A Titanium-Doped SiOxPassivation Layer for Greatly Enhanced Performance of a Hematite-Based Photoelectrochemical System

Ge-Doped Hematite with FeCoNi-Bi as Cocatalyst for High-Performing Photoelectrochemical Water Splitting

Hematite is a promising photoanode material for photoelectrochemical water-splitting technology. However, the low current density associated with the low conductivity, low charge carrier mobility, and poor oxygen evolution catalytic activity is a challenging issue for the material. In this study, the challenge is addressed by introducing Germanium (Ge) doping, coupled with the use of FeCoNi-Bi as a co-catalyst. Ge doping not only increases the conductivity and charge carrier concentration of the hematite photoanode, but also induces nanopores, thereby expanding its electrochemical reactive surface area to facilitate the oxygen evolution reaction. In the meantime, the FeCoNi-Bi cocatalyst electrodeposited onto the surface of Ge-doped hematite, improves the oxygen evolution reaction performance. As a result, the obtained photoanode achieves a photocurrent density of 2.31 mA cm-2 at 1.23 VRHE, which is three times higher than that of hematite (0.72 mA cm-2). Moreover, a new analytical method is introduced to scrutinize both the positive and negative effects of Ge doping and FeCoNi-Bi cocatalyst on the photoanode performance by decoupling the photoelectrochemical process steps. Overall, this study not only enhances the performance of hematite photoanodes but also guides their rational design and systematic assessment.

Value addition of MXenes as photo-/electrocatalysts in water splitting for sustainable hydrogen production

The energy transition from fossil fuel-based to renewable energy is a global agenda. At present, a major concern in the green hydrogen economy is the demand for clean fuels and non-noble materials to produce hydrogen through water splitting. Researchers are focusing on addressing this concern with the help of the development of appropriate non-noble-based photo-/electrocatalytic materials. A new class of two-dimensional materials, MXenes, have recently shown tremendous potential for water splitting to produce H2via a photoelectrochemical process. The unique properties of emerging 2D MXene materials, such as hydrophilic surface functionalities, higher surface-to-volume ratios, and inherent flexibility, present these materials as appropriate photo-/electrocatalytic materials. Unique value addition and innovative strategies such as the introduction of end-group modification, heterojunctions, and nanostructure engineering have shown the potential of MXene materials as emerging photo-/electrocatalysts for water splitting. When integrated with conventional noble metal catalysts, MXene-based catalysts demonstrated a lower overpotential for hydrogen and oxygen evolution reactions and a remarkable boost in performance for enhanced H2 production rates surpassing those of pristine noble metal-based catalysts. These promote future perspectives for the utilization of chemically synthesized MXenes as alternative photo-/electrocatalysts. Future research direction should focus on MXene synthesis and utilization for surface modification, composite formation, stabilization, and optimization in synthesis methods and post-synthesis treatments. This review highlights the progress in the understanding of fundamental mechanisms and issues associated with water splitting, influencing factors of MXenes, their value addition role, and application strategies for water splitting, including performance, challenges, and outlook of MXene-based photo-/electrocatalysts, in the last five years.

Single Crystalline α-Fe2O3 Nanosheets with Improved PEC Performance for Water Splitting

We report the photoelectrochemical (PEC) performance of a densely grown single crystalline hematite (α-Fe2O3) nanosheet photoanode for water splitting. Unlike expensive ITO/FTO substrates, the sheets were grown on a piece of pure Fe through controlled thermal oxidation, which is a facile low cost and one-step synthesis route. The sheets grow with a widest surface parallel to basal plane (0001). Iron oxide formed on Fe consisting of layer structure α-Fe2O3-Fe3O4-Fe is elucidated from GIXRD and correlated to spectral features observed in Raman and UV-vis spectroscopy. The top α-Fe2O3 nanosheet layer serves as a photoanode, whereas the conducting Fe3O4 layer serves to transport photogenerated electrons to the counter electrode through its back contact. Time-resolved photoluminescence (TRPL) measurements revealed significantly prolonged carrier lifetime compared to that of bulk. Compared to the thin film of α-Fe2O3 grown on the FTO substrate, ∼3 times higher photocurrent density (0.33 mA cm-2 at 1.23 VRHE) was achieved in the nanosheet sample under solar simulated AM 1.5 G illumination. The sample shows a bandgap of 2.1 eV and n-type conductivity with carrier density 9.59 × 1017 cm-3. Electrochemical impedance spectroscopy (EIS) measurements reveal enhanced charge transport properties. The results suggest that nanosheets synthesized by the simple method yield far better PEC performance than the thin film on the FTO substrate. The anodic shifts of flat band potential, delayed electron-hole recombination, and growth direction parallel to the highly conducting basal plane (0001) being some of the contributing factors to the higher photocurrent observed in the NS photoanode are discussed. Characterizations carried out before and after the PEC reaction show excellent stability of the nanosheets in an alkaline electrochemical environment.

