Axial Oxygen Ligands Regulating Electronic and Geometric Structure of Zn-N-C Sites to Boost Oxygen Reduction Reaction

N-regulated three-dimensional turf-like carbon nanosheet loaded with FeCoNi nanoalloys as bifunctional electrocatalysts for durable zinc-air batteries

N-regulated three-dimensional (3D) turf-like carbon material loaded with FeCoNi nanoalloys (F-CNS-CNT), composed of carbon nanotubes (CNT) grown in situ on carbon nanosheets(CNS), was synthesized using a low-temperature solution combustion method and organic compounds rich in pyridinic-N. This distinct structure significantly expands the effective electrochemical surface area, revealing an abundance of active sites and enhancing the mass transfer capability for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). Both experimental observations and theoretical calculations corroborate that the synergy between the FeCoNi nanoalloy and the highly pyridinic N-doped carbon substrate optimizes the adsorption and desorption-free energy of oxygen intermediates, resulting in a remarkable improvement of intrinsic ORR/OER activity. Therefore, the derived F-CNS-CNT electrocatalyst can present a favorable half-wave potential of 0.85 V (ORR) and a lower overpotential of 260 mV (corresponding to a current density of 10 mA cm-2, OER) in alkaline media. Moreover, when employed in the air cathode of a flowable zinc-air battery, the electrocatalyst exhibits exceptional discharge and charge performance, including a high power density of 144.6 mW cm-2, a high specific capacity of 801 mAh g-1, and an impressive cycling stability of 600 cycles at a current density of 10 mA cm-2. Notably, these results markedly surpass those of the commercial catalyst Pt/C + IrO2.

Nitrogen, sulfur co-coordinated iron single-atom catalysts with the optimized electronic structure for highly efficient oxygen reduction in Zn-air battery and fuel cell

Atomically dispersed iron-nitrogen-carbon (FesbndNsbndC) materials have been considered ideal catalysts for the oxygen reduction. Unfortunately, designing and adjusting the electronic structure of single-atom Fe sites to boost the kinetics and activity still faces grand challenges. In this work, the coordination environment engineering is developed to synthesize the FeSA/NSC catalyst with the tailored N, S co-coordinated Fe atomic site (Fe-N3S site). The structural characterizations and theoretical calculations demonstrate that the incorporation of sulfur can optimize the charge distribution of Fe atoms to weaken the adsorption of OH* and facilitate the desorption of OH*, thus leading to enhanced kinetics process and intrinsic activity. As a result, the S-modified FeSA/NSC exhibits outstanding catalytic activity with the half-wave potentials (E1/2) of 0.915 V and 0.797 V, as well as good stability, in alkaline and acidic electrolytes, respectively. Impressively, the excellent performance of FeSA/NSC is further confirmed in Zn-air batteries (ZABs) and fuel cells, with high peak power densities (146 mW cm-2 and 0.259 W cm-2).

Efficient and durable oxygen reduction in alkaline media by doping heteroatomic boron into FeSA-NC catalyst

Despite extensive research has been conducted on atomic dispersion catalysts for various reactions, altering the electronic structure of the central metal to enhance electrochemical reactivity remains a challenging task. Herein, the electrochemical reactivity was considerably enhanced by introducing heteroatomic B to adjust the d-band of single Fe center. In specific, the obtained FeSA-BNC catalyst demonstrated an outstanding ORR performance (E1/2 = 0.87 V) and exhibited greater long-term durability in alkaline media compared to Pt/C. The performance of FeSA-BNC in Zn-air battery was also higher than that of Pt/C. According to theoretical calculations, a downward shift in the d-band center of Fe was induced by introducing B, thereby improving the desorption of intermediates and facilitating the oxygen reduction reaction (ORR).

Electrocatalytic Oxygen Reduction Using Metastable Zirconium Suboxide

Strategies for discovery of high-performance electrocatalysts are important to advance clean energy technologies. Metastable phases such as low temperature or interfacial structures that are difficult to access in bulk may offer such catalytically active surfaces. We report here that the suboxide Zr3O, which is formed at Zr-ZrO2 interfaces but does not appear in the experimental Zr-O phase diagram exhibits outstanding oxygen reduction reaction (ORR) performance surpassing that of benchmark Pt/C and most transition metal-based catalysts. Addition of Fe3C nanoparticles to give a Zr-Zr3O-Fe3C/NC catalyst (NC=nitrogen-doped carbon) gives a half-wave potential (E1/2) of 0.914 V, outperforming Pt/C and showing only a 3 mV decrease after 20,000 electrochemical cycles. A zinc-air battery (ZAB) using this cathode material has a high power density of 241.1 mW cm-2 and remains stable for over 50 days of continuous cycling, demonstrating potential for practical applications. Zr3O demonstrates that interfacial or other phases that are difficult to stabilize may offer new directions for the discovery of high-performance electrocatalysts.

