Crystal Facet-Controlled Efficient SnS Photocathodes for High Performance Bias-Free Solar Water Splitting

Origin of the Improved Photoelectrochemical and Photocatalytic Activity in a ZnO-TiO2 Nanohybrid Revealed by Experimental and Density Functional Theory Studies

Heterojunctions of metal oxides have attracted a great deal of attention as photo (electro) catalysts owing to their excellent photoactivity. While multiple fundamental studies have been dedicated to heteroaggregation, self-assembly of oppositely charged particles to obtain heterojunctions for energy applications has been underexplored. Herein, we report the synthesis of ZnO-TiO2 heterojunctions using the electrostatic self-assembly approach. The synthesized ZnO-TiO2 heterojunctions were characterized by using multiple experimental techniques. Density functional theory calculations were conducted to establish the heterojunction formation mechanism and electronic properties. The ZnO-TiO2 nanohybrid was tested for the photodegradation of rhodamine B dye and water splitting applications. The photocatalytic performance of the ZnO-TiO2 nanohybrid is 3.5 times higher than that of bare ZnO. In addition, the heterostructure exhibited an excellent photocurrent density of 2.4 mA cm-2 at a low onset potential during photoelectrochemical oxygen evolution. The performance improvements are attributed to the formation of the type II heterojunction between ZnO and TiO2, which suppresses carrier recombination and enhances carrier transport, boosting the catalytic activity.

Tandem cells for unbiased photoelectrochemical water splitting

Hydrogen is an essential energy carrier which will address the challenges posed by the energy crisis and climate change. Photoelectrochemical water splitting (PEC) is an important method for producing solar-powered hydrogen. The PEC tandem configuration harnesses sunlight as the exclusive energy source to drive both the hydrogen (HER) and oxygen evolution reactions (OER), simultaneously. Therefore, PEC tandem cells have been developed and gained tremendous interest in recent decades. This review describes the current status of the development of tandem cells for unbiased photoelectrochemical water splitting. The basic principles and prerequisites for constructing PEC tandem cells are introduced first. We then review various single photoelectrodes for use in water reduction or oxidation, and highlight the current state-of-the-art discoveries. Second, a close look into recent developments of PEC tandem cells in water splitting is provided. Finally, a perspective on the key challenges and prospects for the development of tandem cells for unbiased PEC water splitting are given.

Renewable formate from sunlight, biomass and carbon dioxide in a photoelectrochemical cell

The sustainable production of chemicals and fuels from abundant solar energy and renewable carbon sources provides a promising route to reduce climate-changing CO₂ emissions and our dependence on fossil resources. Here, we demonstrate solar-powered formate production from readily available biomass wastes and CO₂ feedstocks via photoelectrochemistry. Non-precious NiOOH/α-Fe₂O₃ and Bi/GaN/Si wafer were used as photoanode and photocathode, respectively. Concurrent photoanodic biomass oxidation and photocathodic CO₂ reduction towards formate with high Faradaic efficiencies over 85% were achieved at both photoelectrodes. The integrated biomass-CO₂ photoelectrolysis system reduces the cell voltage by 32% due to the thermodynamically favorable biomass oxidation over conventional water oxidation. Moreover, we show solar-driven formate production with a record-high yield of 23.3 μmol cm^-2 h^-1 as well as high robustness using the hybrid photoelectrode system. The present work opens opportunities for sustainable chemical and fuel production using abundant and renewable resources on earth-sunlight, biomass and CO₂.

An integrated n-Si/BiVO4 photoelectrode with an interfacial bi-layer for unassisted solar water splitting

Integrated n-Si/BiVO4 is one of the most promising candidates for unbiased photoelectrochemical water splitting. However, a direct connection between n-Si and BiVO4 will not attain overall water splitting due to the small band offset as well as the interfacial defects at the n-Si/BiVO4 interface that severely impede carrier separation and transport, limiting the photovoltage generation. This paper describes the design and fabrication of an integrated n-Si/BiVO4 device with enhanced photovoltage extracted from the interfacial bi-layer for unassisted water splitting. An Al2O3/indium tin oxide (ITO) interfacial bi-layer was inserted at the n-Si/BiVO4 interface, which promotes the interfacial carrier transport by enlarging the band offset while healing interfacial defects. When coupled to a separate cathode for hydrogen evolution, spontaneous water splitting could be realized with this n-Si/Al2O3/ITO/BiVO4 tandem anode, with an average solar-to-hydrogen (STH) efficiency of 0.62% for over 1000 hours.

Bi2 S3 -Cu3 BiS3 Mixed Phase Interlayer for High-Performance Cu3 BiS3 -Photocathode for 2.33% Unassisted Solar Water Splitting Efficiency

To realize practical solar hydrogen production, a low-cost photocathode with high photocurrent density and onset potential should be developed. Herein, an efficient and stable overall photoelectrochemical tandem cell is developed with a Cu3 BiS3 -based photocathode. By exploiting the crystallographic similarities between Bi2 S3 and Cu3 BiS3 , a one-step solution process with two sulfur sources is used to prepare the Bi2 S3 -Cu3 BiS3 blended interlayer. The elongated Bi2 S3 -Cu3 BiS3 mixed-phase 1D nanorods atop a planar Cu3 BiS3 film enable a high photocurrent density of 7.8 mA cm-2 at 0 V versus the reversible hydrogen electrode, with an onset potential of 0.9 VRHE . The increased performance over the single-phase Cu3 BiS3 thin-film photocathode is attributed to the enhanced light scattering and charge collection through the unique 1D nanostructure, improved electrical conductivity, and better band alignment with the n-type CdS layer. A solar-to-hydrogen efficiency of 2.33% is achieved under unassisted conditions with a state-of-the-art Mo:BiVO4 photoanode, with excellent stability exceeding 21 h.

Research on the Influence of the Interfacial Properties Between a Cu3 BiS3 Film and an Inx Cd1- x S Buffer Layer for Photoelectrochemical Water Splitting

The ternary compound photovoltaic semiconductor Cu3 BiS3 thin film-based photoelectrode demonstrates a quite promising potential for photoelectrochemical hydrogen evolution. The presented high onset potential of 0.9 VRHE attracts much attention and shows that the Cu3 BiS3 thin films are quite good as an efficient solar water splitting photoelectrode. However, the CdS buffer does not fit the Cu3 BiS3 thin film: the conduction band offset between CdS and Cu3 BiS3 reaches 0.7 eV, and such a high conduction band offset (CBO) significantly increases the interfacial recombination ratio and is the main reason for the relatively low photocurrent of the Cu3 BiS3 /CdS photoelectrode. In this study, the Inx Cd1- x S buffer layer is found to be significantly lowered the CBO of CBS/buffer and that the In incorporation ratio of the buffer influences the CBO value of the CBS/buffer. The Pt-TiO2 /In0.6 Cd0.4 S/Cu3 BiS3 photocathode exhibits an appreciable photocurrent density of ≈12.20 mA cm-2 at 0 VRHE with onset potential of more than 0.9 VRHE , and the ABPE of the Cu3 BiS3 -based photocathode reaches the highest value of 3.13%. By application of the In0.6 Cd0.4 S buffer, the Cu3 BiS3 -BiVO4 tandem cell presents a stable and excellent unbiased STH of 2.57% for over 100 h.