Stabilization of Sn Anode through Structural Reconstruction of a Cu-Sn Intermetallic Coating Layer

Rich-Carbonyl Carbon Catalysis Facilitating the Li2CO3 Decomposition for Cathode Lithium Compensation Agent

The active lithium loss of lithium-ion batteries can be well addressed by adding a cathode lithium compensation agent. Due to the poor conductivity and electrochemical activity, lithium carbonate (Li2CO3) is not considered as a candidate. Herein, an effective cathode lithium compensation agent, the recrystallized Li2CO3 combined with large specific surface area disordered porous carbon (R-LCO@SPC) is prepared. The screened SPC makes it easier for nano-sized Li2CO3 to adsorb and decompose on carbon substrate, meantime, exposing plenty of catalytic active sites of C═O, which can significantly improve the electrochemical activity and conductivity of Li2CO3, thus greatly reducing the decomposition potential of Li2CO3 (4.0 V) and releasing high irreversible capacity (580 mAh g-1) compared to the unmodified Li2CO3 (nearly no capacity above 4.6 V). Meantime, the Li2CO3 can disappear completely without any by-product after the initial cycle accompanied by partially dissolved in electrolyte, optimizing the composition of SEI. The resultant lithium compensation agent applied to LMFP//graphite full cell exhibits a 19.1% increase in energy density, enhancing the rate and cycling performance, demonstrating great practical applications potential in high energy density lithium-ion batteries.

Self-Adaptive Graphdiyne/Sn Interface for High-Performance Sodium Storage

Efficiently reconciling the substantial volume strain with maintaining the stabilities of both interfacial protection and three-dimensional (3D) conductive networks is a scientific and technical challenge in developing tin-based anodes for sodium ion storage. To address this issue, a proof-of-concept self-adaptive protection for the Sn anode is designed, taking advantage of the arbitrary substrate growth of graphdiyne. This protective layer, employing a flexible chain doping strategy, combines the benefits of 2D graphdiyne and linear chain structures to achieve 2D mechanical stability, electronic and ion conductions, ion selectivity, adequate elongation, and flexibility. It establishes close contact with the Sn particles and can adapt to dynamic size changes while effectively facilitating both electronic and ion transports. It successfully mitigates the detrimental effects of particle pulverization and coarsening induced by large-volume changes. The as-obtained Sn electrodes demonstrate exceptional stability, enduring 1800 cycles at a high current density of 2.5 A g-1. This strategy promises to address the general issues associated with large-strain electrodes in next-generation of high-energy-density batteries.

Structural Engineering of Anode Materials for Low-Temperature Lithium-Ion Batteries: Mechanisms, Strategies, and Prospects

The severe degradation of electrochemical performance for lithium-ion batteries (LIBs) at low temperatures poses a significant challenge to their practical applications. Consequently, extensive efforts have been contributed to explore novel anode materials with high electronic conductivity and rapid Li+ diffusion kinetics for achieving favorable low-temperature performance of LIBs. Herein, we try to review the recent reports on the synthesis and characterizations of low-temperature anode materials. First, we summarize the underlying mechanisms responsible for the performance degradation of anode materials at subzero temperatures. Second, detailed discussions concerning the key pathways (boosting electronic conductivity, enhancing Li+ diffusion kinetics, and inhibiting lithium dendrite) for improving the low-temperature performance of anode materials are presented. Third, several commonly used low-temperature anode materials are briefly introduced. Fourth, recent progress in the engineering of these low-temperature anode materials is summarized in terms of structural design, morphology control, surface & interface modifications, and multiphase materials. Finally, the challenges that remain to be solved in the field of low-temperature anode materials are discussed. This review was organized to offer valuable insights and guidance for next-generation LIBs with excellent low-temperature electrochemical performance.