Graphene-supported MN4 single-atom catalysts for multifunctional electrocatalysis enabled by axial Fe tetramer coordination

Multifunctional electrocatalysts for oxygen reduction reaction (ORR), oxygen evolution reaction (OER), and hydrogen evolution reaction (HER) are crucial for development of the key electrochemical energy storage and conversion devices, for which single-atom catalyst (SAC) has present great promises. Very recently, some experimental works showed that structurally well-defined ultra-small transition-metal clusters (such as Fe and Co tetramers, denoted as Fe4 and Co4, respectively), can efficiently modulate the catalytic behavior of SACs by axial coordination. Herein, taking the graphene-supported MN4 SACs as representatives, we theoretically explored the feasibility of realizing multifunctional SACs for ORR, OER and HER by this novel axial coordination engineering. Through extensive first-principles calculations, from 23 candidates, IrN4 decorated with Fe4 (IrN4/Fe4) is identified as the promising trifunctional catalyst with the theoretical overpotential of 0.43, 0.51 and 0.30 V for OER, ORR and HER, respectively. RhN4/Fe4 and CoN4/Fe4 are recognized as potential OER and ORR bifunctional catalysts. In addition, NiN4/Fe4 exhibits the best ORR activity with an overpotential of 0.30 V, far superior to the pristine NiN4 SAC (0.88 V). Electronic structure analyses reveal that the significantly enhanced ORR/OER activity can be ascribed to the orbital and charge redistribution of Ni/Ir active center, resulting from its electronic interaction with Fe4 cluster. This work could stimulate and guide the rational design of graphene-based multifunctional SACs realized by axial coordination of small TM clusters, and provide insights into the modulation mechanism.

In-depth understanding the synergisms of Cu atomic clusters on Cu single atoms for highly effective electrocatalytic oxygen reduction reaction and Zn-Air battery

In this paper, a novel, simple and mild soft template assisted strategy and further carbonization approach has been constructed to the size-tunable preparation of porous Cu-N-C/Surfactant catalysts successfully. Note that the pluronic F127 has a significant influence on the synthesis of porous Cu-N-C/F127 with the atomically dispersed Cu-N4 and adjacent Cu atomic clusters (ACs) than other surfactants owing to their particular non-ionic structure. By combining a series of experimental analysis and density functional theory (DFT) calculations, the synergistic effects between the adjacent Cu ACs and atomically dispersed Cu-N4 are favorable for manipulating the binding energy of O2 adsorption and intermediates desorption at the atomic interface of catalysts, resulting in an excellent electrocatalytic ORR performance with a faster kinetics for Cu-N-C/F127 than those of the Cu-N-C, Cu-N-C/CTAB, Cu-N-C/SDS, and comparable with the commercial Pt/C catalyst. This method not only provides a novel approach for synthesizing highly effective copper based single atom catalysts toward ORR, but also offers an in-depth understanding of the synergisms of adjacent ACs on the Cu single atoms (SAs) for highly effective electrocatalytic ORR and Zn-air Battery.

Axial O Atom-Modulated Fe(III)-N4 Sites for Enhanced Cascade Catalytic 1O2-Induced Tumor Therapy

The rational construction of efficient hypoxia-tolerant nanocatalysts capable of generating singlet oxygen (1O2) without external stimuli is of great importance for tumor therapy. Herein, uniformly dispersed and favorable biosafety profile graphitic carbon nitride quantum dots immobilized with Fe-N4 moieties modulated by axial O atom (denoted as O-Fe-N4) are developed for converting H2O2 into 1O2 via Russell reaction, without introducing external energy. Notably, O-Fe-N4 performs two interconnected catalytic properties: glutathione oxidase-mimic activity to provide substrate for subsequent 1O2 generation, avoiding the blunting anticancer efficacy by glutathione. The O-Fe-N4 catalyst demonstrates a specific activity of 79.58 U mg-1 at pH 6.2, outperforming the most reported Fe-N4 catalysts. Density functional theory calculations demonstrate that the axial O atom can effectively modulate the relative position and electron affinity between Fe and N, lowering the activation energy, strengthening the selectivity, and thus facilitating the Russell-type reaction. The gratifying enzymatic activity stemming from the well-defined Fe-N/O structure can inhibit tumor proliferation by efficiently downregulating glutathione peroxidase 4 activity and inducing lipid peroxidation. Altogether, the O-Fe-N4 catalyst not only represents an efficient platform for self-cascaded catalysis to address the limitations of 1O2-involved cancer treatment but also provides a paradigm to enhance the performance of the Fe-N4 catalyst.

