Detection of nitric oxide release from single cells by using constant-distance-mode scanning electrochemical microscopy

Profiling H2O2 from single COS-7 cells by means of scanning electrochemical microscopy

We report quantitative determination of extracellular H₂O₂ released from single COS-7 cells with high spatial resolution, using scanning electrochemical microscopy (SECM). Our strategy of depth scan imaging in vertical x-z plane was conveniently utilized to a single cell for obtaining probe approach curves (PACs) to any positions on the membrane of a live cell by simply drawing a vertical line on one depth SECM image. This SECM mode provides an efficient way to record a batch of PACs, and visualize cell topography simultaneously. The H₂O₂ concentration at the membrane surface in the center of an intact COS-7 cell was deconvoluted from apparent O₂, and determined to be 0.020 mM by overlapping the experimental PAC with the simulated one having a known H₂O₂ release value. The H₂O₂ profile determined in this way gives insight into physiological activity of single live cells. In addition, intracellular H₂O₂ profile was demonstrated using confocal microscopy by labelling the cells with a luminomphore, 2',7'-dichlorodihydrofluorescein diacetate. The two methodologies have illustrated complementary experimental results of H₂O₂ detection, indicating that H₂O₂ generation is centered at endoplasmic reticula.

An isolated single-particle-based SECM tip interface for single-cell NO sensing

As a key factor in cellular metabolic processes, nitric oxide (NO) is a challenging target for in situ real-time monitoring due to its transient property and short diffusion distance. Scanning electrochemical microscopy (SECM) has unique advantages in single-cell analysis, which can obtain the electrochemical current by scanning the cell surface with a tip microelectrode. In particular, it can further improved the electrochemical response by enhancing the interface properties of its tip. Here, an interface design strategy based on platinum single nanoparticle (Pt NP) was developed, and fluorinated self-assembled monolayers (SAMs) were used to further improve its performance. This modified tip was used as an SECM probe for NO concentration monitoring and morphological imaging of single MCF-7 cells. It has the high sensitivity (164.7 μA/μM·cm²) and good selectivity for NO detection, which benefits from the efficient catalytic properties of Pt NPs and high mass transport and hydrophobic antifouling properties of the interface. Notably, it shows a superior performance in detecting the fluctuation of NO released by a single MCF-7-cell under the stimulation of cadmium (Cd), which demonstrates a promising method for using a single-particle-based tip in SECM applications.

Electrochemical microwell sensor with Fe-N co-doped carbon catalyst to monitor nitric oxide release from endothelial cell spheroids

Endothelial cells have been widely used for vascular biology studies; recent progress in tissue engineering have offered three-dimensional (3D) culture systems for vascular endothelial cells which can be considered as physiologically relevant models. To facilitate the studies, we developed an electrochemical device to detect nitric oxide (NO), a key molecule in the vasculature, for the evaluation of 3D cultured endothelial cells. Using an NO-sensitive catalyst composed of Fe-N co-doped reduced graphene oxide, the real-time monitoring of NO release from the endothelial cell spheroids was demonstrated.

Electrochemical monitoring of reactive oxygen/nitrogen species and redox balance in living cells

Levels of reactive oxygen species (ROS) and reactive nitrogen species (RNS) in cells and cell redox balance are of great interest in live cells as they are correlated to several pathological and physiological conditions of living cells. ROS and RNS detection is limited due to their spatially restricted abundance: they are usually located in sub-cellular areas (e.g., in specific organelles) at low concentration. In this work, we will review and highlight the electrochemical approach to this bio-analytical issue. Combining electrochemical methods and miniaturization strategies, specific, highly sensitive, time, and spatially resolved measurements of cellular oxidative stress and redox balance analysis are possible. Graphical abstract In this work, we highlight and review the use of electrochemistry for the highly spatial and temporal resolved detection of ROS/RNS levels and of redox balance in living cells. These levels are central in several pathological and physiological conditions and the electrochemical approach is a vibrant bio-analytical trend in this field.