The interface engineering and structure design of an alloying-type metal foil anode for lithium ion batteries: a review

An alloying-type metal foil serves as an integrated anode that is distinct from the prevalent powder-casting production of lithium ion batteries (LIBs) and emerging lithium metal batteries (LMBs), and also its energy density and processing technology can be profoundly developed. However, besides their apparent intriguing advantages of a high specific capacity, electrical conductivity, and the ease of formation, metal foil anodes suffer from slow lithiation kinetics, a trade-off between specific capacity and cycle life, and a low initial Coulombic efficiency (ICE) owing to their multi-scaled structural geometry, huge volume change, and induced interfacial issues during the alloying process. In this review, we attempt to present a comprehensive overview on the recent research progress with respect to alloying-type metal foil anodes toward high-energy-density and low-cost LIBs. The failure mechanism of metal foil anodes during lithiation/delithiation and existing challenges are also summarized. Subsequently, the structural design and interface engineering strategies that have witnessed significant achievements are highlighted, which can promote the practical development of LIBs, including artificial SEI, alloying, structural design, and grain refinement. Furthermore, scientific perspectives are proposed to further improve the overall performance and decouple the complex mechanisms in terms of interdisciplinary fields of electrochemistry, metallic materials science, mechanics, and interfacial science, demonstrating that metal foil anode-based LIBs require more research efforts.

Electrochemically Responsive 3D Nanoarchitectures

Responsive nanomaterials are being developed to create new unique functionalities such as switchable colors and adhesive properties or other programmable features in response to external stimuli. While many existing examples rely on changes in temperature, humidity, or pH, this study aims to explore an alternative approach relying on simple electric input signals. More specifically, 3D electrochromic architected microstructures are developed using carbon nanotube-Tin (Sn) composites that can be reconfigured by lithiating Sn with low power electric input (≈50 nanowatts). These microstructures have a continuous, regulated, and non-volatile actuation determined by the extent of the electrochemical lithiation process. In addition, this proposed fabrication process relies only on batch lithographic techniques, enabling the parallel production of thousands of 3D microstructures. Structures with a 30-97% change in open-end area upon actuation are demonstrated and the importance of geometric factors in the response and structural integrity of 3D architected microstructures during electrochemical actuation is highlighted.

N-doped carbon sheets supported P-Fe3O4-MoO2 for freshwater and seawater electrolysis

Electric-driven freshwater/seawater splitting is an attractive and sustainable route to realize the generation of H2 and O2. Molybdenum-based oxides exhibit poor activity toward freshwater/seawater electrolysis. Herein, we adjusted the electronic structure of MoO2 by constructing N-doped carbon sheets supported P-Fe3O4-MoO2 nanosheets (P-Fe3O4-MoO2/NC). P-Fe3O4-MoO2/N-doped carbon sheets were precisely prepared by pyrolysis of Schiff base Fe complex and MoO3 nanosheets through phosphorization. Benefiting from the unique structures of the samples, it required 119/145 mV to drive freshwater/seawater reduction reaction at 10 mA/cm2. P-Fe3O4-MoO2/NC catalysts exhibited superior freshwater/seawater oxidation reactivity with 180/189 mV at 10 mA/cm2 compared with commercial RuO2. The low cell voltages for P-Fe3O4-MoO2/NC were 1.47 and 1.59 V towards freshwater and seawater electrolysis, respectively. Our work might shed light on the structural modulation of Mo-based oxides for enhancing freshwater and seawater electrolysis activity.

Interfacial Modulation of a Self-Sacrificial Synthesized SnO2@Sn Core-Shell Heterostructure Anode toward High-Capacity Reversible Li+ Storage

Sn-based anodes are promising high-capacity anode materials for low-cost lithium ion batteries. Unfortunately, their development is generally restricted by rapid capacity fading resulting from large volume expansion and the corresponding structural failure of the solid electrolyte interphase (SEI) during the lithiation/delithiation process. Herein, heterostructural core-shell SnO2-layer-wrapped Sn nanoparticles embedded in a porous conductive nitrogen-doped carbon (SOWSH@PCNC) are proposed. In this design, the self-sacrificial Zn template from the precursors is used as the pore former, and the LiF-Li3N-rich SEI modulation layer is motivated to average uniform Li+ flux against local excessive lithiation. Meanwhile, both the chemically active nitrogen sites and the heterojunction interfaces within SnO2@Sn are implanted as electronic/ionic promoters to facilitate fast reaction kinetics. Consequently, the as-converted SOWSH@PCNC electrodes demonstrate a significantly boosted Li+ capacity of 961 mA h g-1 at 200 mA g-1 and excellent cycling stability with a low capacity decaying rate of 0.071% after 400 cycles at 500 mA g-1, suggesting their great promise as an anode material in high-performance lithium ion batteries.

