Nitrogen-Doped Cobalt Diselenide with Cubic Phase Maintained for Enhanced Alkaline Hydrogen Evolution

Semimetal-triggered covalent interaction in Pt-based intermetallics for fuel-cell electrocatalysis

Platinum-based intermetallic compounds (IMCs) play a vital role as electrocatalysts in a range of energy and environmental technologies, such as proton exchange membrane fuel cells. However, the synthesis of IMCs necessitates recombination of ordered Pt-M metallic bonds with high temperature driving, which is generally accompanied by side effects for catalysts' structure and performance. In this work, we highlight that semimetal atoms can trigger covalent interactions to break the synthesis-temperature limitation of platinum-based intermetallic compounds and benefit fuel-cell electrocatalysis. Attributed to partial fillings of p-block in semimetal elements, the strong covalent interaction of d-p π backbonding can benefit the recombination of ordered Pt-M metallic bonds (PtGe, PtSb and PtTe) in the synthesis process. Moreover, this covalent interaction in metallic states can further promote both electron transport and orbital fillings of active sites in fuel cells. The semimetal-Pt IMCs were obtained with a temperature 300 K lower than that needed for the synthesis of metal-Pt intermetallic compounds and reached the highest CO-tolerant oxygen reduction activity (0.794 A mg-1 at 0.9 V and 5.1% decay under CO poisoning) among reported electrocatalysts. We anticipate that semimetal-Pt IMCs will offer new insights for the rational design of advanced electrocatalysts for fuel cells.

Oxygenate-induced structural evolution of high-entropy electrocatalysts for multifunctional alcohol electrooxidation integrated with hydrogen production

High-entropy compounds have been emerging as promising candidates for electrolysis, yet their controllable electrosynthesis strategy remains a formidable challenge because of the ambiguous ionic interaction and codeposition mechanism. Herein, we report a oxygenates directionally induced electrodeposition strategy to construct high-entropy materials with amorphous features, on which the structural evolution from high-entropy phosphide to oxide is confirmed by introducing vanadate, thus realizing the simultaneous optimization of composition and structure. The representative P-CoNiMnWVOx shows excellent bifunctional catalytic performance toward alkaline hydrogen evolution reaction and ethanol oxidation reaction (EOR), with small potentials of -168 mV and 1.38 V at 100 mA cm-2, respectively. In situ spectroscopy illustrates that the electrochemical reconstruction of P-CoNiMnWVOx induces abundant Co-O species as the main catalytic active species for EOR and follows the conversion pathway of the C2 product. Theoretical calculations reveal the optimized electronic structure and adsorption free energy of reaction intermediates on P-CoNiMnWVOx, thereby resulting in a facilitated kinetic process. A membrane-free electrolyzer delivers both high Faradaic efficiencies of acetate and H2 over 95% and superior stability at100 mA cm-2 during 120 h electrolysis. In addition, the unique composition and structural advantages endow P-CoNiMnWVOx with multifunctional catalytic activity and realize multipathway electrosynthesis of formate-coupled hydrogen production.

Construction of Co-Se-W at Interfaces of Phase-Mixed Cobalt Selenide via Spontaneous Phase Transition for Platinum-Like Hydrogen Evolution Activity and Long-Term Durability in Alkaline and Acidic Media

Cost-effective transition metal chalcogenides are highly promising electrocatalysts for both alkaline and acidic hydrogen evolution reactions (HER). However, unsatisfactory HER kinetics and stability have severely hindered their applications in industrial water electrolysis. Herein, a nanoflowers-shaped W-doped cubic/orthorhombic phase-mixed CoSe2 catalyst ((c/o)-CoSe2-W) is reported. The W doping induces spontaneous phase transition from stable phase cubic CoSe2 (c-CoSe2) to metastable phase orthorhombic CoSe2, which not only enables precise regulation of the ratio of two phases but also realizes W doping at the interfaces of two phases. The (c/o)-CoSe2-W catalyst exhibits a Pt-like HER activity in both alkaline and acidic media, with record-low HER overpotentials of 29.8 mV (alkaline) and 35.9 mV (acidic) at 10 mA cm-2, respectively, surpassing the vast majority of previously reported non-precious metal electrocatalysts for both alkaline and acidic HER. The Pt-like HER activities originate from the formation of Co-Se-W active species on the c-CoSe2 side at the phase interface, which effectively modulates electron structures of active sites, not only enhancing H2O adsorption and dissociation at Co sites but also optimizing H* adsorption to ΔGH* ≈ 0 at W sites. Benefiting from the abundant phase interfaces, the catalyst also displays outstanding long-term durability in both acidic and alkaline media.

Lattice Strain with Stabilized Oxygen Vacancies Boosts Ceria for Robust Alkaline Hydrogen Evolution Outperforming Benchmark Pt

Earth-abundant metal oxides are usually considered as stable but catalytically inert toward hydrogen evolution reaction (HER) due to their unfavorable hydrogen intermediate adsorption performance. Herein, a heavy rare earth (Y) and transition metal (Co) dual-doping induced lattice strain and oxygen vacancy stabilization strategy is proposed to boost CeO2 toward robust alkaline HER. The induced lattice compression and increased oxygen vacancy (Ov) concentration in CeO2 synergistically improve the water dissociation on Ov sites and sequential hydrogen adsorption at activated Ov-neighboring sites, leading to significantly enhanced HER kinetics. Meanwhile, Y doping offers stabilization effect on Ov by its stronger Y─O bonding over Ce─O, which endows the catalyst with excellent stability. The Y,Co-CeO2 electrocatalyst exhibits an ultra-low HER overpotential (27 mV at 10 mA cm-2) and Tafel slope (48 mV dec-1), outperforming the benchmark Pt electrocatalyst. Moreover, the anion exchange membrane water electrolyzer incorporated with Y,Co-CeO2 achieves excellent stability of 500 h under 600 mA cm-2. This synergistic lattice strain and oxygen vacancy stabilization strategy sheds new light on the rational development of efficient and stable oxide-based HER electrocatalysts.