Biological imaging with scanning electrochemical microscopy

Scanning electrochemical microscopy (SECM) is a powerful and versatile technique for visualizing the local electrochemical activity of a surface as an ultramicroelectrode tip is moved towards or over a sample of interest using precise positioning systems. In comparison with other scanning probe techniques, SECM not only enables topographical surface mapping but also gathers chemical information with high spatial resolution. Considerable progress has been made in the analysis of biological samples, including living cells and immobilized biomacromolecules such as enzymes, antibodies and DNA fragments. Moreover, combinations of SECM with comple-mentary analytical tools broadened its applicability and facilitated multi-functional analysis with extended life science capabilities. The aim of this review is to present a brief topical overview on recent applications of biological SECM, with particular emphasis on important technical improvements of this surface imaging technique, recommended applications and future trends.

Microsensor systems for cell metabolism - from 2D culture to organ-on-chip

Microsensor systems for cell metabolism are essential tools for investigation and standardization in cell culture. Electrochemical and optical read-out schemes dominate, which enable the marker-free, continuous, online recording of transient effects and deliver information beyond microscopy and end-point tests. There has been much progress in microfluidics and microsensors, but the translation of both into standard cell culture procedures is still limited. Within this critical review, we discuss different cell culture formats ranging from standard culture vessels to dedicated microfluidic platforms. Key aspects are the appropriate supply of cells, mass transport of metabolites to the sensors and generation of stimuli. Microfluidics enable the transition from static to dynamic conditions in culture and measurement. We illustrate the parameters oxygen (respiration), pH (acidification), glucose and lactate (energy metabolism) as well as short-lived reactive species (ROS/RNS) from the perspective of microsensor integration in 2D and 3D cell culture. We discuss different sensor principles and types, along with their limitations, microfabrication technologies and materials. The state-of-the-art of microsensor platforms for cell culture is discussed with respect to sensor performance, the number of parameters and timescale of application. That includes the advances from 2D culture to the increasingly important 3D approaches, with specific requirements for organotypic microtissues, spheroids and solid matrix cultures. We conclude on the current progress, potential, benefits and limitations of cell culture monitoring systems from monolayer culture to organ-on-chip systems.

Fabrication of single Pt@Au nanowire electrodes for monitoring hydrogen peroxide released from living cells

Single Pt@AuNWEs were fabricated by a Cu UPD/Pt redox replacement technique, and were applied to monitoring H₂O₂ released from living cells.

Design and Electrochemical Study of Platinum-Based Nanomaterials for Sensitive Detection of Nitric Oxide in Biomedical Applications

The extensive physiological and regulatory roles of nitric oxide (NO) have spurred the development of NO sensors, which are of critical importance in neuroscience and various medical applications. The development of electrochemical NO sensors is of significant importance, and has garnered a tremendous amount of attention due to their high sensitivity and selectivity, rapid response, low cost, miniaturization, and the possibility of real-time monitoring. Nanostructured platinum (Pt)-based materials have attracted considerable interest regarding their use in the design of electrochemical sensors for the detection of NO, due to their unique properties and the potential for new and innovative applications. This review focuses primarily on advances and insights into the utilization of nanostructured Pt-based electrode materials, such as nanoporous Pt, Pt and PtAu nanoparticles, PtAu nanoparticle/reduced graphene oxide (rGO), and PtW nanoparticle/rGO-ionic liquid (IL) nanocomposites, for the detection of NO. The design, fabrication, characterization, and integration of electrochemical NO sensing performance, selectivity, and durability are addressed. The attractive electrochemical properties of Pt-based nanomaterials have great potential for increasing the competitiveness of these new sensors and open up new opportunities in the creation of novel NO-sensing technologies for biological and medical applications.