Boosting Charge Transfer Efficiency by Nanofragment MXene for Efficient Photoelectrochemical Water Splitting of NiFe(OH)x Co-Catalyzed Hematite

The use of oxygen evolution co-catalysts (OECs) with hematite photoanodes has received much attention because of the potential to reduce surface charge recombination. However, the low surface charge transfer and bulk charge separation rate of hematite are not improved by decorating with OECs, and the intrinsic drawbacks of hematite still limit efficient photoelectrochemical (PEC) water splitting. Here, we successfully overcame the sluggish oxygen evolution reaction performance of hematite for water splitting by inserting zero-dimensional (0D) nanofragmented MXene (NFMX) as a hole transport material between the hematite and the OEC. The 0D NFMX was fabricated from two-dimensional (2D) MXene sheets and deposited onto the surface of a three-dimensional (3D) hematite photoanode via a centrifuge-assisted method without altering the inherent performance of the 2D MXene sheets. Among many OECs, NiFe(OH)x was selected as the OEC to improve hematite PEC performance in our system because of its efficient charge transport behavior and high stability. Because of the great synergy between NFMX and NiFe(OH)x, NiFe(OH)x/NFMX/Fe2O3 achieved a maximum photocurrent density of 3.09 mA cm-2 at 1.23 VRHE, which is 2.78-fold higher than that of α-Fe2O3 (1.11 mA cm-2). Furthermore, the poor stability of MXene in an aqueous solution for water splitting was resolved by uniformly coating it with NiFe(OH)x, after which it showed outstanding stability for 60 h at 1.23 VRHE. This study demonstrates the successful use of NFMX as a hole transport material combined with an OEC for highly efficient water splitting.

Sn-Controlled Co-Doped Hematite for Efficient Solar-Assisted Chargeable Zn-Air Batteries

The photoelectrochemical performance of a co-doped hematite photoanode might be hindered due to the unintentionally diffused Sn from a fluorine-doped tin oxide (FTO) substrate during the high-temperature annealing process by providing an increased number of recombination centers and structural disorder. We employed a two-step annealing process to manipulate the Sn concentration in co-doped hematite. The Sn content [Sn/(Sn + Fe)] of a two-step annealing sample decreased to 1.8 from 6.9% of a one-step annealing sample. Si and Sn co-doped hematite with the reduced Sn content exhibited less structural disorder and improved charge transport ability to achieve a 3.0 mA cm^-2 photocurrent density at 1.23 V_RHE, which was 1.3-fold higher than that of the reference Si and Sn co-doped Fe₂O₃ (2.3 mA cm^-2). By decorating with the efficient co-catalyst NiFe(OH)_x, a maximum photocurrent density of 3.57 mA cm^-2 was achieved. We further confirmed that the high charging potential and poor cyclability of the zinc-air battery could be dramatically improved by assembling the optimized, stable, and low-cost hematite photocatalyst with excellent OER performance as a substitute for expensive Ir/C in the solar-assisted chargeable battery. This study demonstrates the significance of manipulating the unintentionally diffused Sn content diffused from FTO to maximize the OER performance of the co-doped hematite.

Improving Photocatalytic Performance Using Nanopillars and Micropillars

A recent research emphasis has been placed on the development of highly crystallized nanostructures as a useful technology for many photocatalytic applications. With the unique construction of semiconductor transition metal oxide nanostructures in the form of nanopillars—artificially designed pillar-shaped structures grouped together in lattice-type arrays—the surface area for photocatalytic potential is increased and further enhanced through the introduction of dopants. This short review summarizes the work on improving the efficiency of photocatalyst nanopillars through increased surface area and doping within the applications of water splitting, removal of organic pollutants from the environment, photoswitching, soot oxidation, and photothermalization.

Hematite Photoanode with Complex Nanoarchitecture Providing Tunable Gradient Doping and Low Onset Potential for Photoelectrochemical Water Splitting

Over the past years, α-Fe₂ O₃ (hematite) has re-emerged as a promising photoanode material in photoelectrochemical (PEC) water splitting. In spite of considerable success in obtaining relatively high solar conversion efficiency, the main drawbacks hindering practical application of hematite are its intrinsically hampered charge transport and sluggish oxygen evolution reaction (OER) kinetics on the photoelectrode surface. In the present work, we report a strategy that synergistically addresses both of these critical limitations. Our approach is based on three key features that are applied simultaneously: i) a careful nanostructuring of the hematite photoanode in the form of nanorods, ii) doping of hematite by Sn⁴⁺ ions using a controlled gradient, and iii) surface decoration of hematite by a new class of layered double hydroxide (LDH) OER co-catalysts based on Zn-Co LDH. All three interconnected forms of functionalization result in an extraordinary cathodic shift of the photocurrent onset potential by more than 300 mV and a PEC performance that reaches a photocurrent density of 2.00 mA cm^-2 at 1.50 V vs. the reversible hydrogen electrode.