Tendency Regulation of Competing Reactions Toward Highly Reversible Tin Anode for Aqueous Alkaline Batteries

Investigating dendrite-free stripping/plating anodes is highly significant for advancing the practical application of aqueous alkaline batteries. Sn has been identified as a promising candidate for anode material, but its deposition/dissolution efficiency is hindered by the strong electrostatic repulsion between Sn(OH)3 - and the substrate. Herein, this work constructs a nondense copper layer which serves as stannophile and hydrogen evolution inhibitor to adjust the tendency of competing reactions on Sn foil surface, thus achieving a highly reversible Sn anode. The interactions between the deposited Sn and the substrates are also strengthened to prevent shedding. Notably, the ratio of Sn redox reaction is significantly boosted from ≈20% to ≈100%, which results in outstanding cycling stability over 560 h at 10 mA cm-2 . A Sn//Ni(OH)2 battery device is also demonstrated with capacities from 0.94 to 22.4 mA h cm-2 and maximum stability of 1800 cycles.

Toward the Long-Term Stability of Cobalt Benzoate Confined Highly Dispersed PtCo Alloy Supported on a Nitrogen-Doped Carbon Nanosheet/Fe3C Nanoparticle Hybrid as a Multifunctional Catalyst for Zinc-Air Batteries

This work reports a new type of platinum-based heterostructural electrode catalyst that highly dispersed PtCo alloy nanoparticles (NPs) confined in cobalt benzoate (Co-BA) nanowires are supported on a nitrogen-doped ultra-thin carbon nanosheet/Fe₃C hybrid (PtCo@Co-BA-Fe₃C/NC) to show high electrochemical activity and long-term stability. One-dimensional Co-BA nanowires could alleviate the shedding and agglomeration of PtCo alloy NPs during the reaction so as to achieve satisfactory long-term durability. Moreover, the synergistic effect at the interface optimizes the surface electronic structure and prominently accelerates the electrochemical kinetics. The oxygen reduction reaction half-wave potential is 0.923 V, and the oxygen evolution reaction under the condition of 10 mA•cm^-2 is 1.48 V. Higher power density (263.12 mW•cm^-2), narrowed voltage gap (0.49 V), and specific capacity (808.5 mAh•g^-1) for PtCo@Co-BA-Fe₃C/NC in Zn-air batteries are achieved with long-term cycling measurements over 776 h, which is obviously better than the Pt/C + RuO₂ catalyst. The interfacial electronic interaction of PtCo@Co-BA-Fe₃C/NC is investigated, which can accelerate electron transfer from Fe to Pt. Density functional theory calculations also indicate that the interfacial potential regulates the binding energies of the intermediates to achieve the best performance.

Recent advances in zinc-air batteries: self-standing inorganic nanoporous metal films as air cathodes

Zinc-air batteries (ZABs) have promising prospects as next-generation electrochemical energy systems due to their high safety, high power density, environmental friendliness, and low cost. However, the air cathodes used in ZABs still face many challenges, such as the low catalytic activity and poor stability of carbon-based materials at high current density/voltage. To achieve high activity and stability of rechargeable ZABs, chemically and electrochemically stable air cathodes with bifunctional oxygen reduction reaction (ORR)/oxygen evolution reaction (OER) activity, fast reaction rate with low platinum group metal (PGM) loading or PGM-free materials are required, which are difficult to achieve with common electrocatalysts. Meanwhile, inorganic nanoporous metal films (INMFs) have many advantages as self-standing air cathodes, such as high activity and stability for both the ORR/OER under highly alkaline conditions. The high surface area, three-dimensional channels, and porous structure with controllable crystal growth facet/direction make INMFs an ideal candidate as air cathodes for ZABs. In this review, we first revisit some critical descriptors to assess the performance of ZABs, and recommend the standard test and reported manner. We then summarize the recent progress of low-Pt, low-Pd, and PGM-free-based materials as air cathodes with low/non-PGM loading for rechargeable ZABs. The structure-composition-performance relationship between INMFs and ZABs is discussed in-depth. Finally, we provide our perspectives on the further development of INMFs towards rechargeable ZABs, as well as current issues that need to be addressed. This work will not only attract researchers' attention and guide them to assess and report the performance of ZABs more accurately, but also stimulate more innovative strategies to drive the practical application of INMFS for ZABs and other energy-related technologies.

