The effect of graft copolymers of maleic anhydride and epoxy resin on the mechanical properties and morphology of PP/ABS blends

Impact of PP Impurities on ABS Tensile Properties: Computational Mechanical Modelling Aspects

Recycling of plastics is hindered by their important variety and strong incompatibility. However, sorting technologies bear costs and meet limits. Very high purities (<2 wt%) are difficult to reach. Yet, such rates may be detrimental to functional properties. In this work, an ABS matrix (major plastic in Waste of Electrical and Electronic Equipments) was filled with 4 wt% of PP to mimic impurities in ABS after recycling. PP-g-MA was introduced in the blend to improve the compatibility. A finite element model was developed from the mechanical behavior of each component. ABS and PP were individually characterized from tensile tests instrumented with photomechanics and their behaviors were modelled through a set of numerical parameters (elasto-visco-plasticity with a Gurson's criterion behavior). Comparison between the determinist model results and the experimental data (strength, volumetric variation) shows that this type of modelling could be a predictive tool in order to anticipate composite mechanical properties and to understand micromechanisms of deformation (damage, cavitation). The main result is that PP introduced at 4 wt% into ABS does not alter the static mechanical properties despite polymers incompatibility. The addition of PP-g-MA modifies the local properties and possibly conduct to a premature breakage of the polymer blend.

Degradation of Styrenic Plastics during Recycling: Accommodation of PP within ABS after WEEE Plastics Imperfect Sorting

With the development of dark polymers for industrial sorting technologies, economically profitable recycling of plastics from Waste Electrical and Electronical Equipment (WEEE) can be envisaged even in the presence of residual impurities. In ABS extracted from WEEE, PP is expected to be the more detrimental because of its important lack of compatibility. Hence, PP was incorporated to ABS at different rates (2 to 8 wt%) with a twin-screw extruder. PP was shown to exhibit a nodular morphology with an average diameter around 1-2 µm. Tensile properties were importantly diminished beyond 4 wt% but impact resistance was decreased even at 2 wt%. Both properties were strongly reduced as function of the contamination rate. Various potential compatibilizers for the ABS + 4 wt% PP system were evaluated: PPH-g-MA, PPC-g-MA, ABS-g-MA, TPE-g-MA, SEBS and PP-g-SAN. SEBS was found the most promising, leading to diminution of nodule sizes and also acting as an impact modifier. Finally, a Design Of Experiments using the Response Surface Methodology (DOE-RSM) was applied to visualize the impacts and interactions of extrusion temperature and screw speed on impact resistance of compatibilized and uncompatibilized ABS + 4 wt% PP systems. Resilience improvements were obtained for the uncompatibilized system and interactions between extrusion parameters and compatibilizers were noticed.

Acrylonitrile Butadiene Styrene and Polypropylene Blend with Enhanced Thermal and Mechanical Properties for Fused Filament Fabrication

Acrylonitrile butadiene styrene (ABS) is the oldest fused filament fabrication (FFF) material that shows low stability to thermal aging due to hydrogen abstraction of the butadiene monomer. A novel blend of ABS, polypropylene (PP), and polyethylene graft maleic anhydride (PE-g-MAH) is presented for FFF. ANOVA was used to analyze the effects of three variables (bed temperature, printing temperature, and aging interval) on tensile properties of the specimens made on a custom-built pellet printer. The compression and flexure properties were also investigated for the highest thermal combinations. The blend showed high thermal stability with enhanced strength despite three days of aging, as well as high bed and printing temperatures. Fourier-transform infrared spectroscopy (FTIR) provided significant chemical interactions. Differential scanning calorimetry (DSC) confirmed the thermal stability with enhanced enthalpy of glass transition and melting. Thermogravimetric analysis (TGA) also revealed high temperatures for onset and 50% mass degradation. Signs of chemical grafting and physical interlocking in scanning electron microscopy (SEM) also explained the thermo-mechanical stability of the blend.

Poly(Acrylonitrile-Butadiene-Styrene) as a Special β-Nucleating Agent on the Toughness of Isotactic Polypropylene

The influence of poly(acrylonitrile–butadiene–styrene) (ABS) as a special β-nucleating agent on the impact and tensile properties of isotactic polypropylene (iPP) were investigated by dynamic rheological measurements, wide-angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and mechanical properties tests. It is found that the β nucleation efficiency of ABS is closely related to its concentration, dispersibility, and molding method for the iPP/ABS blends. The content of β-crystal (K_β) rises with the incorporation of ABS and shows a maximum with the introduction of 1% ABS for compression-molded blends and 2% ABS for injection-molded blends, respectively, which is followed by a decrease in K_β. The addition of a small amount of ABS has a significant reinforcing and toughening effect on iPP. Compared with the compression-molded samples, the ABS dispersed phase in injection-molded samples has a smaller particle size and a larger specific surface area, which are favorable for stress transmission and higher β nucleation efficiency, and therefore, better tensile and impact properties can be expected.

Toughening of an epoxy thermoset with poly[styrene-alt-(maleic acid)]-block-polystyrene-block-poly(n-butyl acrylate) reactive core–shell particles

Reactive core–shell particles for epoxy toughening were synthesized via reversible addition–fragmentation chain transfer emulsion polymerization mediated by an amphiphilic macro-RAFT agent followed by core-crosslinking to increase stability.