Synthesis and characterization of a new nanocomposite (FeW11 V@CTAB-MMT) as an efficient heterogeneous catalyst for oxidative desulfurization of gasoline

New magnetic nanocomposites based on hexafrite and keggin-type -type heteropolyanions: Synthesized and characterized for removal of environmental pollutants

This research paper details the creation of innovative nanocomposites using the sol-gel technique, incorporating polyoxometalates SiW9Ba3 to stabilize ceramic particles of strontium ferrite (SrFe12O19) polymer and Chitosan (CS). The identification and confirmation of the nanocomposites obtained at each stage were carried out through the use of FT-IR, EDX, XRD, and FESEM analyses. To evaluate their ability to remove organic dyes, we analyzed the catalytic activity of these nanocomposites during photocatalytic detoxification procedures. With its exceptional photocatalytic properties, the nanocomposite (SiW9Ba3@SrFe12O19@Cs) was able to remove estamipride poison at an impressive rate of 85 % and xylene dye solution at an even higher rate of 98 %. In addition, an extensive examination was undertaken to explore the primary variables that influence process efficiency. The study suggests that ceramic nanocomposites incorporating heteropolyoxometalate may offer a viable approach to effectively eradicate pollutants from the environment.

Design of a new nanocomposite based on Keggin-type [ZnW12O40]6- anionic cluster anchored on NiZn2O4 ceramics as a promising material towards the electrocatalytic hydrogen storage

Extensive research efforts have been dedicated to developing electrode materials with high capacity to address the increasing complexities arising from the energy crisis. Herein, a new nanocomposite was synthesized via the sol-gel method by immobilizing K6ZnW12O40 within the surface of NiZn2O4. ZnW12O40@NiZn2O4 was characterized by FT-IR, UV-Vis, XRD, SEM, EDX, BET, and TGA-DTG methods. The electrochemical characteristics of the materials were examined using cyclic voltammogram (CV) and charge-discharge chronopotentiometry (CHP) techniques. Multiple factors affecting the hydrogen storage capacity, including current density (j), surface area of the copper foam, and the consequences of repeated cycles of hydrogen adsorption-desorption were evaluated. The initial cycle led to an impressive hydrogen discharge capability of 340 mAh/g, which subsequently increased to 900 mAh/g after 20 cycles with a current density of 2 mA in 6.0 M KOH medium. The surface area and the electrocatalytic characteristics of the nanoparticles contribute to facilitate the formation of electrons and provide good diffusion channels for the movement of electrolyte ions throughout the charge-discharge procedure.

Periodate-Mediated Aerobic Oxidation of Sulfides over a Bifunctional Porphyrin-polyoxometalate Catalyst: Photosensitized Singlet Oxygen Oxidation of Iodate to Periodate

Regeneration of terminal oxidants by molecular oxygen in metal-catalyzed oxidations of organic substrates has the advantage of avoiding the use of stoichiometric amounts of hazardous and/or expensive reagents to meet (some of) the green chemistry requirements. In the present study, photosensitized singlet oxygen oxidation of iodate to periodate has been used to regenerate the oxidant in polyoxometalate (POM)-catalyzed oxidation of sulfides to sulfoxides with periodate in water. To the best of our knowledge, it is the first report on singlet oxygen oxidation of iodate to periodate. In order to determine the contribution of photooxidation and oxidation pathways in the formation of sulfoxide, the oxidation of diphenyl sulfide with a very low reactivity toward aerobic photooxidation was studied; a sevenfold increase in the conversion of the sulfide to the diphenyl sulfoxide was observed for the reaction conducted in the presence of H2TMPyP-PW12O40/IO3-/O2/hν compared to that in the presence of H2TMPyP-PW12O40/O2/hν. Also, under the same conditions, a ca. 1.5-fold increase was observed in the case of methyl phenyl sulfide, which shows high reactivity toward both the oxidation and photooxidation reactions. A porphyrin-POM nanocomposite formed by the electrostatic immobilization of meso-tetra(N-methylpyridinium-4-yl)porphyrin (H2TMPyP) on PW12O40 was employed for the one-pot oxidation and photooxidation reactions. Field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), diffuse-reflectance UV-vis spectroscopy, thermal gravimetric analysis, and Fourier transform infrared were used to characterize the formation of the hybrid compound. An average particle size of 42 nm was estimated for H2TMPyP-PW12O40 from XRD peak broadening using the Scherrer equation. Also, FESEM images showed the formation of nearly spherical nanoparticles with a size of ca. 200 nm. The redshift of the Soret band of H2TMPyP upon immobilization on POM was attributed to strong N-H···O hydrogen-bond interactions between POM and porphyrin.