Mass-producible in-situ amorphous solid/electrolyte interface with high ionic conductivity for long-cycling aqueous Zn-ion batteries

Although aqueous Zn-ion batteries (aZIBs) have garnered significant attention, they are yet to be commercialized due to severe corrosion and dendrite growth on Zn anodes. In this work, an artificial solid-electrolyte interface (SEI) with amorphous structure was created in-situ on the anode by immersing Zn foil in ethylene diamine tetra(methylene phosphonic acid) sodium (EDTMPNA5) liquid. This facile and effective method provides the possibility for Zn anode protection in large-scale applications. Experimental results, combined with theoretical calculations, indicate that the artificial SEI remains intact and adheres tightly to the Zn substrate. The negatively-charged phosphonic acid groups and disordered inner structure offer adequate sites for rapid Zn²⁺ transference and facilitate [Zn(H₂O)₆]²⁺ desolvation during charging/discharging. Due to the synergistic effect of the aforementioned advantages, the artificial SEI endows high Coulombic efficiency (CE, 99.75%) and smooth Zn deposition/stripping under the SEI. The symmetric cell exhibits a long cycling life of over 2400 h with low-voltage hysteresis. Additionally, full cells with MVO cathodes demonstrate the superiority of the modified anodes. This work provides insight into the design of in-situ artificial SEI on the Zn anode and self-discharge suppression to expedite the practical application of aZIBs.

Precise Construction of Sn/C Composite Membrane with Graphene-Like Sn-in-Carbon Structural Units toward Hyperstable Anode for Lithium Storage

A new-type binder-free Sn/C composite membrane with densely stacked Sn-in-carbon nanosheets was prepared by vacuum-induced self-assembly of graphene-like Sn alkoxide and following in situ thermal conversion. The successful implementation of this rational strategy is based on the controllable synthesis of graphene-like Sn alkoxide by using Na-citrate with the critical inhibitory effect on polycondensation of Sn alkoxide along the a and b directions. Density functional theory calculations reveal that graphene-like Sn alkoxide can be formed under the joint action of oriented densification along the c axis and continuous growth along the a and b directions. The Sn/C composite membrane constructed by graphene-like Sn-in-carbon nanosheets can effectively buffer volume fluctuation of inlaid Sn during cycling and much enhance the kinetics of Li⁺ diffusion and charge transfer with the developed ion/electron transmission paths. After temperature-controlled structure optimization, Sn/C composite membrane displays extraordinary Li storage behaviors, including reversible half-cell capacities up to 972.5 mAh g^-1 at a density of 1 A g^-1 for 200 cycles, 885.5/729.3 mAh g^-1 over 1000 cycles at large current densities of 2/4 A g^-1, and terrific practicability with reliable full-cell capacities of 789.9/582.9 mAh g^-1 up to 200 cycles under 1/4 A g^-1. It is worthy of noting that this strategy may open up new opportunities to fabricate advanced membrane materials and construct hyperstable self-supporting anodes in lithium ion batteries.

Bifunctional structure modulation of Sb-based sulfide for boosting fast and high-capacity sodium storage

A novel bimetallic sulfide CrSbS3 with both high sodium storage capacity and good rate performance is synthesized by introducing Cr atoms into the Sb2S3 structure.

Low-Dimensional Nanomaterial Systems Formed by IVA Group Elements Allow Energy Conversion Materials to Flourish

In response to the exhaustion of traditional energy, green and efficient energy conversion has attracted growing attention. The IVA group elements, especially carbon, are widely distributed and stable in the earth’s crust, and have received a lot of attention from scientists. The low-dimensional structures composed of IVA group elements have special energy band structure and electrical properties, which allow them to show more excellent performance in the fields of energy conversion. In recent years, the diversification of synthesis and optimization of properties of IVA group elements low-dimensional nanomaterials (IVA-LD) contributed to the flourishing development of related fields. This paper reviews the properties and synthesis methods of IVA-LD for energy conversion devices, as well as their current applications in major fields such as ion battery, moisture electricity generation, and solar-driven evaporation. Finally, the prospects and challenges faced by the IVA-LD in the field of energy conversion are discussed.

