Biomass Oxidation: Formyl CH Bond Activation by the Surface Lattice Oxygen of Regenerative CuO Nanoleaves

Characterization of phosphate modified red mud-based composite materials and study on heavy metal adsorption

In this paper, Bayer red mud (RM) and lotus leaf powder (LL) were used as the main materials, and KH2PO4 was added to modify the material. Under the condition of high-temperature carbonization, RMLL was prepared and phosphate modified red mud matrix composite (PRMLL) was prepared based on KH2PO4 modification, which can effectively remove Pb2+ from water. The optimum preparation and application conditions were determined through orthogonal experiment: dosage 0.1g, ratio 1:1, and temperature 600 °C. The effects of pH, dosage, and initial concentration on the adsorption of Pb2+ were studied. The pseudo-first-order, pseudo-second-order, and Elovich kinetic models were fitted to the experimental data. It was found that RMLL and PRMLL were more consistent with the pseudo-second-order kinetic model and chemisorption. Langmuir, Freundlich, Timkin, and Dubinin-Radushkevich isothermal adsorption models were used to fit the experimental data. It was found that RMLL and PRMLL were more consistent with Langmuir model. In addition, the maximum adsorption capacity of RMLL and PRMLL was 188.1 mg/g and 213.4 mg/g, respectively. It is larger than the adsorption capacity of their monomers. Therefore, the use of RMLL and PRMLL as the removal of Pb2+ from water is a potential application material.

Electrocatalytic CuBr@CuO nanoparticles based salivary glucose probes

Highly electrocatalytic cuprous halide/copper oxide nanoparticles (CuX@CunO NPs; X = Cl, Br or I; n = 1 or 2) have been fabricated on copper foils for sensitive detection of glucose. Formation of CuX@Cu_nO NPs involves two steps- in situ electrochemical deposition of CuX on the foil and then conversion of CuX to Cu_nO. The deposited CuX converts to Cu_nO, leading to the generation of abundant oxygen vacancies in the CuO lattice, enhancing the number of catalytically active sites, and improving the charge transfer efficiency. Among the as-prepared electrodes, CuBr@CuO NP ones provide the highest electrocatalytic activity toward the oxidation of glucose. The electrode provides electrocatalytic activity toward the oxidation of glucose at a low overpotential of 0.25 V (vs. SCE), which is lower than that (0.40 V) of unmodified copper electrodes. The generated anodic current is proportional to glucose concentration in an alkaline medium, with a good linear range from 5.0 μM to 3.51 mM (R² = 0.995). Its reliability has been validated by detecting the glucose concentration in saliva samples at different time intervals after a meal. The results are in good correlation with the blood glucose level determined by using a commercial blood glucose meter. Our CuBr@CuO NP electrode possesses great potential for monitoring salivary glucose to achieve the purpose of noninvasive glucose monitoring for patients with diabetes in the future.

Synthesis of a Gold-Metal Oxide Core-Satellite Nanostructure for In Situ SERS Study of CuO-Catalyzed Photooxidation

This work reports on an assembling-calcining method for preparing gold-metal oxide core-satellite nanostructures, which enable surface-enhanced Raman spectroscopic detection of chemical reactions on metal oxide nanoparticles. By using the nanostructure, we study the photooxidation of Si-H catalyzed by CuO nanoparticles. As evidenced by the in situ spectroscopic results, oxygen vacancies of CuO are found to be very active sites for oxygen activation, and hydroxide radicals (*OH) adsorbed at the catalytic sites are likely to be the reactive intermediates that trigger the conversion from silanes into the corresponding silanols. According to our finding, oxygen vacancy-rich CuO catalysts are confirmed to be of both high activity and selectivity in photooxidation of various silanes.