Durable Multiblock Poly(biphenyl alkylene) Anion Exchange Membranes with Microphase Separation for Hydrogen Energy Conversion

Partially PEG-Grafted Poly(Terphenyl Piperidinium) Anion Exchange Membranes with Balanced Properties for Alkaline Fuel Cells

Poly(ethylene glycol) (PEG) or oligo (ethylene glycol) (OEG) grafted anion exchange membranes (AEMs) exhibit improved ionic conductivity, high alkaline stability, and subsequent boosted AEM fuel cell performance, but too much PEG/OEG side chains may can result in a reduction in the ion exchange capacity (IEC), which can have adverse effects on ion transport. Here, a series of partially PEG-grafted poly(terphenyl piperidinium) with different side chain length are synthesized using simple postpolymerization modification to produce AEMs with balanced properties. The polar and flexible PEG side chains are responsible for the controlled water uptake and swelling, superior hydroxide conductivity (122 mS cm-1 at 80 °C with an IEC of 1.99 mmol g-1), and enhanced alkaline stability compared to the reference sample without PEG grafts (PTP). More importantly, the performance of AEM fuel cell (AEMFC) with the membrane containing partial PEG side chains surpasses that with PTP membrane, demonstrating a highest peak power density of 1110 mW cm-2 at 80 °C under optimized conditions. This work provides a novel approach to the fabrication of high-performance AEM materials with balanced properties for alkaline fuel cell application.

Ultramicroporous crosslinked polyxanthene-poly(biphenyl piperidinium)-based anion exchange membranes for water electrolyzers operating under highly alkaline conditions

Anion exchange membrane water electrolyzers (AEMWEs) suffer from low efficiencies and durability, due to the unavailability of appropriate anion exchange membranes (AEM). Herein, a rigid ladder-like polyxanthene crosslinker was developed for the preparation of ultramicroporous crosslinked polyxanthene-poly(biphenyl piperidinium)-based AEMs. Due to the synergetic effects of their ultramicroporous structure and microphase-separation morphology, the crosslinked membranes showed high OH- conductivity (up to 163 mS cm-1 at 80 °C). Furthermore, these AEMs also exhibited moderate water uptake, excellent dimensional stability, and remarkable alkaline stability. The single-cell AEMWE based on QPBP-PX-15% and equipped with non-noble catalysts achieved a current density of 3000 mA cm-2 at 2.03 V (compared to PiperION's 2.26 V) in 6 M KOH solution at 80 °C, which outperformed many AEMWEs that used platinum-group-metal catalysts. Thus, the crosslinked AEMs developed in this study showed significant potential for application in AEMWEs fed with concentrated alkaline solutions.

Constructing Microporous Ion Exchange Membranes via Simple Hypercrosslinking for pH-Neutral Aqueous Organic Redox Flow Batteries

Ion exchange membranes (IEMs) play a critical role in aqueous organic redox flow batteries (AORFBs). Traditional IEMs that feature microphase-separated microstructures are well-developed and easily available but suffer from the conductivity/selectivity tradeoff. The emerging charged microporous polymer membranes show the potential to overcome this tradeoff, yet their commercialization is still hindered by tedious syntheses and demanding conditions. We herein combine the advantages of these two types of membrane materials via simple in situ hypercrosslinking of conventional IEMs into microporous ones. Such a concept is exemplified by the very cheap commercial quaternized polyphenylene oxide membrane. The hypercrosslinking treatment turns poor-performance membranes into high-performance ones, as demonstrated by the above 10-fold selectivity enhancement and much-improved conductivities that more than doubled. This turn is also confirmed by the effective and stable pH-neutral AORFB with decreased membrane resistance and at least an order of magnitude lower capacity loss rate. This battery shows advantages over other reported AORFBs in terms of a low capacity loss rate (0.0017 % per cycle) at high current density. This work provides an economically feasible method for designing AORFB-oriented membranes with microporosity.

Bioadhesive-Inspired Ionomer for Membrane Electrode Assembly Interface Reinforcement in Fuel Cells

Anion exchange membrane fuel cells promise a sustainable and ecofriendly energy conversion pathway yet suffer from insufficient performance and durability. Drawing inspiration from mussel foot adhesion proteins for the first time, we herein demonstrate catechol-modified ionomers that synergistically reinforce the membrane electrode assembly interface and triple-phase boundary inside catalyst layers. The resulting ionomers present exceptional alkaline stability with only slight ionic conductivity declines after treatment in 2 M NaOH aqueous solution at 80 °C for 2500 h. Adopting catechol-modified ionomer as both anion exchange membrane and binder achieves a single-cell performance increase of 34%, and more importantly, endows fuel cell operation at a current density of 0.4 A cm-2 for over 300 h with negligible performance degradation (with a cell voltage decay rate of 0.03 mV h-1). Combining theoretical and experimental investigations, we reveal the molecular adhesion mechanism between the catechol-modified ionomer and Pt catalyst and illuminate the effect on the catalyst layer microstructure. Of fundamental interest, this bioadhesive-inspired strategy is critical to enabling knowledge-driven ionomer design and is promising for diverse membrane electrode assembly configurational applications.