Scanning Electrochemical Microscopy (SECM): Fundamentals and Applications in Life Sciences

In recent years, scanning electrochemical microscopy (SECM) has made significant contributions to the life sciences. Innovative developments focusing on high-resolution imaging, developing novel operation modes, and combining SECM with complementary optical or scanning probe techniques renders SECM an attractive analytical approach. This chapter gives an introduction to the essential instrumentation and operation principles of SECM for studying biologically-relevant systems. Particular emphasis is given to applications aimed at imaging the activity of biochemical constituents such as enzymes, antibodies, and DNA, which play a pivotal role in biomedical diagnostics. Furthermore, the unique advantages of SECM and combined techniques for studying live cells is highlighted by discussion of selected examples.

Electrochemical monitoring of intracellular enzyme activity of single living mammalian cells by using a double-mediator system

We evaluated the intracellular

NAD(P)H

quinone oxidoreductase (NQO) activity of single HeLa cells by using the menadione-ferrocyanide double-mediator system combined with scanning electrochemical microscopy (SECM). The double-mediator system was used to amplify the current response from the intracellular NQO activity and to reduce menadione-induced cell damage. The electron shuttle between the electrode and menadione was mediated by the ferrocyanide/ferricyanide redox couple. Generation of ferrocyanide was observed immediately after the addition of a lower concentration (10 μM) of menadione. The ferrocyanide generation rate was constant for 120 min. At a higher menadione concentration (100 μM), the ferrocyanide generation rate decreased within 30 min because of the cytotoxic effect of menadione. We also investigated the relationship between intracellular reactive oxygen species or glutathione levels and exposure to different menadione concentrations to determine the optimal condition for SECM with minimal invasiveness. The present study clearly demonstrates that SECM is useful for the analysis of intracellular enzymatic activities in single cells with a double-mediator system.

Topographical and electrochemical nanoscale imaging of living cells using voltage-switching mode scanning electrochemical microscopy

We describe voltage-switching mode scanning electrochemical microscopy (VSM-SECM), in which a single SECM tip electrode was used to acquire high-quality topographical and electrochemical images of living cells simultaneously. This was achieved by switching the applied voltage so as to change the faradaic current from a hindered diffusion feedback signal (for distance control and topographical imaging) to the electrochemical flux measurement of interest. This imaging method is robust, and a single nanoscale SECM electrode, which is simple to produce, is used for both topography and activity measurements. In order to minimize the delay at voltage switching, we used pyrolytic carbon nanoelectrodes with 6.5-100 nm radii that rapidly reached a steady-state current, typically in less than 20 ms for the largest electrodes and faster for smaller electrodes. In addition, these carbon nanoelectrodes are suitable for convoluted cell topography imaging because the RG value (ratio of overall probe diameter to active electrode diameter) is typically in the range of 1.5-3.0. We first evaluated the resolution of constant-current mode topography imaging using carbon nanoelectrodes. Next, we performed VSM-SECM measurements to visualize membrane proteins on A431 cells and to detect neurotransmitters from a PC12 cells. We also combined VSM-SECM with surface confocal microscopy to allow simultaneous fluorescence and topographical imaging. VSM-SECM opens up new opportunities in nanoscale chemical mapping at interfaces, and should find wide application in the physical and biological sciences.

Towards single-cell analysis for pharmacokinetics

Traditional ‘macroscopic’ pharmacokinetics (PK) investigates the fate of drugs or toxicants administered externally to living organisms, described by the extent and rate of absorption, distribution, metabolism and excretion. However, how a single cell affects a specific pharmaceutical after administration still remains a largely untouched area, primarily due to the technical restrictions imposed by minute amounts of chemicals involved. With the fast development of high-temporal and spatial-resolution detection techniques and single-cell handling techniques, it becomes possible to pursue single-cell PK. This review summarizes useful methodological and experimental techniques to investigate PK at the level of the single cell, including the microfluidics-based single-cell manipulation and the MS and electrochemical methods for single-cell analysis.