Biodesulfurization of Dibenzothiophene by Decorating Rhodococcus erythropolis IGTS8 Using Montmorillonite/Graphitic Carbon Nitride

Fossil fuels are the main sources of human energy, but their combustion releases toxic compounds of sulfur oxide. In the oil industry, using the optimal methods to eliminate sulfur compounds from fossil fuels is a very important issue. In this study, the performance of montmorillonite/graphitic carbon nitride (a new hybrid nanostructure) in increasing the biodesulfurization activity of Rhodococcus erythropolis IGTS8 was investigated. X-ray diffraction, Fourier-transform infrared spectroscopy, field emission scanning electron microscopy and transmission electron microscopy were used for the characterization of the nanoparticles. The effective factors in this process were determined. Optimum conditions for microorganisms were designed using the Design Expert software. Experiments were performed in a flask. The results indicated that the biodesulfurization activity of a microorganism in the presence of the nanostructure increases by 52%. In addition, in the presence of the nanostructure, the effective factors are: 1. concentration of the nanostructure; 2. concentration of sulfur; 3. cell concentration. In the absence of the nanostructure, the only effective factor is the concentration of sulfur. Through analysis of variance, the proposed models were presented to determine the concentration of the 2-hydroxy biphenyl produced by the microorganisms (biodesulfurization activity) in the presence and absence of the nanostructure. The proposed models were highly acceptable and consistent with experimental data. The results of a Gibbs assay showed that the biodesulfurization efficiency of in the presence of the nanostructure was increased by about 52%, which is a very satisfactory result. The biodesulfurization activity of decorated cells in a bioreactor showed a significant increase compared with nondecorated cells. Almost a two-fold improvement in biodesulfurization activity was obtained for decorated cells compared with free cells.

Development of reduced graphene oxide-supported novel hybrid nanomaterials (Bi2WO6@rGO and Cu-WO4@rGO) for green and efficient oxidative desulfurization of model fuel oil for environmental depollution

For the first time, two new kinds of inorganic-organic hybrid nanomaterials (Bi₂WO₆@rGO and Cu-WO₄@rGO) were fabricated by simple hydrothermal treatment and employed for green and efficient oxidative desulfurization of real fuel. The characterization of newly synthesized nanocomposites was performed by SEM, EDX, P-XRD, FT-IR and TGA. SEM and XRD analyses revealed well decoration of dopants (Cu-WO₄ and Bi-WO₃) on the surface of rGO with a crystallite size of <50 nm. The catalytic activity of both nanocatalysts was examined for model (dibenzothiophene) and real fuel (kerosene and diesel) by oxidative desulfurization route. Experimental findings revealed a high efficiency of over 90% under optimal reaction conditions of 0.1 g catalyst, 1 mL of oxidant, and 100 mg/L after 120 min at 30 °C. The major factors affecting desulfurization efficiency (time, temperature, catalyst amount, dibenzothiophene (DBT) concentration and amount of oxidant) and kinetic studies were described. The DBT removal via oxidative desulfurization followed pseudo first-order kinetics with an activation energy of 14.57 and 16.91 kJ/mol for Cu-WO₄@rGO and Bi₂WO₆@rGO, respectively. The prepared catalysts showed promising reusability for the ODS process up to 5 times with no significant decrease in efficiency. In conclusion, the findings confirm the robustness of newly prepared nanocomposite for efficient production of sulfur-free oil.

Sono-oxidative desulfurization of fuels using heterogeneous and homogeneous catalysts: A comprehensive review

Recently, environmental pollution has increased significantly due to petroleum-based fuels widely used in vehicles. This environmental pollution is mainly due to the acidic SO2 gas generated by the combustion of fuels and emitted into the atmosphere. SO2 gas causes not only acid rain but also corrosion of metal parts of engines in vehicles. In addition, it functions as a catalyst poison in catalytic converters in exhaust system. Due to these damages, strict regulations have been introduced to reduce the amount of sulfur in fuels. As of 2005, the permissible amount of sulfur in diesel fuels in Europe and America has been limited to 10 and 15 ppm by weight, respectively. Due to the decreasing oil reserves in the world, high viscosity petroleums containing high sulfur and heavier fractions (i.e., low-quality oils) are increasing, thus making desulfurization difficult and leading to high costly process. Since time and economic loss are very important today, these two terms have to be reduced to a minimum. Recently, ultrasound wave in ODS shown as an alternative to HDS is utilized to further increase desulfurization in shorter times. Ultrasound wave locally creates high temperatures and high pressures (hot-spot theory) in liquid, causing the desulfurization reaction to accelerate further. In this review, the advantages and difficulties of oxidative desulfurization, the economics of ultrasound-assisted oxidative desulfurization are summarized and recommendations for improving the process are presented.

Nanocatalysts for Oxidative Desulfurization of Liquid Fuel: Modern Solutions and the Perspectives of Application in Hybrid Chemical-Biocatalytic Processes

In this paper, the current advantages and disadvantages of using metal-containing nanocatalysts (NCs) for deep chemical oxidative desulfurization (ODS) of liquid fuels are reviewed. A similar analysis is performed for the oxidative biodesulfurization of oil along the 4S-pathway, catalyzed by various aerobic bacterial cells of microorganisms. The preferences of using NCs for the oxidation of organic sulfur-containing compounds in various oil fractions seem obvious. The text discusses the development of new chemical and biocatalytic approaches to ODS, including the use of both heterogeneous NCs and anaerobic microbial biocatalysts that catalyze the reduction of chemically oxidized sulfur-containing compounds in the framework of methanogenesis. The addition of anaerobic biocatalytic stages to the ODS of liquid fuel based on NCs leads to the emergence of hybrid technologies that improve both the environmental characteristics and the economic efficiency of the overall process. The bioconversion of sulfur-containing extracts from fuels with accompanying hydrocarbon residues into biogas containing valuable components for the implementation of C-1 green chemistry processes, such as CH4, CO2, or H2, looks attractive for the implementation of such a hybrid process.