High-Performance Anion Exchange Membrane Water Electrolyzers Enabled by Highly Gas Permeable and Dimensionally Stable Anion Exchange Ionomers

Designing suitable anion exchange ionomers is critical to improving the performance and in situ durability of anion exchange membrane water electrolyzers (AEMWEs) as one of the promising devices for producing green hydrogen. Herein, highly gas-permeable and dimensionally stable anion exchange ionomers (QC6xBA and QC6xPA) are developed, in which bulky cyclohexyl (C6) groups are introduced into the polymer backbones. QC650BA-2.1 containing 50 mol% C6 composition shows 16.6 times higher H2 permeability and 22.3 times higher O2 permeability than that of QC60BA-2.1 without C6 groups. Through-plane swelling of QC650BA-2.1 decreases to 12.5% from 31.1% (QC60BA-2.1) while OH- conductivity slightly decreases (64.9 and 56.2 mS cm-1 for QC60BA-2.1 and QC650BA-2.1, respectively, at 30 °C). The water electrolysis cell using the highly gas permeable QC650BA-2.1 ionomer and Ni0.8Co0.2O in the anode catalyst layer achieves two times higher performance (2.0 A cm-2 at 1.69 V, IR-included) than those of the previous cell using in-house ionomer (QPAF-4-2.0) (1.0 A cm-2 at 1.69 V, IR-included). During 1000 h operation at 1.0 A cm-2, the QC650BA-2.1 cell exhibits nearly constant cell voltage with a decay rate of 1.1 µV h-1 after the initial increase of the cell voltage, proving the effectiveness of the highly gas permeable and dimensionally stable ionomer in AEMWEs.

TRPM4-Inspired Polymeric Nanochannels with Preferential Cation Transport for High-Efficiency Salinity-Gradient Energy Conversion

Biological ion channels exhibit switchable cation transport with ultrahigh selectivity for efficient energy conversion, such as Ca2+-activated TRPM4 channels tuned by cation-π interactions, but achieving an analogous highly selective function is challenging in artificial nanochannels. Here, we design a TRPM4-inspired cation-selective nanochannel (CN) assembled by two poly(ether sulfone)s, respectively, with sulfonate acid and indole moieties, which act as cation-selective activators to manage Na+/Cl- selectivity via ionic and cation-π interactions. The cation selectivity of CNs can be activated by Na+, and thereby the Na+ transference number significantly improves from 0.720 to 0.982 (Na+/Cl- selectivity ratio from 2.6 to 54.6) under a 50-fold salinity gradient, surpassing the K+ transference number (0.886) and Li+ transference number (0.900). The TRPM4-inspired nanochannel membrane enabled a maximum output power density of 5.7 W m-2 for salinity-gradient power harvesting. Moreover, a record energy conversion efficiency of up to 46.5% is provided, superior to most nanochannel membranes (below 30%). This work proposes a novel strategy to biomimetic nanochannels for highly selective cation transport and high-efficiency salinity-gradient energy conversion.

Ultrathin Free-Standing Porous Aromatic Framework Membranes for Efficient Anion Transport

Porous aromatic frameworks (PAFs) show promising potential in anionic conduction due to their high stability and customizable functionality. However, the insolubility of most PAFs presents a significant challenge in their processing into membranes and subsequent applications. In this study, continuous PAF membranes with adjustable thickness were successfully created using liquid-solid interfacial polymerization. The rigid backbone and the stable C-C coupling endow PAF membrane with superior chemical and dimensional stabilities over most conventional polymer membranes. Different quaternary ammonium functionalities were anchored to the backbone through flexible alkyl chains with tunable length. The optimal PAF membrane exhibited an OH- conductivity of 356.6 mS ⋅ cm-1 at 80 °C and 98 % relative humidity. Additionally, the PAF membrane exhibited outstanding alkaline stability, retaining 95 % of its OH- conductivity after 1000 hours in 1 M NaOH. To the best of our knowledge, this is the first application of PAF materials in anion exchange membranes, achieving the highest OH- conductivity and exceptional chemical/dimensional stability. This work provides the possibility for the potential of PAF materials in anionic conductive membranes.