Construction of a High-Stability and Low-Nucleation-Barrier Cu3Sn Alloy Layer on Carbon Paper for Dendrite-Free Li Metal Deposition

The construction of three-dimensional lithiophilic hosts is one of the most effective approaches for achieving the uniform nucleation and alleviating the volume changes of the Li metal. Unfortunately, some lithiophilic materials suffer from severe mechanical degradation resulting from the large volume expansion during lithiation, which causes a heterogeneous Li deposition. Herein, a low-nucleation-barrier Cu₃Sn alloy layer on a carbon paper (Cu₃Sn/CP) is constructed by a facile co-electrodeposition method for the Li anode framework. Density functional theory calculations show that the Cu₃Sn alloy has a higher binding energy (-2.31 eV) than pure Sn (-1.97 eV) due to the electron-deficient state of Sn in the alloy phase, which enables the lithiophilic Sn to have increased affinity for Li. Additionally, the uniformly distributed Cu particles can evenly disperse the electric field on the surface of the carbon fiber and act as a "metal barrier" to inhibit the volume expansion of the Sn particles during lithiation, thereby enhancing the electrochemical stability of the alloy modification layer. As a result, the Cu₃Sn/CP anode framework exhibits an exceptionally low nucleation overpotential (∼10 mV), a high and steady Coulombic efficiency (>98.5% for more than 200 cycles), and a long lifespan up to 1150 h. The full cells with LiFePO₄ as a cathode show favorable cycling performance at 1 C with a capacity retention rate of 95.2%. The construction of the Cu₃Sn alloy layer in this work sheds light on the design of a high-stability lithiophilic host for the dendrite-free Li metal anode.

CO2 Bubble-Assisted Pt Exposure in PtFeNi Porous Film for High-Performance Zinc-Air Battery

Fine-tuning the exposed active sites of platinum group metal (PGM)-based materials is an efficient way to improve their electrocatalytic performance toward large-scale applications in renewable energy devices such as Zn-air batteries (ZABs). However, traditional synthetic methods trade off durability for the high activity of PGM-based catalysts. Herein, a novel dynamic CO₂-bubble template (DCBT) approach was established to electrochemically fine-tuning the exposed Pt active sites in PtFeNi (PFN) porous films (PFs). Particularly, CO₂ bubbles were intentionally generated as gas-phase templates by methanol electrooxidation. The generation, adsorption, residing, and desorption of CO₂ bubbles on the surface of PFN alloys were explored and controlled by adjusting the frequency of applied triangular-wave voltage. Thereby, the surface morphology and Pt exposure of PFN PFs were controllably regulated by tuning the surface coverage of CO₂ bubbles. Consequently, the Pt_1.1%Fe_8.8%Ni PF with homogeneous nanoporous structure and sufficiently exposed Pt active sites was obtained, showing preeminent activities with a half-wave potential (E_1/2) of 0.87 V and onset overpotential (η_onset) of 288 mV at 10 mA cm^-2 for oxygen reduction and evolution reactions (ORR and OER), respectively, at an ultralow Pt loading of 0.01 mg cm^-2. When tested in ZABs, a high power density of 175.0 mW cm^-2 and a narrow voltage gap of 0.64 V were achieved for the long cycling tests over 500 h (750 cycles), indicating that the proposed approach can efficiently improve the activity of PGM catalysts by fine-tuning the microstructure without compromising the durability.

Rational Design and in-situ Synthesis of Ultra-Thin β-Ni(OH)2 Nanoplates for High Performance All-Solid-State Flexible Supercapacitors

The all-solid-state flexible supercapacitor (AFSC), one of the most flourishing energy storage devices for portable and wearable electronics, attracts substantial attentions due to their high flexibility, compact size, improved safety, and environmental friendliness. Nevertheless, the current AFSCs usually show low energy density, which extremely hinders their practical applications. Herein, ultra-thin β-Ni(OH)₂ nanoplates with thickness of 2.4 ± 0.2 nm are in-situ grown uniformly on Ni foam by one step hydrothermal treatment. Thanks to the ultra-thin nanostructure, β-Ni(OH)₂ nanoplates shows a specific capacitance of 1,452 F g⁻¹ at the scan rate of 3 mV s⁻¹. In addition, the assembled asymmetric AFSC [Ni(OH)₂//Activated carbon] shows a specific capacitance of 198 F g⁻¹. It is worth noting that the energy density of the AFSC can reach 62 Wh kg⁻¹ while keeping a high power density of 1.5 kW kg⁻¹. Furthermore, the fabricated AFSCs exhibit satisfied fatigue behavior and excellent flexibility, and about 82 and 86% of the capacities were retained after 5,000 cycles and folding over 1,500 times, respectively. Two AFSC in series connection can drive the electronic watch and to run stably for 10 min under the bending conditions, showing a great potential for powering portable and wearable electronic devices.