphene oxide film for developing moisture actuators

Although Janus films of different compositions have been commonly utilized to develop moisture actuators due to the different capabilities of swelling in materials, a sole material with a distinct structural design is also able to provide moisture-actuation. In this study, we simply used graphene oxide (GO) to fabricate a sole GO film with an asymmetric structure which consisted of a wavy layer and a smooth layer. Due to the asymmetric structure and excellent hygroscopicity of the GO material, the asymmetric graphene oxide (AGO) film (2.5 × 0.5 cm2) was responsive to moisture and showed a maximum bending angle change of ≈1800° as the relative humidity (RH) changed. Compared with other reports about moisture actuators, the AGO film exhibited a superior bending capability. Furthermore, we propose a novel mechanism for moisture actuation of the AGO film based on our detailed observations, and a wavy structure has been introduced for showing great potential in bending deformation. Finally, the AGO film was used as a grabber to grab a leaf and it exhibited good capability to twine around a plastic rod. This work provides a novel pathway for the development of moisture-responsive materials for potential applications in robotics, artificial muscles and switches.