Electrochemical nanosensor for real-time direct imaging of nitric oxide in living brain

As gaseous nitric oxide (NO), a critical and multifaceted biomarker, diffuses easily once released, identifying the precise sources of NO release is a challenge. This study developed a new technique for real-time in vivo direct NO imaging by coupling an amperometric NO nanosensor with scanning electrochemical microscopy. This technique provides three-dimensional information of the NO releasing sites in an intact living mouse brain with high sensitivity and spatial resolution. Immunohistochemical analysis was carried out to confirm the anatomical reliability of the acquired electrochemical NO image. The real-time NO imaging results were well matched with the corresponding immunohistochemical analysis of neuronal NO synthase immunoreactive (nNOS-IR) cells, i.e., NO releasing sites in a living brain. The imaged NO local concentrations were confirmed to be closely related to the location in depth, the size of the nNOS-IR cell, and the intensity of nNOS immunoreactivity. This paper demonstrates the first direct electrochemical NO imaging of a living brain.

In situ electrochemical imaging of membrane glycan expression on micropatterned adherent single cells

A scanning electrochemical microscopic (SECM) method for in situ imaging of four types of membrane glycan motifs on single adherent cells was proposed using BGC-823 human gastric carcinoma (BGC) cells as the model. These adherent cells were first micropatterned in the microwell of poly(dimethylsiloxane) membrane for precisely controlling the localized surface interaction, and the membrane glycans were then specifically recognized with corresponding lectins labeled with horseradish peroxidase (HRP). On the basis of the enzymatic oxidization of ferrocenylmethanol (FMA) by H(2)O(2) to yield FMA(+), the glycan expression level was detected by the reduction current of FMA(+) at the SECM tip. The cell-surface glycans could, thus, be in situ imaged by SECM at a single-cell level without peeling the cells from culture dish. Under the optimized conditions, four types of membrane glycan motifs showed statistically distinguishable expression levels. The SECM results for different glycan motifs on adherent single cells were consistent with those estimated by flow cytometric assay. This work provides a reliable approach for in situ evaluation of the characteristic glycopattern of single living cells and can be applied in cell biologic study based on cell surface carbohydrate expression.

Real-time monitoring of cell viability by its nanoscale height change with oxygen as endogenous indicator

A method for real-time evaluation of cell viability was developed by using oxygen as an endogenous indicator in scanning electrochemical microscopy to monitor the nanoscale height change of a single cell in a physiological environment with a novel Pt nanodisk electrode and a newly designed step-approaching strategy.

Redox reactions of reactive oxygen species in aqueous solutions as the probe for scanning electrochemical microscopy of single live T24 cells

The redox reactions of two main components of reactive oxygen species (ROS), superoxide and hydrogen peroxide, along with oxygen in aqueous solutions were investigated using a conventional electrochemical technique, differential pulse voltammetry (DPV). Superoxide undergoes oxidation at a Pt working electrode biased at 0.055 V versus Ag/AgCl, while hydrogen peroxide can be oxidized and reduced at 0.817 and –0.745 V, respectively. Oxygen in the solutions is reduced at the electrode with an applied potential of –0.455 V. Based on these results, hydrogen peroxide and superoxide released from live cells can be successfully monitored, identified, and mapped using scanning electrochemical microscopy (SECM) at different potentials. Single human bladder (T24) cells were imaged using a 5 μm diameter SECM probe biased at –0.400, –0.600, and –0.800 V. Oxygen reduction that seems an interference can be discriminated from that of hydrogen peroxide by means of SECM.

Amperometric nitric oxide microsensor based on nanopore-platinized platinum: the application for imaging NO concentrations

