Optimization and investigation of the governing parameters in electrospinning the home-made poly(l-lactide-co-ε-caprolactone-diOH)

3D network super-hydrophobic hexafluorbisphenol A poly(aryl ether ketone) membrane prepared by one-step electrospraying

Novel super-hydrophobic poly(aryl ether ketone) (PAEK) membranes have been firstly prepared by modifying ordinary PAEK into hexafluorbisphenol A-PAEK through traditional nucleophilic condensation polymerization and subsequently simple electrospraying technique. With the solution concentration increased, the micromorphology exhibited nanofibers, nanofiber with spindles, 3D network with microspheres embedded, microspheres and dense films, successively. The static water contact angle increased from 99° to 155°, while the sliding angle from 1.3° to 6.8° (±1°), in which the 3D network presented the strongest super-hydrophobicity. After 200 h of water flushing, the rough surface structure and super-hydrophobicity of the membranes were well retained. Moreover, the membrane exhibited wonderful self-cleaning property, oil/water separation property, and stability due to the hierarchical micro/nanostructures. This work provides a new route for the creation of super-hydrophobic high performance engineering plastic fabrics with the potential values in large-scale application of filtration, oil/water separation, and antifouling.

Electrospinning of poly(lactic acid)/polycaprolactone blends: investigation of the governing parameters and biocompatibility

Blends of poly(lactic acid)/polycaprolactone (PLA/PCL) were electrospun under various conditions to study the influence of solution concentration, feed rate and voltage supply on the morphology of the nanofibers. To improve compatibility and to help produce fine electrospun nanofibers, an L-lactide/caprolactone (LACL) copolymer was introduced as a compatibilizer in the PLA/PCL blends. It was found that the solution concentration was a principal governing factor. The mean diameter of the fibers increased with the solution concentration, feed rate and voltage. Too high of a concentration and feed rate caused the fibers to stick to each other. A slow feed rate, 10% solution concentration, and 20 kV voltage were capable of producing thin, smooth and uniform fibers. Preliminary biocompatibility assays of the nanofibers were conducted with NIH 3T3 cells. The cells grown on the nanofiber blend exhibited spindle-like morphologies. The addition of PCL and LACL copolymer was found to improve the biocompatibility of PLA nanofibers, suggesting their potential application as cell culture scaffolds.

A review of evolution of electrospun tissue engineering scaffold: From two dimensions to three dimensions

The potential of electrospinning process to fabricate ultrafine fibers as building blocks for tissue engineering scaffolds is well recognized. The scaffold construct produced by electrospinning process depends on the quality of the fibers. In electrospinning, material selection and parameter setting are among many factors that contribute to the quality of the ultrafine fibers, which eventually determine the performance of the tissue engineering scaffolds. The major challenge of conventional electrospun scaffolds is the nature of electrospinning process which can only produce two-dimensional electrospun mats, hence limiting their applications. Researchers have started to focus on overcoming this limitation by combining electrospinning with other techniques to fabricate three-dimensional scaffold constructs. This article reviews various polymeric materials and their composites/blends that have been successfully electrospun for tissue engineering scaffolds, their mechanical properties, and the various parameters settings that influence the fiber morphology. This review also highlights the secondary processes to electrospinning that have been used to develop three-dimensional tissue engineering scaffolds as well as the steps undertaken to overcome electrospinning limitations.

Electrospun carboxylic-functionalized poly(arylene ether ketone) ultrafine fibers

As a high-performance polymer, carboxylic-functionalized poly(arylene ether ketone)s (PCA-PAEK) was electrospun into ultrafine fibers and characterized. To optimize the process, a set of experiments were designed. As a result, the optimum condition was obtained and the polymer concentration was determined as the most important factor. Incidentally, the PCA-PAEK fibers were found to exhibit superabsorbent behavior. In order to investigate processing characteristics, PCA-PAEK fibers fabricated from different solution concentrations were employed and characterized. The results showed that porosity and changes in water contact angle and water absorbency decreased with an increase in concentration. In addition to a high water absorption capacity, the fibers exhibited good water retention and repeated water absorbency as well. The study on kinetics of water absorption and swelling behavior showed that the mechanism was dependent on the polymer concentration from which the fibers were electrospun. Moreover, both dry and wet PCA-PAEK fibers showed high mechanical properties. Due to these properties, the PCA-PAEK ultrafine fibers are potentially useful as a water-absorbent material.

High-effective preparation of ultrafine poly-(l-lactide-co-∊-caprolactone-diOH) fibers containing silver nanoparticles

A novel method utilizing combination of N, N-dimethylformamide (DMF) and ultraviolet (UV) irradiation to reduce silver (Ag+) ions in situ in ultrafine poly-(l-lactide-co- ∊-caprolactone-diOH) (PCLA) fibers was developed. Compared with traditional solvent reduction method, the new method exhibited much higher efficiency. UV–visible spectra indicated that the addition of UV irradiation could shorten the reaction time dramatically. Transmission electron microscope and x-ray photoelectron spectroscopy results demonstrated that the new method had produced a larger number of uniform Ag nanoparticles (AgNPs). After statistical analysis, their mean size was determined as 6.96 nm, which was smaller than that of traditional AgNPs. In addition, as a biodegradable polymer, PCLA was first used to carry AgNPs. It was found that PCLA can be a stabilizing agent of Ag+ ions. Therefore, the formation mechanism of AgNPs with larger number and smaller size can be determined.