Augmented Electrochemical Oxygen Evolution by d-p Orbital Electron Coupling

While high-entropy alloys, high-entropy oxides, and high-entropy hydroxides, are advanced as a novel frontier in electrocatalytic oxygen evolution, their inherent activity deficiency poses a major challenge. To achieve the unlimited goal to tailor the structure-activity relationship in multicomponent systems, entropy-driven composition engineering presents substantial potential, by fabricating high-entropy anion-regulated transition metal compounds as sophisticated oxygen evolution reaction electrocatalysts. Herein, a versatile 2D high-entropy metal phosphorus trisulfide is developed as a promising and adjustable platform. Leveraging the multiple electron couplings and d-p orbital hybridizations induced by the cocktail effect, the exceptional oxygen evolution catalytic activity is disclosed upon van der Waals material (MnFeCoNiZn)PS3, exhibiting an impressively low overpotential of 240 mV at a current density of 10 mA cm-2, a minimal Tafel slope of 32 mV dec-1, and negligible degradation under varying current densities for over 96 h. Density functional theory calculations further offer insights into the correlation between orbital hybridization and catalytic performance within high-entropy systems, underscoring the contribution of active phosphorus centers on the substrate to performance enhancements. Moreover, by achieving electron redistribution to optimize the electron coordination environment, this work presents an effective strategy for advanced catalysts in energy-related applications.

In Situ Construction of Built-In Opposite Electric Field Balanced Surface Adsorption for Hydrogen Evolution Reaction

Achieving a balance between H-atom adsorption and binding with H2 desorption is crucial for catalyzing hydrogen evolution reaction (HER). In this study, the feasibility of designing and implementing built-in opposite electric fields (OEF) is demonstrated to enable optimal H atom adsorption and H2 desorption using the Ni3(BO3)2/Ni5P4 heterostructure as an example. Through density functional theory calculations of planar averaged potentials, it shows that opposite combinations of inward and outward electric fields can be achieved at the interface of Ni3(BO3)2/Ni5P4, leading to the optimization of the H adsorption free energy (ΔGH*) near electric neutrality (0.05 eV). Based on this OEF concept, the study experimentally validated the Ni3(BO3)2/Ni5P4 system electrochemically forming Ni3(BO3)2 through cyclic voltammetry scanning of B-doped Ni5P4. The surface of Ni3(BO3)2 undergoes reconstruction, as characterized by Grazing Incidence Wide-Angle X-ray Scattering (GIWAXS) and in situ Raman spectroscopy. The resulting catalyst exhibits excellent HER activity in alkaline media, with a low overpotential of 33 mV at 10 mA cm-2 and stability maintained for over 360 h. Therefore, the design strategy of build-in opposite electric field enables the development of high-performance HER catalysts and presents a promising approach for electrocatalyst advancement.

Sublayer-Sulfur-Vacancy-Induced Charge Redistribution of FeCuS Nanoflower Awakening Alkaline Hydrogen Evolution

Advancing the progress of sustainable and green energy technologies requires the improvement of valid electrocatalysts for the hydrogen evolution reaction (HER). Reconfiguring charge distribution through heteroatom doping-induced vacancy serves as an effective approach to implement high performance for HER catalysts. Here, we successfully fabricated Fe-doped CuS (FeCuS) with the sublayer sulfur vacancy to judge its HER performance and dissect the activity origins. Density functional theory calculation further elucidates that the primary factor contributing to the heightened HER activity is that the sublayer sulfur vacancies awaken the charge redistribution. In addition to effectively decreasing the energy barrier associated with the Volmer step, it modulates the adsorption/desorption capacity of H*. As a result, its intrinsic activity for the HER has significantly increased. Concretely, the obtained FeCuS displays an excellent catalytic performance, whose Tafel slope is only 59 mV dec-1 and the overpotential (at 10 mA cm-2) is as low as 71 mV in an alkaline environment, surpassing the majority of previously documented catalysts in scientific literature. This work shows that the construction of sublayer sulfur vacancies by Fe doping can achieve the charge redistribution and precise tuning of electronic structure; thereby, the inert CuS can be transformed into highly efficient electrocatalysts.

Crystal Structure Regulation of CoSe2 Induced by Fe Dopant for Promoted Surface Reconstitution toward Energetic Oxygen Evolution Reaction

Most nonoxide catalysts based on transition metal elements will inevitably change their primitive phases under anodic oxidation conditions in alkaline media. Establishing a relationship between the bulk phase and surface evolution is imperative to reveal the intrinsic catalytic active sites. In this work, it is demonstrated that the introduction of Fe facilitates the phase transition of orthorhombic CoSe2 into its cubic counterpart and then accelerates the Co-Fe hydroxide layer generation on the surface during electrocatalytic oxygen evolution reaction (OER). As a result, the Fe-doped cubic CoSe2 catalyst exhibits a significantly enhanced activity with a considerable overpotential decrease of 79.9 and 66.9 mV to deliver 10 mA·cm-2 accompanied by a Tafel slope of 48.0 mV·dec-1 toward OER when compared to orthorhombic CoSe2 and Fe-doped orthorhombic CoSe2, respectively. Density functional theory (DFT) calculations reveal that the introduction of Fe on the surface hydroxide layers will tune electron density around Co atoms and raise the d-band center. These findings will provide deep insights into the surface reconstitution of the OER electrocatalysts based on transition metal elements.