Highly coordinative molecular cobalt-phthalocyanine electrocatalyst on an oxidized single-walled carbon nanotube for efficient hydrogen peroxide production

H2O2 production via the two-electron oxygen reduction reaction (2e- ORR) offers a potential alternative to the current anthraquinone method owing to its efficiency and environmental friendliness. However, it is necessary to determine the structures of electrocatalysts with cost-effectiveness and high efficiency for future industrialization demand. Herein, a supramolecular catalyst composed of cobalt-phthalocyanine on a near-monodispersed and oxidized single-walled carbon nanotube (CoPc/o-SWCNT) was synthesized via a solution self-assembly method for catalyzing the 2e- ORR for H2O2 electrosynthesis. Benefiting from the enhanced intermolecular interaction by introducing oxygen functional groups on o-SWCNTs, the oxidation states of single-atom Co sites were tuned via the formation of two extra Co-O bonds. Coupled with structural characterizations, density-functional theory (DFT) calculations reveal that the depressed d-band center of the Co site regulated by two axially-bridged O atoms gives rise to a suitable binding strength of oxygen intermediates (*OOH) to favor the 2e- ORR. Thus, the CoPc-6wt%/o-SWCNT-2 catalyst with optimized synthetic parameters delivers competitive 2e- ORR performance for H2O2 electrosynthesis in a neutral electrolyte (pH = 7), including enhanced H2O2 generation, satisfactory molar selectivity of ∼83-95% and long-period stability (75 h) in H-cell measurement. Moreover, it could also be boosted to show a high current of 45 mA cm-2, recorded turnover frequency of 25.3 ± 0.5 s-1 and maximum H2O2 production rate of 5.85 mol g-1 h-1 with a continuous H2O2 accumulation of 1.2 wt% in a flow-cell device, which outperformed most of the reported neutral-selective nonprecious metal single-atom catalysts.

High quality bifunctional cathode for rechargeable zinc-air batteries using N-doped carbon nanotubes constrained CoFe alloy

Building efficient and stable bifunctional electrocatalysts toward oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) is crucial for the advancement of rechargeable zinc-air batteries (ZABs). Here, a convenient in situ strategy is reported to controllably encapsulate CoFe alloy nanoparticles within N-doped carbon nanotubes (CoFe@NCNT). The abundant Co(Fe)-Nx active sites and the synergistic interaction between CoFe alloys and carbon nanotubes facilitate mass transfer and interfacial charge transfer, resulting in excellent dual functional electrocatalytic activity of OER/ORR with minor potential difference (ΔE = 0.73 V). Thus, the corresponding rechargeable ZAB displays high power density (194 mW cm-2), excellent specific capacity (795 mAh gZn-1), and favorable stability (900 cycles@5 mA cm-2). This work provides an approach for establishing low-cost bultifunctional electrocatalysts with excellent performance of non-noble metal nanoalloys.

Anchoring covalent organic polymers on supports with tunable functional groups boosting the oxygen reduction performance under pH-universal conditions

Iron phthalocyanine (FePc) is an attractive nonprecious metal candidate for electrocatalytic oxygen reduction reaction (ORR). However, its low catalytic performance under acidic and neutral conditions limits its practical application. Herein, the FePc-based covalent organic polymers (COPFePc) polymerized in situ on the functionalized multiwalled carbon nanotubes (R-MWCNT) containing different electron-withdrawing or electron-donating groups (COPFePc/R-MWCNT, R = COOH, OH or NH2) were synthesized for ORR. Among them, COPFePc/COOH-MWCNT exhibited the best ORR performance under pH-universal conditions (acidic, neutral, and alkaline). Density-functional theory (DFT) calculations demonstrate that the electron-withdrawing or electron-donating effect of the functional groups in COPFePc/R-MWCNT causes charge redistribution of the active center Fe. The COOH functional group with an electron-withdrawing ability shifts the d-band center of Fe away from the Fermi energy level and reduces the binding strength of oxygen-containing intermediates, accelerating the ORR kinetics and optimizing the catalytic activity.