A Hydrophilic Polyethylene Glycol-Blended Anion Exchange Membrane to Facilitate the Migration of Hydroxide Ions

As one of the most important sources for green hydrogen, anion exchange membrane water electrolyzers (AEMWEs) have been developing rapidly in recent decades. Among these components, anion exchange membranes (AEMs) with high ionic conductivity and good stability play an important role in the performance of AEMWEs. In this study, we have developed a simple blending method to fabricate the blended membrane ImPSF-PEGx via the introduction of a hydrophilic PEG into the PSF-based ionic polymer. Given their hydrophilicity and coordination properties, the introduced PEGs are beneficial in assembling the ionic groups to form the ion-conducting channels. Moreover, an asymmetric structure is observed in ImPSF-PEGx membranes with a layer of finger-like cracks at the upper surface because PEGs can act as pore-forming agents. During the study, the ImPSF-PEGx membranes exhibited higher water uptake and ionic conductivity with lower swelling ratios and much better mechanical properties in comparison to the pristine ImPSF membrane. The ImPSF-PEG1000 membrane showed the best overall performance among the membranes with higher ionic conductivity (82.6 mS cm-1 at 80 °C), which was approximately two times higher than the conductivity of ImPSF, and demonstrated better mechanical and alkaline stability. The alkaline water electrolyzer assembled by ImPSF-PEG1000 achieved a current density of 606 mA cm-2 at 80 °C under conditions of 1 M KOH and 2.06 V, and maintained an essentially unchanged performance after 48 h running.

Enhancing Ni/Co Activity by Neighboring Pt Atoms in NiCoP/MXene Electrocatalyst for Alkaline Hydrogen Evolution

Density functional theory (DFT) calculations demonstrate neighboring Pt atoms can enhance the metal activity of NiCoP for hydrogen evolution reaction (HER). However, it remains a great challenge to link Pt and NiCoP. Herein, we introduced curvature of bowl-like structure to construct Pt/NiCoP interface by adding a minimal 1 ‰-molar-ratio Pt. The as-prepared sample only requires an overpotential of 26.5 and 181.6 mV to accordingly achieve the current density of 10 and 500 mA cm-2 in 1 M KOH. The water dissociation energy barrier (Ea) has a ~43 % decrease compared with NiCoP counterpart. It also shows an ultrahigh stability with a small degradation rate of 10.6 μV h-1 at harsh conditions (500 mA cm-2 and 50 °C) after 3000 hrs. X-ray photoelectron spectroscopy (XPS), soft X-ray absorption spectroscopy (sXAS), and X-ray absorption fine structure (XAFS) verify the interface electron transfer lowers the valence state of Co/Ni and activates them. DFT calculations also confirm the catalytic transition step of NiCoP can change from Heyrovsky (2.71 eV) to Tafel step (0.51 eV) in the neighborhood of Pt, in accord with the result of the improved Hads at the interface disclosed by in situ electrochemical impedance spectroscopy (EIS) and scanning electrochemical microscopy (SECM) tests.

Stable Anion Exchange Membrane Bearing Quinuclidinium for High-performance Water Electrolysis

Anion exchange membranes (AEMs) are core components in anion exchange membrane water electrolyzers (AEM-WEs). However, the stability of functional quaternary ammonium cations, especially under high temperatures and harsh alkaline conditions, seriously affects their performance and durability. Herein, we synthesized a 1-methyl-3,3-diphenylquinuclidinium molecular building unit. Density functional theory (DFT) calculations and accelerated aging analysis indicated that the quinine ring structure was exceedingly stable, and the SN2 degradation mechanism dominated. Through acid-catalyzed Friedel-Crafts polymerization, a series of branched poly(aryl-quinuclidinium) (PAQ-x) AEMs with controllable molecular weight and adjustable ion exchange capacity (IEC) were prepared. The stable quinine structure in PAQ-x was verified and retained in the ex situ alkaline stability. Furthermore, the branched polymer structure reduces the swelling rate and water uptake to achieve a tradeoff between dimensional stability and ionic conductivity, significantly improving the membrane's overall performance. Importantly, PAQ-5 was used in non-noble metal-based AEM-WE, achieving a high current density of 8 A cm-2 at 2 V and excellent stability over 2446 h in a gradient constant current test. Based on the excellent alkaline stability of this diaryl-quinuclidinium group, it can be further considered as a multifunctional building unit to create multi-topological polymers for energy conversion devices used in alkaline environments.