Bifunctional Electrocatalysts for Overall and Hybrid Water Splitting

Electrocatalytic water splitting driven by renewable electricity has been recognized as a promising approach for green hydrogen production. Different from conventional strategies in developing electrocatalysts for the two half-reactions of water splitting (e.g., the hydrogen and oxygen evolution reactions, HER and OER) separately, there has been a growing interest in designing and developing bifunctional electrocatalysts, which are able to catalyze both the HER and OER. In addition, considering the high overpotentials required for OER while limited value of the produced oxygen, there is another rapidly growing interest in exploring alternative oxidation reactions to replace OER for hybrid water splitting toward energy-efficient hydrogen generation. This Review begins with an introduction on the fundamental aspects of water splitting, followed by a thorough discussion on various physicochemical characterization techniques that are frequently employed in probing the active sites, with an emphasis on the reconstruction of bifunctional electrocatalysts during redox electrolysis. The design, synthesis, and performance of diverse bifunctional electrocatalysts based on noble metals, nonprecious metals, and metal-free nanocarbons, for overall water splitting in acidic and alkaline electrolytes, are thoroughly summarized and compared. Next, their application toward hybrid water splitting is also presented, wherein the alternative anodic reactions include sacrificing agents oxidation, pollutants oxidative degradation, and organics oxidative upgrading. Finally, a concise statement on the current challenges and future opportunities of bifunctional electrocatalysts for both overall and hybrid water splitting is presented in the hope of guiding future endeavors in the quest for energy-efficient and sustainable green hydrogen production.

Nano-Cu Derived from a Copper Nitride Precatalyst for Reductive Coupling of Nitroaromatics to Azo Compounds

The study of structural reconstruction is vital for the understanding of the real active sites in heterogeneous catalysis and guiding the improved catalyst design. Herein, we applied a copper nitride precatalyst in the nitroarene reductive coupling reaction and made a systematic investigation on the dynamic structural evolution behaviors and catalytic performance. This Cu3N precatalyst undergoes a rapid phase transition to nanostructured Cu with rich defective sites, which act as the actual catalytic sites for the coupling process. The nitride-derived defective Cu is very active and selective for azo formation, with 99.6% conversion of nitrobenzene and 97.1% selectivity to azobenzene obtained under mild reaction conditions. Density functional theory calculations suggest that the defective Cu sites play a role for the preferential adsorption of nitrosobenzene intermediates and significantly lowered the activation energy of the key coupling step. This work not only proposes a highly efficient noble-metal-free catalyst for nitroarenes coupling to valuable azo products but also may inspire more scientific interest in the study of the dynamic evolution of metal nitrides in different catalytic reactions.

Surface engineering for stable electrocatalysis

In recent decades, significant progress has been achieved in rational developments of electrocatalysts through constructing novel atomistic structures and modulating catalytic surface topography, realizing substantial enhancement in electrocatalytic activities. Numerous advanced catalysts were developed for electrochemical energy conversion, exhibiting low overpotential, high intrinsic activity, and selectivity. Yet, maintaining the high catalytic performance under working conditions with high polarization and vigorous microkinetics that induce intensive degradation of surface nanostructures presents a significant challenge for commercial applications. Recently, advanced operando and computational techniques have provided comprehensive mechanistic insights into the degradation of surficial functional structures. Additionally, various innovative strategies have been devised and proven effective in sustaining electrocatalytic activity under harsh operating conditions. This review aims to discuss the most recent understanding of the degradation microkinetics of catalysts across an entire range of anodic to cathodic polarizations, encompassing processes such as oxygen evolution and reduction, hydrogen reduction, and carbon dioxide reduction. Subsequently, innovative strategies adopted to stabilize the materials' structure and activity are highlighted with an in-depth discussion of the underlying rationale. Finally, we present conclusions and perspectives regarding future research and development. By identifying the research gaps, this review aims to inspire further exploration of surface degradation mechanisms and rational design of durable electrocatalysts, ultimately contributing to the large-scale utilization of electroconversion technologies.

From Synthesis to Mechanisms: In-Depth Exploration of the Dual-Atom Catalytic Mechanisms Toward Oxygen Electrocatalysis

Dual-atom catalysts (DACs) hold a higher metal atom loading and provide greater flexibility in terms of the structural characteristics of their active sites in comparison to single-atom catalysts. Consequently, DACs hold great promise for achieving improved catalytic performance. This article aims to provide a focused overview of the latest advancements in DACs, covering their synthesis and mechanisms in reversible oxygen electrocatalysis, which plays a key role in sustainable energy conversion and storage technologies. The discussion starts by highlighting the structures of DACs and the differences in diatomic coordination induced by various substrates. Subsequently, the state-of-the-art fabrication strategies of DACs for oxygen electrocatalysis are discussed from several different perspectives. It particularly highlights the challenges of increasing the diatomic loading capacity. More importantly, the main focus of this overview is to investigate the correlation between the configuration and activity in DACs in order to gain a deeper understanding of their active roles in oxygen electrocatalysis. This will be achieved through density functional theory calculations and sophisticated in situ characterization technologies. The aim is to provide guidelines for optimizing and upgrading DACs in oxygen electrocatalysis. Additionally, the overview discusses the current challenges and future prospects in this rapidly evolving area of research.

