Wet spinning of cellulose from ionic liquid solutions-viscometry and mechanical performance

High-Strength Regenerated Cellulose Fiber Reinforced with Cellulose Nanofibril and Nanosilica

In this study, a novel type of high-strength regenerated cellulose composite fiber reinforced with cellulose nanofibrils (CNFs) and nanosilica (nano-SiO₂) was prepared. Adding 1% CNF and 1% nano-SiO₂ to pulp/AMIMCl improved the tensile strength of the composite cellulose by 47.46%. The surface of the regenerated fiber exhibited a scaly structure with pores, which could be reduced by adding CNF and nano-SiO₂, resulting in the enhancement of physical strength of regenerated fibers. The cellulose/AMIMCl mixture with or without the addition of nanomaterials performed as shear thinning fluids, also known as "pseudoplastic" fluids. Increasing the temperature lowered the viscosity. The yield stress and viscosity sequences were as follows: RCF-CNF² > RCF-CNF²-SiO₂² > RCF-SiO₂² > RCF > RCF-CNF¹-SiO₂¹. Under the same oscillation frequency, G' and G" decreased with the increase of temperature, which indicated a reduction in viscoelasticity. A preferred cellulose/AMIMCl mixture was obtained with the addition of 1% CNF and 1% nano-SiO₂, by which the viscosity and shear stress of the adhesive were significantly reduced at 80 °C.

Coaxial Spinning of All-Cellulose Systems for Enhanced Toughness: Filaments of Oxidized Nanofibrils Sheathed in Cellulose II Regenerated from a Protic Ionic Liquid

Hydrogels of TEMPO-oxidized nanocellulose were stabilized for dry-jet wet spinning using a shell of cellulose dissolved in 1,5-diazabicyclo[4.3.0]non-5-enium propionate ([DBNH][CO₂Et]), a protic ionic liquid (PIL). Coagulation in an acidic water bath resulted in continuous core-shell filaments (CSFs) that were tough and flexible with an average dry (and wet) toughness of ∼11 (2) MJ·m^-3 and elongation of ∼9 (14) %. The CSF morphology, chemical composition, thermal stability, crystallinity, and bacterial activity were assessed using scanning electron microscopy with energy-dispersive X-ray spectroscopy, liquid-state nuclear magnetic resonance, Fourier transform infrared spectroscopy, thermogravimetric analysis, pyrolysis gas chromatography-mass spectrometry, wide-angle X-ray scattering, and bacterial cell culturing, respectively. The coaxial wet spinning yields PIL-free systems carrying on the surface the cellulose II polymorph, which not only enhances the toughness of the filaments but facilities their functionalization.

Composite fibers prepared from multi-walled carbon nanotubes/cellulose dispersed/dissolved in ammonium/dimethyl sulfoxide mixed solvent

A co-dispersion of cellulose and MWCNTs was prepared in a TBAA/DMSO solvent mixture and then used to prepare composite fibers.

Development of a novel cellulose/duck feather composite fibre regenerated in ionic liquid

By blending cellulose and duck feather in the common solvent 1-allyl-3-methylimidazoloium chloride, a regenerated composite fibre has been developed with improved fibres over regenerated cellulose fibres (RCF). The mechanical properties of composite fibre was shown to be better than RCF with a 63.7% improvement in tensile strain. Here, we thoroughly characterise the composite fibre and show that the composite fibre has many advantages over RCFs both from a spinning perspective and as a regenerated fibre.

High-Strength Composite Fibers from Cellulose-Lignin Blends Regenerated from Ionic Liquid Solution

Composite fibres that contain cellulose and lignin were produced from ionic liquid solutions by dry-jet wet spinning. Eucalyptus dissolving pulp and organosolv/kraft lignin blends in different ratios were dissolved in the ionic liquid 1,5-diazabicyclo[4.3.0]non-5-enium acetate to prepare a spinning dope from which composite fibres were spun successfully. The composite fibres had a high strength with slightly decreasing values for fibres with an increasing share of lignin, which is because of the reduction in crystallinity. The total orientation of composite fibres and SEM images show morphological changes caused by the presence of lignin. The hydrophobic contribution of lignin reduced the vapour adsorption in the fibre. Thermogravimetric analysis curves of the composite fibres reveal the positive effect of the lignin on the carbonisation yield. Finally, the composite fibre was found to be a potential raw material for textile manufacturing and as a precursor for carbon fibre production.

Shear dependent viscosity of poly(ethylene oxide) in two protic ionic liquids

Steady shear viscosity measurements have been performed on 100 kDa poly(ethylene oxide) (PEO) dissolved in the protic ionic liquids ethylammonium nitrate (EAN) and propylammonium nitrate (PAN) and in water. The zero shear viscosity in all three solvents increases with polymer concentration, falling into three concentration regimes corresponding to dilute, semi-dilute and network solutions. Huggins plots reveal three distinct solvent conditions: good (water), good-theta (EAN) and theta (PAN). However, differences in the transition concentrations, power law behaviour of the viscosities, and relaxation times arising from shear thinning in the two ILs can be directly related to the effects of solvent nanostructure.