Ultramicroporous Tröger's Base Framework Membranes for pH-Neutral Aqueous Organic Redox Flow Batteries

Processable polymers of intrinsic microporosity (PIMs) are emerging as promising candidates for next-generation ion exchange membranes (IEMs). However, especially with high ion exchange capacity (IEC), IEMs derived from PIMs suffer from severe swelling, thus, resulting in decreased selectivity. To solve this problem, we report ultramicroporous polymer framework membranes constructed with rigid Tröger's Base network chains, which are fabricated via an organic sol-gel process. These membranes demonstrate excellent antiswelling, with swelling ratios below 4.5% at a high IEC of 2.09 mmol g-1, outperforming currently reported PIM membranes. The rigid ultramicropore confinement and charged modification of pore channels endow membranes with both very high size-exclusion selectivity and competitive ion conductivity. The membranes thus enable the efficient and stable operation of pH-neutral aqueous organic redox flow batteries (AORFBs). This work presents the advantages of polymer framework materials as IEMs and calls for increasing attention to extending their varieties and utilization in other applications.

Long-lifespan Zinc-ion Capacitors Enabled by Anodes Integrated with Interconnected Mesoporous Chitosan Membranes through Electrophoresis-driven Phase Separation

The advancement of highly secure and inexpensive aqueous zinc ion energy storage devices is impeded by issues, including dendrite growth, hydrogen evolution and corrosion of zinc anodes. It is essential to modify the interface of zinc anodes that homogenizes ion flux and facilitates highly reversible zinc planarized deposition and stripping. Herein, by coupling zinc ion coordination with acid-base neutralization under the driving of electrophoresis, manageable mesoscopic phase separation for constructing chitosan frameworks was achieved, thereby fabricating interconnected mesoporous chitosan membranes based heterogeneous quasi-solid-state electrolytes integrated with anodes. The framework is constructed by twisted chitosan nanofiber bundles, forming a three-dimensional continuous spindle-shaped pore structure. With this framework, the electrolyte provides exceptional ion conductivity of 25.1 mS cm-1 , with a puncture resistance strength of 2.3 GPa. In addition, the amino groups of chitosan molecule can make the surface of the framework positively charged. Thus, reversible zinc planarized deposition is successfully induced by the synergistic effect of stress constraint and electrostatic modulation. As a result, as-assembled zinc ion capacitor has an excellent cycle life and sustains the capacity by over 95 % after 20000 cycles at a current density of 5 A g-1 . This research presents a constructive strategy for stable electrolytes-integrated zinc anodes.

"Fishbone" Design of Amino/N-Spirocyclic Cations toward High-Performance Poly(triphenylene piperidine) Anion-Exchange Membranes for Fuel Cells

N-Spirocyclic cations have excellent alkali resistance stability, and precise design of the structure of N-spirocyclic anion-exchange membranes (AEMs) improves their comprehensive performance. Here, we design and synthesize high-performance poly(triphenylene piperidine) membranes based on the "fishbone" design of amino/N-spirocyclic cations. The "fishbone" design does not disrupt the overall stabilized conformation but promotes a microphase separation structure, while exerting the synergistic effect of piperidine cations and spirocyclic cations, resulting in a membrane with good conductivity and alkali resistance stability. The hydroxide conductivity of the QPTPip-ASU-X membrane reached up to 133.5 mS cm-1 at 80 °C. The QPTPip-ASU-15 membrane was immersed in a 2 M NaOH solution at 80 °C for 1200 h, and the conductivity was maintained at 91.02%. In addition, the QPTPip-ASU-5 membrane had the highest peak power density of 255 mW cm-2.

Advanced Architectures of Air Electrodes in Zinc-Air Batteries and Hydrogen Fuel Cells

The air electrode is an essential component of air-demanding energy storage/conversion devices, such as zinc-air batteries (ZABs) and hydrogen fuel cells (HFCs), which determines the output power and stability of the devices. Despite atom-level modulation in catalyst design being recently achieved, the air electrodes have received much less attention, causing a stagnation in the development of air-demanding equipment. Herein, the evolution of air electrodes for ZABs and HFCs from the early stages to current requirements is reviewed. In addition, the operation mechanism and the corresponding electrocatalytic mechanisms of ZABs are summarized. In particular, by clarifying the air electrode interfaces of ZABs at different scales, several approaches to improve the air electrode in rechargeable ZABs are reviewed, including innovative electrode structures and bifunctional oxygen catalysts. Afterward, the operating mechanisms of proton-exchange-membrane fuel cells (PEMFCs) and anion-exchange-membrane fuel cells (AEMFCs) are explained. Subsequently, the strategies employed to enhance the efficiency of the membrane electrode assembly (MEA) in PEMFCs and AEMFCs, respectively, are highlighted and discussed in detail. Last, the prospects for air electrodes in ZABs and HFCs are considered by discussing the main challenges. The aim of this review is to facilitate the industrialization of ZABs and HFCs.