This paper reports an amperometric nitric oxide (NO) microsensor based on a cone-shaped nanopore-platinized Pt working electrode. The senor was fabricated using the following procedure: (1) a parent nanodisk electrode was prepared by polishing an etched Pt wire (radius = 12.5 microm; dimension of etched tip end point <10 nm) embedded in a glass capillary, (2) the nanodisk Pt was further etched to produce a nanopore (pore opening radius <1 microm; pore depth approximately 30 microm), (3) the Pt base surface in the nanopore electrode was platinized electrochemically to improve the sensor sensitivity, and (4) silanization and further modification with the electropolymerized polymeric film [poly(5-amino-1-naphthol)] on the nanopore-platinized Pt electrode were carried out to obtain the sensor selectivity to NO. The analytical performance of the sensor was characterized. For example, a sensor with a pore opening radius of 797 nm exhibited a decent linear dynamic range (at least for 0.2-1.8 microM), detection limit of < approximately 32 nM, response time (t(90%)) of < approximately 5 s, and sensitivity of 6.5 +/- 0.02 pA/nM. This sensor was used successfully as a NO-selective probe tip in scanning electrochemical microscopy (SECM) to obtain a two-dimensional image of the local NO concentrations for an inlaid NO-emitting microdisk film (radius = 12.5 microm) on a glass substrate.

Real-time monitoring of oxidative burst from single plant protoplasts using microelectrochemical sensors modified by platinum nanoparticles

Oxidative bursts from plants play significant roles in plant disease defense and signal transduction; however, it has not hitherto been investigated on individual living plant cells. In this article, we fabricated a novel sensitive electrochemical sensor based on electrochemical deposition of Pt nanoparticles on the surface of carbon fiber microdisk electrodes via a nanopores containing polymer matrix, Nafion. The numerous hydrophilic nanochannels in the Nafion clusters coated on the electrode surface served as the molecular template for the deposition and dispersion of Pt, which resulted in the uniform construction of small Pt nanoparticles. The novel sensor displayed a high sensitivity for detection of H(2)O(2) with a detection limit of 5.0 x 10(-9) M. With the use of this microelectrochemical sensor, the oxidative burst from individual living plant protoplasts have been real-time monitored for the first time. The results showed that oxidative burst from single protoplasts triggered by a pathogen analogue were characterized by quanta release with a large number of "transient oxidative microburst" events, and protoplasts from the transgenic plants biologically displayed better disease-resistance and showed a distinguished elevation and longer-lasting oxidative burst.

Scanning electrochemical microscopy in neuroscience

This article reviews recent work involving the application of scanning electrochemical microscopy (SECM) to the study of individual cultured living cells, with an emphasis on topographical and functional imaging of neuronal and secretory cells of the nervous and endocrine system. The basic principles of biological SECM and associated negative amperometric-feedback and generator/collector-mode SECM imaging are discussed, and successful use of the methodology for screening soft and fragile membranous objects is outlined. The drawbacks of the constant-height mode of probe movement and the benefits of the constant-distance mode of SECM operation are described. Finally, representative examples of constant-height and constant-distance mode SECM on a variety of live cells are highlighted to demonstrate the current status of single-cell SECM in general and of SECM in neuroscience in particular.

Odorant-dependent generation of nitric oxide in Mammalian olfactory sensory neurons

The gaseous signalling molecule nitric oxide (NO) is involved in various physiological processes including regulation of blood pressure, immunocytotoxicity and neurotransmission. In the mammalian olfactory bulb (OB), NO plays a role in the formation of olfactory memory evoked by pheromones as well as conventional odorants. While NO generated by the neuronal isoform of NO synthase (nNOS) regulates neurogenesis in the olfactory epithelium, NO has not been implicated in olfactory signal transduction. We now show the expression and function of the endothelial isoform of NO synthase (eNOS) in mature olfactory sensory neurons (OSNs) of adult mice. Using NO-sensitive micro electrodes, we show that stimulation liberates NO from isolated wild-type OSNs, but not from OSNs of eNOS deficient mice. Integrated electrophysiological recordings (electro-olfactograms or EOGs) from the olfactory epithelium of these mice show that NO plays a significant role in modulating adaptation. Evidence for the presence of eNOS in mature mammalian OSNs and its involvement in odorant adaptation implicates NO as an important new element involved in olfactory signal transduction. As a diffusible messenger, NO could also have additional functions related to cross adaptation, regeneration, and maintenance of MOE homeostasis.