Modulation of Phase Transition in Cobalt Selenide with Simultaneous Construction of Heterojunctions for Highly-Efficient Oxygen Electrocatalysis in Zinc-Air Battery

Phase transformation of cobalt selenide (CoSe2 ) can effectively modulate its intrinsic electrocatalytic activity. However, enhancing electroconductivity and catalytic activity/stability of CoSe2 still remains challenging. Heterostructure engineering may be feasible to optimize interfacial properties to promote the kinetics of oxygen electrocatalysis on a CoSe2 -based catalyst. Herein, a heterostructure consisting of CoSe2 and cobalt nitride (CoN) embedded in a hollow carbon cage is designed via a simultaneous phase/interface engineering strategy. Notably, the phase transition of orthorhombic-CoSe2 to cubic-CoSe2 (c-CoSe2 ) accompanied by in situ CoN formation is realized to build the c-CoSe2 /CoN heterointerface, which exhibits excellent/highly stable activities for oxygen reduction/evolution reactions (ORR/OER). Notably, heterostructure can modulate the local coordination environment and increase Co-Se/N bond lengths. Theoretical calculations show that Co-site (c-CoSe2 ) with an electronic state near Fermi energy level is the main active site for ORR/OER.Energetical tailoring of the d-orbital electronic structure of the Co atom of c-CoSe2 in heterostructure by in situ CoN incorporation lowers thermodynamic barriers for ORR/OER. Attractively, a zinc-air battery with a c-CoSe2 -CoN cathode displays excellent cycling stability (250 h) and charge/discharge voltage loss (0.953/0.96 V). It highlights that heterointerface engineering provides an option for modulating the bifunctional activity of metal selenides with controlled phase transformation.

A Strongly Coupled Ag(S)@NiO/Nickel Foam Electrode Induced by Laser Direct Writing for Hydrogen Evolution at Ultrahigh Current Densities with Long-Term Durability

Highly active, durable, and cost-effective electrodes for hydrogen evolution reaction (HER) at ultrahigh current densities (≥1 A cm-2 ) are extremely demanded for industrial high-rate hydrogen production, but challenging. Here, a robust strongly coupled Ag(S)@NiO/nickel foam (NF) electrode is reported. Taking advantage of millisecond laser direct writing in liquid nitrogen technique, lattice-matched and coherent interfaces are formed between Ag nanoparticles with stacking faults (denoted by Ag(S)) and NiO nanosheets, leading to strong interfacial electronic coupling, not only promoting H2 O adsorption and dissociation on Ni2+ but also enhancing H* adsorption on intrinsically inactive but most electrically conductive Ag. Strong chemical bonding is established at NiO/NF interface, guaranteeing rapid electron transfer and excellent mechanical durability under high-rate hydrogen evolution. The physicochemically stable electrode achieves record-low alkaline HER overpotential of 167 and 180 mV at 1 and 1.5 A cm-2 , respectively, along with negligible activity decay after 120 h test at ≈1.5 A cm-2 , surpassing reported non-platinum group metal electrocatalysts.

Fabricating Ru Atom-Doped Novel FeP4/Fe2PO5 Heterogeneous Interface for Overall Water Splitting in Alkaline Environment

Developing bifunctional electrocatalysts with low-content noble metals and high activity and stability is crucial for water splitting. Herein, we reported a novel Ru doped FeP4/Fe2PO5 heterogeneous interface catalyst (Ru@FeP4/Fe2PO5) for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) by heat treatment coupling electrodeposition strategy. Experiments disclosed that Ru@FeP4/Fe2PO5 proclaimed excellent catalytic activity for the OER (249 mV@100 mA cm-2) and HER (49 mV@10 mA cm-2) in a 1 M KOH environment. More importantly, the mass activity and turnover frequency of Ru@FeP4/Fe2PO5 were 117 and 108 times higher than that of commercial RuO2 at an overpotential of 300 mV during the OER, respectively. In addition, the assembled Ru@FeP4/Fe2PO5 || Ru@FeP4/Fe2PO5 system could retain superior durability in a two-electrode system for 134 h at 300 mA cm-2. Further mechanism studies revealed that Ru atoms in Ru@FeP4/Fe2PO5 act in a key role for the excellent activity during water splitting because the electronic structure of Ru sites could be optimized by the interaction between Ru and Fe atoms at the interface to strengthen the adsorption of reaction intermediates. Besides, the introduction of Ru atoms could also enhance the charge transfer, which effectually accelerates the reaction kinetics. The strategy of anchoring Ru atom on novel heterostructure provides a promising path to boost the overall activity of electrocatalysts for water splitting.

Atomically precise AuxAg25-x nanoclusters with a modulated interstitial Au-Ag microenvironment for enhanced visible-light-driven photocatalytic hydrogen evolution

Herein, we report the study of atomically precise AuxAg25-x nanoclusters (NCs) toward photocatalytic hydrogen evolution. The incorporation of Au atoms into Ag25 NCs not only narrowed the HOMO-LUMO gaps but also created an interstitial Au-Ag microenvironment, which promoted the photogenerated charge carrier utilization and optimized the reaction dynamics.