Sulfur-bridge ligands altering the microenvironment of single-atom CoN3S sites to boost the oxygen reduction reaction

We report here an asymmetric N,S-coordinated cobalt-based single-atom catalyst with sulfur (S)-bridge ligands (Co-N/S-C) for the oxygen reduction reaction (ORR). The Co-N/S-C exhibits a half-wave potential (E1/2) of 0.908 V versus RHE, outperforming most state-of-the-art ORR catalysts. Theoretical calculations indicate that the CoN3SC10-S moiety facilitates the ORR kinetics by optimizing the adsorption of intermediates. This work provides new insights into the design of single-atom catalysts for electrocatalysis through heteroatom-bridge ligand engineering.

Ligand-assisted formation of mesoporous Zn-N-C to realize superior catalytic activity in solvent-free CO2 cycloaddition reactions

Mesoporous nitrogen-doped carbon-anchored single atom Zn was synthesized through etching of ZIF-8 with 1,10-phenanthroline and subsequent pyrolysis based on the Kirkendall effect. The abundant pores and increased surface area promote CO2 adsorption and mass transfer, thus significantly improving the catalytic activity in solvent-free cycloaddition of epoxides with CO2.

General Pyrolysis for High-Loading Transition Metal Single Atoms on 2D-Nitro-Oxygeneous Carbon as Efficient ORR Electrocatalysts

Single-atom catalysts (SACs) possess the potential to involve the merits of both homogeneous and heterogeneous catalysts altogether and thus have gained considerable attention. However, the large-scale synthesis of SACs with rich isolate-metal sites by simple and low-cost strategies has remained challenging. In this work, we report a facile one-step pyrolysis that automatically produces SACs with high metal loading (5.2-15.9 wt %) supported on two-dimensional nitro-oxygenated carbon (M1-2D-NOC) without using any solvents and sacrificial templates. The method is also generic to various transition metals and can be scaled up to several grams based on the capacity of the containers and furnaces. The high density of active sites with N/O coordination geometry endows them with impressive catalytic activities and stability, as demonstrated in the oxygen reduction reaction (ORR). For example, Fe1-2D-NOC exhibits an onset potential of 0.985 V vs RHE, a half-wave potential of 0.826 V, and a Tafel slope of -40.860 mV/dec. Combining the theoretical and experimental studies, the high ORR activity could be attributed its unique FeO-N3O structure, which facilitates effective charge transfer between the surface and the intermediates along the reaction, and uniform dispersion of this active site on thin 2D nanocarbon supports that maximize the exposure to the reactants.

Atomically Dispersed Dual-Metal ORR Catalyst with Hierarchical Porous Structure for Zn-Air Batteries

The metal-nitrogen-carbon (M-N-C)-based catalysts are promising to replace PGM (platinum group metal) to accelerate oxygen reduction reaction due to their excellent electrocatalytic performance. However, the inferior intrinsic activity and poor active site density confining further improvement in their performance. Modulating the electronic structure and reasonably designing the pore structure are widely acknowledged effective strategies to boost the activity of the M-N-C catalysts. However, it is a great challenge to form abundant pores to regulate the electronic structure via the facile method. Herein, a hierarchical, porous dual-atom catalyst FeNi-NPC-1000 has been architectured by the Na2CO3 template method and bimetallic doping modification strategy. Benefitting from the optimized pore and electronic structure, the as-prepared FeNi-NPC-1000 possesses a high specific surface area (1412.8 m2 g-1) and improved ORR activity (E1/2 = 0.877 V vs RHE), which is superior to that of Pt/C (E1/2 = 0.867 V vs RHE). With the evidence of AC-STEM, XAS, and DFT, the FeNi-N8-C moiety is proven to be the key active site to realize high-efficiency ORR catalysis. When assembled it as an air cathode of ZABs, FeNi-NPC-1000 displays superior discharge performance (Pmax = 367.1 mW cm-2) and a stable battery long-life. This article will provide a new strategy for designing dual-metal atomic catalysts applied in metal-air batteries.