Epitaxially Grown Heterostructured SrMn 3 O 6− x ‐SrMnO 3 with High‐Valence Mn 3+/4+ for Improved Oxygen Reduction Catalysis

Preparation and Performance of a Cu@PtCu/CNF Oxygen Reduction Catalyst Membrane by Electrospinning

A flexible carbon nanofiber film with high conductivity was prepared by electrospinning, and then Cu was uniformly deposited on the fiber film by pulse electrodeposition to prepare Cu nanocrystal/carbon nanofiber film. Cu@PtCu/carbon nanofiber (Cu@PtCu/CNF) catalytic films were synthesized by in-situ substitution reduction. The Cu@PtCu/CNF catalytic film solves the problem of uneven activity of the catalytic layer and can be directly used as the catalytic layer. The morphology and structure were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Electrochemical test results show that the Cu@PtCu/CNF catalytic films obtained at the chloroplatinic acid concentration of 0.5 mg·mL^-1 (N2) exhibited 2.5 times specific activity when compared with commercial Pt/C catalysts. After 5000 cycles of stability test, the electrochemical surface areas (ECSAs) were still maintained at 80%, and the half-wave potential decreased by 11 mV, which was better than those of commercial Pt/C catalysts.

Synergy in Au-CuO Janus Structure for Catalytic Isopropanol Oxidative Dehydrogenation to Acetone

The controlled oxidation of alcohols to the corresponding ketones or aldehydes via selective cleavage of the β-C-H bond of alcohols under mild conditions still remains a significant challenge. Although the metal/oxide interface is highly active and selective, the interfacial sites fall far behind the demand, due to the large and thick support. Herein, we successfully develop a unique Au-CuO Janus structure (average particle size=3.8 nm) with an ultrathin CuO layer (0.5 nm thickness) via a bimetal in situ activation and separation strategy. The resulting Au-CuO interfacial sites prominently enhance isopropanol adsorption and decrease the energy barrier of β-C-H bond scission from 1.44 to 0.01 eV due to the strong affinity between the O atom of CuO and the H atom of isopropanol, compared with Au sites alone, thereby achieving ultrahigh acetone selectivity (99.3 %) over 1.1 wt % AuCu_0.75 /Al₂ O₃ at 100 °C and atmospheric pressure with 97.5 % isopropanol conversion. Furthermore, Au-CuO Janus structures supported on SiO₂ , TiO₂ or CeO₂ exhibit remarkable catalytic performance, and great promotion in activity and acetone selectivity is achieved as well for other reducible oxides derived from Fe, Co, Ni and Mn. This study should help to develop strategies for maximized interfacial site construction and structure optimization for efficient β-C-H bond activation.

Cylindrical C96 Fullertubes: A Highly Active Metal-Free O2 -Reduction Electrocatalyst

A new isolation protocol was recently reported for highly purified metallic Fullertubes D_5h -C₉₀ , D_3d -C₉₆ , and D_5d -C_100, which exhibit unique electronic features. Here, we report the oxygen reduction electrocatalytic behavior of C₆₀ , C₇₀ (spheroidal fullerenes), and C₉₀ , C₉₆ , and C₁₀₀ (tubular fullerenes) using a combination of experimental and theoretical approaches. C₉₆ (a metal-free catalyst) displayed remarkable oxygen reduction reaction (ORR) activity, with an onset potential of 0.85 V and a halfway potential of 0.75 V, which are close to the state-of-the-art Pt/C benchmark catalyst values. We achieved an excellent power density of 0.75 W cm^-2 using C₉₆ as a modified cathode in a proton-exchange membrane fuel cell, comparable to other recently reported efficient metal-free catalysts. Combined band structure (experimentally calculated) and free-energy (DFT) investigations show that both favorable energy-level alignment active catalytic sites on the carbon cage are responsible for the superior activity of C₉₆ .

Cation-Tuning Induced d-Band Center Modulation on Co-based Spinel Oxide for Rechargeable Zn-Air Batteries

Atomic substitutions at the tetrahedral site (A Td ) could theoretically achieve an efficient optimization of the charge at the octahedral site (B Oh ) through the A Td -O-B Oh interactions in the spinel oxides (AB2O4). However, the precise control and adjustment of the spinel oxides are still challenging owing to the complexity of their crystal structure. In this work, we demonstrate a simple solvent method to tailor the structures of spinel oxides and further use the spinel oxide composites (ACo2O4/NCNTs, A = Mn, Co, Ni, Cu, Zn) for oxygen electrocatalysis. And the optimized MnCo2O4/NCNTs exhibit high activity and excellent durability for oxygen reduction/evolution reactions. Remarkably, the rechargeable liquid Zn-air battery equipped the MnCo2O4/NCNTs cathode affords a specific capacity of 827 mAh gZn-1 with high power density of 74.63 mW cm-2 and no voltage degradation after 300 cycles at a high charging-discharging rate (5 mA cm-2). The density functional theory (DFT) calculations reveal that the substitution could regulate the ratio of Co3+/Co2+ and thereby lead to the electronic structure modulated accompanied with the movement of d-band center. The tetrahedral and octahedral sites interact through the Mn-O-Co, the Co3+ Oh of MnCo2O4 with the optimal charge structure allows more suitable binding interaction between the active center and the oxygenated species, resulting in superior oxygen electrocatalytic performance. This work not only proves the influence of the charge modulation mechanism on the oxygen catalysis process but also provides novel strategies for the subsequent design of other oxygen catalysis materials.