Electronic Modulation Induced by Ni-VN Heterojunction Reinforces Electrolytic Hydrogen Evolution Coupled with Biomass Upgrade

The renewable electricity-driven hydrogen evolution reaction (HER) coupled with biomass oxidation is a powerful avenue to maximize the energy efficiency and economic feedback, but challenging. Herein, porous Ni-VN heterojunction nanosheets on nickel foam (Ni-VN/NF) are constructed as a robust electrocatalyst to simultaneously catalyze HER and 5-hydroxymethylfurfural electrooxidation reaction (HMF EOR). Benefiting from the surface reconstruction of Ni-VN heterojunction during the oxidation process, the derived NiOOH-VN/NF energetically catalyzes HMF into 2,5-furandicarboxylic acid (FDCA), yielding the high HMF conversion (>99%), FDCA yield (99%), and Faradaic efficiency (>98%) at the lower oxidation potential along with the superior cycling stability. Ni-VN/NF is also surperactive for HER, exhibiting an onset potential of ≈0 mV and Tafel slope of 45 mV dec-1 . The integrated Ni-VN/NF||Ni-VN/NF configuration delivers a compelling cell voltage of 1.426 V at 10 mA cm-2 for the H2 O-HMF paired electrolysis, about 100 mV lower than that for water splitting. Theoretically, for Ni-VN/NF, the superiority in HMF EOR and HER is mainly dominated by the local electronic distribution at the heterogenous interface, which accelerates the charge transfer and optimize the adsorption of reactants/intermediates by modulating the d-band center, therefore being an advisable thermodynamic and kinetic process.

2D Cobalt Chalcogenide Heteronanostructures Enable Efficient Alkaline Hydrogen Evolution Reaction

The development of high-efficiency non-precious metal electrocatalysts for alkaline electrolyte hydrogen evolution reactions (HER) is of great significance in energy conversion to overcome the limited supply of fossil fuels and carbon emission. Here, a highly active electrocatalyst is presented for hydrogen production, consisting of 2D CoSe2 /Co3 S4 heterostructured nanosheets along Co3 O4 nanofibers. The different reaction rate between the ion exchange reaction and redox reaction leads to the heterogeneous volume swelling, promoting the growth of 2D structure. The 2D/1D heteronanostructures enable the improved the electrochemical active area, the number of active sites, and more favorable H binding energy compared to individual cobalt chalcogenides. The roles of the different composition of the heterojunction are investigated, and the electrocatalysts based on the CoSe2 /Co3 S4 @Co3 O4 exhibited an overpotential as low as 165 mV for 10 mA cm-2 and 393 mV for 200 mA cm-2 in 1 m KOH electrolyte. The as-prepared electrocatalysts remained active after 55 h operation without any significant decrease, indicating the excellent long-term operation stability of the electrode. The Faradaic efficiency of hydrogen production is close to 100% at different voltages. This work provides a new design strategy toward Co-based catalysts for efficient alkaline HER.

Selenite-Decorated Polycrystalline NiO Nanosheets Generated from Cathodic Reconstruction for Electrocatalytic Hydrogen Production

Precatalyst reconstruction in alkaline hydrogen evolution reaction (HER) usually leads to changes in the morphology, composition, and structure, thus improving the catalytic activity, which recently receives intensive attention. However, the design strategies of cathodic reconstruction and the structural features of reconstruction products have not achieved a profound understanding. Here, from the point of thermodynamic stability, metastable nickel selenite dihydrate (NiSeO₃·2H₂O) is deliberately fabricated as a precatalyst to comprehensively study the reconstruction dynamics in alkaline HER. Multiple in/ex situ techniques capture the geometric, component, and phase evolutions, proving that NiSeO₃·2H₂O can be transformed into SeO₃^2--decorated polycrystalline NiO nanosheets with rich active sites and good conductivity under alkaline HER conditions, which act as a real catalytic active species. Density functional theory calculations demonstrate that the adsorption of SeO₃^2- can further promote the HER activity of NiO due to the optimized free energy of water activation and hydrogen adsorption. As a result, the SeO₃^2--NiO catalyst exhibits a low overpotential at -10 mA cm^-2 (90 mV) and long-term stability (>100 h). This work highlights the targeted design of precatalyst to trigger and utilize cathodic reconstruction and provides an available method for the development of adsorption-modulated efficient electrocatalysts.

Tuning Electron Transfer in Atomic-Scale Pt-Supported Catalysts for the Alkaline Hydrogen Oxidation Reaction

Developing efficient atomic-scale metal-supported catalysts is of great significance for energy conversion technologies. However, the precise modulation of electron transfer between the metal and supporter in atomic-scale metal-supported catalysts to further improve the catalytic activity is still a major challenge. Herein, we show tunable electron transfer between atomic-scale Pt and tungsten nitride/oxide supports (namely, Pt/WN and Pt/W₁₈O₄₉). Pt/WN with modest electron exchange and Pt/W₁₈O₄₉ with aggressive electron exchange exhibit notably different catalytic activities for the alkaline hydrogen oxidation reaction (HOR), in which Pt/WN shows a 5.7-fold enhancement in HOR intrinsic catalytic performance in comparison to Pt/W₁₈O₄₉. Additionally, the tunable electronic transfer at the interface of Pt/WN and Pt/W₁₈O₄₉, as proven by the theoretical calculation, resulted in the discrepancy of the adsorption free energy of the reaction intermediates, as well as catalytic activity, for the HOR process. Our work provides new insights into the design of advanced atomic-scale metal-supported catalysts for electrocatalysis.

Charge Redistribution of Co9S8/MoS2 Heterojunction Microsphere Enhances Electrocatalytic Hydrogen Evolution

The electrocatalytic hydrogen evolution activity of transition metal sulfide heterojunctions are significantly increased when compared with that of a single component, but the mechanism behind the performance enhancement and the preparation of catalysts with specific morphologies still need to be explored. Here, we prepared a Co9S8/MoS2 heterojunction with microsphere morphology consisting of thin nanosheets using a facile two-step method. There is electron transfer between the Co9S8 and MoS2 of the heterojunction, thus realizing the redistribution of charge. After the formation of the heterojunction, the density of states near the Fermi surface increases, the d-band center of the transition metal moves downward, and the adsorption of both water molecules and hydrogen by the catalyst are optimized. As a result, the overpotential of Co9S8/MoS2 is superior to that of most relevant electrocatalysts reported in the literature. This work provides insight into the synergistic mechanisms of heterojunctions and their morphological regulation.

