Thiourea-Isocyanate-Based Covalent Organic Frameworks with Tunable Surface Charge and Surface Area for Methylene Blue and Methyl Orange Removal from Aqueous Media

A thiourea hexamethylene diisocyanate covalent organic framework (TH COF) was synthesized by adjusting the surface charge and surface area. The surface charge value of TH COF, −3.8 ± 0.5 mV, can be changed to −29.1 ± 0.4 mV by treatment with NaOH (dp-TH) and 17.1 ± 1.0 mV by treatment with HCl (p-TH). Additionally, the surface area of TH COF was 39.3 m2/g, whereas the surface area of dp-TH COF and p-TH COF structures were measured as 41.4 m2/g and 42.5 m2/g, respectively. However, the COF structure had a better adsorption capability with acid and base treatments, e.g., dp-TH COF absorbed 5.5 ± 0.3 mg/g methylene blue (MB) dye, and p-TH COF absorbed 25.9 ± 1.4 mg/g methyl orange (MO) dye from 100 mL 25 ppm aqueous dye solutions, thereby increasing the MB and MO absorption amounts of the TH COF structure. Furthermore, by calculating the distribution, selectivity, and relative selectivity coefficients, the absorption capacity order was determined as dp-TH > TH > p-TH COFs for the MB dye, whereas it was p-TH > TH > dp-TH COFs for the MO dye. Finally, the reusability of dp-TH COF for MB absorption and p-TH COF for MO absorption were investigated. After five repeated uses, dp-TH COF retained 64.6 ± 3.7% of its absorption ability, whereas p-TH COF preserved 79.7 ± 3.2% of its absorption ability relative to the initial absorption amount.

Fabrication of a Covalent Triazine Framework Functional Interlayer for High-Performance Lithium-Sulfur Batteries

The shuttling effect of polysulfides is one of the major problems of lithium-sulfur (Li-S) batteries, which causes rapid capacity fading during cycling. Modification of the commercial separator with a functional interlayer is an effective strategy to address this issue. Herein, we modified the commercial Celgard separator of Li-S batteries with one-dimensional (1D) covalent triazine framework (CTF) and a carbon nanotube (CNT) composite as a functional interlayer. The intertwined CTF/CNT can provide a fast lithium ionic/electronic transport pathway and strong adsorption capability towards polysulfides. The Li-S batteries with the CTF/CNT/Celgard separator delivered a high initial capacity of 1314 mAh g^-1 at 0.1 C and remained at 684 mAh g^-1 after 400 cycles^-1 at 1 C. Theoretical calculation and static-adsorption experiments indicated that the triazine ring in the CTF skeleton possessed strong adsorption capability towards polysulfides. The work described here demonstrates the potential for CTF-based permselective membranes as separators in Li-S batteries.

Eu3+-β-diketone functionalized covalent organic framework hybrid material as a sensitive and rapid response fluorescent sensor for glutaraldehyde

A covalent organic framework (named as TpDq) linked by β-ketoamine was prepared by imine condensation reaction with 1,3,5-triformylphloroglucinol (TFP) and 2,6-diaminoanthraquinone (DAAQ) as building blocks. Via employing a functionalized modification strategy, a new lanthanide complex Eu³⁺-β-diketone functionalized covalent organic framework hybrid material, Eu-TTA@TpDq (TTA = 2-thenoyltrifluoroacetone), has been synthesized. After post-synthetic modification (PSM), the shape and structure of the parent framework is well preserved and the modified material shows remarkable luminescence properties. Based on this, we designed it as a fluorescent probe and tried to use it to sense common aldehydes. The results indicate that Eu-TTA@TpDq exhibits a turn-off response toward glutaraldehyde which can distinguish from other common aldehydes. The fluorescent probe has the advantages of reusability, pH stability (4.50-8.52), fast luminescence response (<1 min) and low detection limit. The linear range of this method was 0-100 μM; the detection limit was 4.55 μM; the relative standard deviation was 2.16%. Furthermore, it has broad application prospect in both practical sensing of glutaraldehyde in water environment and simple detection of glutaraldehyde vapor. In addition, we preliminarily discussed the possible sensing mechanism.

Optimization of Monomer Molecular Structure for Polymer Electrodes Fabricated through in-situ Electro-Polymerization Strategy

In-situ electro-polymerization of redox-active monomers has been proved to be a novel and facile strategy to prepare polymer electrodes with superior electrochemical performance. The monomer molecular structure would have a profound impact on electro-polymerization behavior and thus electrochemical performance. However, this impact is poorly understood and has barely been investigated yet. Herein, three carbazole-based monomers, 9-phenylcarbazole (CB), 1,4-bis(carbazol-9-yl)benzene (DCB), and 2,6-bis(carbazol-9-yl)naphthalene (DCN), were applied to study the above issue systematically and achieve excellent long cycle performance. The monomers were rationally designed with different polymerizable sites and solubilities. It was found that a monomer with increased polymerizable sites and decreased solubility brought about enhanced electrochemical performance. This is because poor solubility could enhance utilization of the monomer for polymerization and more polymerizable sites could lead to a stable crosslinked polymer network after electro-polymerization. DCN with four polymerizable sites and the poorest solubility displayed the best electrochemical performance, which showed stable cycling up to 5000 cycles with high capacity retention of 76.2 % (among the best cycle in the literature). Our work for the first time reveals the relationship between monomer structure and in-situ electro-polymerization behavior. This work could shed light on the structure design/optimization of monomers for high-performance polymer electrodes prepared through in-situ electro-polymerization.

Precise Sub-Angstrom Ion Separation Using Conjugated Microporous Polymer Membranes

Polymer membranes typically possess a broad pore-size distribution that leads to much lower selectivity in ion separation when compared to membranes made of crystalline porous materials; however, they are highly desirable because of their easy processability and low cost. Herein, we demonstrate the fabrication of ion-sieving membranes based on a polycarbazole-type conjugated microporous polymer using an easy to scale-up electropolymerization strategy. The membranes exhibited high uniform sub-nanometer pores and a precisely tunable membrane thickness, yielding a high ion-sieving performance with a sub-1 Å size precision. Both experimental results and molecular simulations suggested that the impressive ion-sieving performance of the CMP membranes originates from their uniform and narrow pore-size distribution.