Molybdenum Oxycarbide Supported Rh-Clusters with Modulated Interstitial C-O Microenvironments for Promoting Hydrogen Evolution

Tuning the microenvironment and electronic structure of support materials is essential strategy to induce electron transfer between supports and active centers, which is of great importance in optimizing catalytic kinetics. In this study, the molybdenum oxycarbide supported Rh-clusters are synthesized with modulated interstitial C-O microenvironments (Rh/MoOC) for promoting efficient hydrogen evolution in water splitting. Both electronic structure characterizations and theoretical calculations uncover the apparent charge transfer from Rh to MoOC, which optimizes the d-band center, H₂ O adsorption energy, and hydrogen binding energy, thus enhancing its intrinsic hydrogen-evolving activities. In addition, the co-occurrence of interstitial C and O atoms in MoOC supports plays a vital role in the dissociation reaction of water during the hydrogen-evolving process. Impressively, the Rh/MoOC exhibits excellent hydrogen-evolving activities in terms of exceptional turnover frequency values (11.4 and 39.41 H₂ s^-1 in alkaline and acidic media) and mass activities (21.3 and 73.87 A mg^-1 in alkaline and acidic media) at an overpotential of 100 mV, which is more than 40 times higher than that of the benchmark commercial Rh/C catalysts. This work sheds new light on designing water dissociation materials that surpasses most of the reported catalysts.

Tuning the Local Coordination of CoP1-xSx between NiAs- and MnP-Type Structures to Catalyze Lithium-Sulfur Batteries

The slow conversion and rapid shuttling of polysulfides remain major challenges that hinder the practical application of lithium-sulfur (Li-S) batteries. Efficient catalysts are needed to accelerate the conversion and suppress the shuttling. However, the lack of a rational understanding of catalysis poses obstacles to the design of catalysts, thereby limiting the rapid development of Li-S batteries. Herein, we theoretically analyze the modulation of the electronic structure of CoP_1-xS_x caused by the NiAs-to-MnP-type transition and its influence on catalytic activity. We found that the interacting d-orbitals of the active metal sites play a determining role in adsorption and catalysis, and the optimal d_z²-, d_xz-, and d_yz-orbitals in an appropriately distorted five-coordinate pyramid enable higher catalytic activity compared with their parent structures. Finally, rationally designed catalysts and S were electrospun into carbonized nanofibers to form nanoreactor chains for use as cathodes. The resultant Li-S batteries exhibited superior properties over 1000 cycles with only a decay rate of 0.031% per cycle and demonstrated a high capacity of 887.4 mAh g^-1 at a high S loading of 10 mg cm^-2. The structural modulation and bonding analyses in this study provide a powerful approach for the rational design of Li-S catalysts.

Construction of Cobalt Molybdenum Diselenide Three-phase Heterojunctions for Electrocatalytic Hydrogen Evolution in Acid Medium

Molybdenum diselenide and cobalt diselenide have been commonly implemented in electrocatalytic hydrogen evolution reaction (HER). However, there have been few research on the creation of their three-phase heterojunctions and the associated HER process. Herein, we constructed a three-phase heterostructure sample consisting of orthorhombic CoSe₂ , cubic CoSe₂ and MoSe₂ and we investigated its HER performance. The sample shows microsphere morphology composed of nanosheets with interfacial interactions between the components. It possesses an overpotential of -136 mV at -10 mA cm^-2 in acid medium, which is superior to that of single component and most two-phase heterostructures. Especially, the overpotential at -200 mA cm^-2 is smaller than that of Pt/C. The excellent performance can be attributed to the d-orbital upshift of the Co active sites due to charge redistribution between the three-phase heterojunction and the optimization of the hydrogen free energy. This work provides inspiration for exploring the application of other multi-component heterojunctions in electrocatalytic hydrogen evolution.

Two Birds with One Stone: Concurrent Ligand Removal and Carbon Encapsulation Decipher Thickness-Dependent Catalytic Activity

A carbon shell encapsulating a transition metal-based core has emerged as an intriguing type of catalyst structure, but the effect of the shell thickness on the catalytic properties of the buried components is not well known. Here, we present a proof-of-concept study to reveal the thickness effect by carbonizing the isotropic and homogeneous oleylamine (OAm) ligands that cover colloidal MoS₂. A thermal treatment turns OAm into a uniform carbon shell, while the size of MoS₂ monolayers remains identical. When evaluated toward an acidic hydrogen evolution reaction, the calcined MoS₂ catalysts deliver a volcano-type activity trend that depends on the calcination temperature. Rutherford backscattering spectrometry and depth-profiling X-ray photoelectron spectroscopy consistently provide an accurate quantification of the carbon shell thickness. The same variation pattern of catalytic activity and carbon shell thickness, aided by kinetic studies, is then persuasively justified by the respective limitations of electron and proton conductivities on the two branches of the volcano curve.

Accelerated water activation and stabilized metal-organic framework via constructing triangular active-regions for ampere-level current density hydrogen production

Two-dimensional metal-organic frameworks (MOFs) have been explored as effective electrocatalysts for hydrogen evolution reaction (HER). However, the sluggish water activation kinetics and structural instability under ultrahigh-current density hinder their large-scale industrial applications. Herein, we develop a universal ligand regulation strategy to build well-aligned Ni-benzenedicarboxylic acid (BDC)-based MOF nanosheet arrays with S introducing (S-NiBDC). Benefiting from the closer p-band center to the Fermi level with strong electron transferability, S-NiBDC array exhibits a low overpotential of 310 mV to attain 1.0 A cm^-2 with high stability in alkaline electrolyte. We speculate the newly-constructed triangular "Ni₂-S₁" motif as the improved HER active region based on detailed mechanism analysis and structural characterization, and the enhanced covalency of Ni-O bonds by S introducing stabilizes S-NiBDC structure. Experimental observations and theoretical calculations elucidate that such Ni sites in "Ni₂-S₁" center distinctly accelerate the water activation kinetics, while the S site readily captures the H atom as the optimal HER active site, boosting the whole HER activity.

Interlayer Spacing Regulation of Molybdenum Selenide Promotes Electrocatalytic Hydrogen Evolution in Alkaline Media

The construction of heterostructures is a versatile tactic to enhance catalytic activity. However, it is still elusive to realize the modulation of the interlayer spacing in this way to further improve the performance. Here, strong interfacial coupling between CoSe₂ and MoSe₂ by constructing CoSe₂ /MoSe₂ heterostructures is achieved. The interlayer spacing of MoSe₂ is compressed by 0.3 Å. The enhanced charge transfer is validated by X-ray absorption spectroscopy and X-ray photoelectron spectroscopy. Coupled with the morphology of hollow microtubes, which can facilitate the exposure of active sites, CoSe₂ /MoSe₂ heterostructures reported here exhibit high activity (119 mV at 10 mA cm^-2 ) and excellent stability with small degradation after 50 h operation, surpassing other analogous powdered electrocatalysts. This work sheds light on the importance of tuning the interlayer spacing to improve electrocatalytic activity.

Pauling-type adsorption of O2 induced electrocatalytic singlet oxygen production on N-CuO for organic pollutants degradation

Due to environmentally friendly operation and on-site productivity, electrocatalytic singlet oxygen (¹O₂) production via O₂ gas is of immense interest in environment purification. However, the side-on configuration of O₂ on the catalysts surface will lead to the formation of H₂O, which seriously limits the selectivity and activity of ¹O₂ production. Herein, we show a robust N-doped CuO (N–CuO) with Pauling-type (end-on) adsorption of O₂ at the N–Cu–O₃ sites for the selective generation of ¹O₂ under direct-current electric field. We propose that Pauling-type configuration of O₂ not only lowers the overall activation energy barrier, but also alters the reaction pathway to form ¹O₂ instead of H₂O, which is the key feature determining selectivity for the dissociation of Cu–O bonds rather than the O–O bonds. The proposed N dopant strategy is applicable to a series of transition metal oxides, providing a universal electrocatalysts design scheme for existing high-performance electrocatalytic ¹O₂ production.

Side-on configuration of O₂ on the catalysts conventionally leads to reduction of O₂ to water. Here, the authors propose a nitrogen doping strategy with Pauling-type adsorption of O₂ for selective electrocatalytic singlet oxygen production.

Recent advances in hollow nanomaterials with multiple dimensions for electrocatalytic water splitting

Electrocatalytic water splitting has great research prospects in the production of green hydrogen energy, and electrocatalysts are the prerequisite. As widely employed efficient electrocatalysts, hollow nanostructures have attracted a lot of research attention due to their excellent catalytic activity and structural stability. Moreover, the abundant catalytically active sites and tunable morphology also make hollow nanomaterials promising electrocatalysts for water splitting. Despite these advantages, the industrial applications of these hollow nanocatalysts are impeded by limitations like the lack of effective synthesis methods and unclear formation mechanisms. Therefore, extensive efforts have been devoted to the development of efficient synthesis strategies to boost the development of more efficient hollow electrocatalysts, and great progress has been achieved in recent years. To gain a better understanding of the rapid development of hollow nanocatalysts for water splitting, we herein organize a review to summarize the recent synthetic methods and advantages of hollow materials with different dimensions. The specific advantages of hollow nanomaterials in electrocatalytic water splitting, such as abundant active sites, a stable structure, high mass transfer efficiency, and reduced aggregation of catalytic particles, are also summarized. Finally, the challenges and prospects of hollow nanostructures with multiple dimensions in electrocatalytic water splitting are further explored.

Highly Active Si Sites Enabled by Negative Valent Ru for Electrocatalytic Hydrogen Evolution in LaRuSi

The discovery and identification of novel active sites are paramount for deepening the understanding of the catalytic mechanism and driving the development of remarkable electrocatalysts. Here, we reveal that the genuine active sites for the hydrogen evolution reaction (HER) in LaRuSi are Si sites, not the usually assumed Ru sites. Ru in LaRuSi has a peculiar negative valence state, which leads to strong hydrogen binding to Ru sites. Surprisingly, the Si sites have a Gibbs free energy of hydrogen adsorption that is near zero (0.063 eV). The moderate adsorption of hydrogen on Si sites during the HER process is also validated by in situ Raman analysis. Based on it, LaRuSi exhibits an overpotential of 72 mV at 10 mA cm^-2 in alkaline media, which is close to the benchmark of Pt/C. This work sheds light on the recognition of real active sites and the exploration of innovative silicide HER electrocatalysts.

Nanoscale Double-Heterojunctional Electrocatalyst for Hydrogen Evolution

The active sites and charge/mass transfer properties in electrocatalysts play vital roles in kinetics and thermodynamics of electrocatalysis, and impose direct impacts on electrocatalytic performance, which cannot be achieved by a simplex structure. As a prototype, the authors propose a double-heterojunctional nanostructure of NiS₂ /Ni₃ C@C containing NiS₂ /Ni₃ C and Ni₃ C/C heterojunctions as a general model to optimize the above issues and boost electrocatalytic performance. During the thermal reorganization, the in situ reaction between NiS₂ nanoparticles and carbon induces the formation of Ni₃ C between them and constructs tightly contacted two kinds of interfaces among the three components. The TEM and XPS reveal the intimately contacted three components and the as-constructed interacted dual interfaces, further confirming the formation of a porous double-heterojunctional nanostructure. Theoretical calculations uncover that the electron density redistribution occurs at Ni₃ C/C interface by spontaneous electron transfer from defected carbon to Ni₃ C and lower ΔG_H* achieves at NiS₂ /Ni₃ C interface by the concentrated interfacial charge density, which favors the simultaneous realization of high catalytic activity and rapid charge/mass transfer. When applied for hydrogen evolution reaction (HER), the porous double-heterojunctional NiS₂ /Ni₃ C@C exhibits excellent HER activity and durability among all pH values. Profoundly, this special double-heterojunctional structure can provide a new model for high-performance electrocatalysts and beyond.

Encapsulated ruthenium nanoparticles activated few-layer carbon frameworks as high robust oxygen evolution electrocatalysts in acidic media

Noble metals have been extensively employed as high active catalysts for oxygen evolution reaction (OER), are usually subjected to serious surface transformation and poor structural stability, especially in acid media, which need imperatively remedied. Herein, the interfacial engineering of Ru via few-layer carbon (Ru@FLC) was carried out, in which FLC can significantly suppress the corrosion of Ru in acid media, ensuring the efficient interfacial charge transport between Ru and FLC. As a result, a low overpotentials@10 mA cm^-2 of 258 mV and small Tafel slopes of 53.1 mV dec^-1 for oxygen evolution OER were achieved in acid media. DFT calculations disclose that outer FLC could induce charge redistribution and effectively optimize intermediates free energy adsorption, resulting in greatly reduce the energy barrier for OER. Our work may offer a new avenue to produce progressive OER electrocatalysts for energy-related applications in acid solution.

Oxygen Vacancies and Interface Engineering on Amorphous/Crystalline CrOx -Ni3 N Heterostructures toward High-Durability and Kinetically Accelerated Water Splitting

Manipulating catalytic active sites and reaction kinetics in alkaline media is crucial for rationally designing mighty water-splitting electrocatalysts with high efficiency. Herein, the coupling between oxygen vacancies and interface engineering is highlighted to fabricate a novel amorphous/crystalline CrO_x -Ni₃ N heterostructure grown on Ni foam for accelerating the alkaline hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). Density functional theory (DFT) calculations reveal that the electron transfer from amorphous CrO_x to Ni₃ N at the interfaces, and the optimized Gibbs free energies of H₂ O dissociation (ΔG_H-OH ) and H adsorption (ΔG_H ) in the amorphous/crystalline CrO_x -Ni₃ N heterostructure are conducive to the superior and stable HER activity. Experimental data confirm that numerous oxygen vacancies and amorphous/crystalline interfaces in the CrO_x -Ni₃ N catalysts are favorable for abundant accessible active sites and enhanced intrinsic activity, resulting in excellent catalytic performances for HER and OER. Additionally, the in situ reconstruction of CrO_x -Ni₃ N into highly active Ni₃ N/Ni(OH)₂ is responsible for the optimized OER performance in a long-term stability test. Eventually, an alkaline electrolyzer using CrO_x -Ni₃ N as both cathode and anode has a low cell voltage of 1.53 V at 10 mA cm^-2 , together with extraordinary durability for 500 h, revealing its potential in industrial applications.

Crystalline-Amorphous Interfaces Coupling of CoSe2 /CoP with Optimized d-Band Center and Boosted Electrocatalytic Hydrogen Evolution

Amorphous and heterojunction materials have been widely used in the field of electrocatalytic hydrogen evolution due to their unique physicochemical properties. However, the current used individual strategy still has limited effects. Hence efficient tailoring tactics with synergistic effect are highly desired. Herein, the authors have realized the deep optimization of catalytic activity by a constructing crystalline-amorphous CoSe₂ /CoP heterojunction. Benefiting from the strong electronic coupling at the interfaces, the d-band center of the material moves further down compared to its crystalline-crystalline counterpart, optimizing the valence state and the H adsorption of Co and lowering the kinetic barrier of hydrogen evolution reaction (HER). The heterojunction shows an overpotential of 65 mV to drive a current density of 10 mA cm^-2 in the acidic medium. Besides, it also shows competitive properties in both neutral and basic media. This work provides inspiration for optimizing the catalytic activity through combining a crystalline and amorphous heterojunction, which can be implemented for other transition metal compound electrocatalysts.

Electronic modulation of cobalt-molybdenum oxide via Te doping embedded in carbon matrix for superior overall water splitting

Developing heteroatom incorporation into the lattice of host materials as bifunctional electrocatalysts is an effective strategy to promote electrochemical water splitting but challenges remain for catalytic activity modulation. Herein, Te-doped...

Nitrogen-doped carbon encapsulating RuCo heterostructure for enhanced electrocatalytic overall water splitting

The kinetically sluggish electrochemical water splitting reaction still faces great challenges, and the rational design of excellent electrocatalysts is the key to solving the problem. Herein, an etching and pyrolysis...