Phase separation to create hydrophilic yet non-water soluble PLA/PLA-b-PEG fibers via electrospinning

Development of Functionalized Polylactide Thin Films Using Poly(methylhydrogenosiloxane) Sol-Gel Process with Improved Antifouling Properties

Biobased polylactide (PLA) films were modified with low reticulate polysiloxane gel acting as a scalable platform for the hydrophilization of polymeric film surface. The PLA thin film was first coated with poly(methylhydrogenosiloxane) (PMHS) by the sol-gel transition via the condensation of diethoxymethylsilane (DH) and triethoxysilane (TH) using trifluoromethanesulfonic acid as a catalyst. Then, hydrosilylation of Si-H bonds in the presence of Karstedt's catalyst allowed the covalent grafting of hydrophilic alkene-containing molecules, i.e., triethylene glycol monomethyl allyl (TEGMEA) and a new zwitterionic allylcarboxybetaine (ACB) synthesized for the first time by the quaternization of dimethyl allyl amine (DMAA) with β-propiolactone. PMHS coating on the PLA film was evidenced by Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The observation by atomic force microscopy (AFM) revealed a homogeneous coating with low roughness (RMS = 0.29 nm). The hydrophilicity of functionalized PLA films was determined by water contact angle (WCA) measurements using the captive bubble method. A large increase in wettability properties was observed for both grafting with TEGMEA (WCA = 38°) and ACB (WCA = 42°) in comparison with the native PLA film (WCA = 80°). Moreover, the biocompatibility and antifouling efficiency of functionalized PLA films were evaluated by protein adsorption, bacterial adhesion, and cytotoxicity tests. The results indicate that the grafting of the two types of hydrophilic compounds does not affect the biocompatibility of PLA while significantly reducing protein adsorption and bacterial adhesion, thus showing the great potential of this surface functionalization strategy for applications in the medical field.

Increasing Stability of Biotin Functionalized Electrospun Fibers for Biosensor Applications

This paper describes the effects of both solvent and copolymer block lengths on the stability of electrospun poly(lactic acid)/poly(lactic acid)-b-poly(ethylene glycol) (PLA/PLA-b-PEG) and PLA/PLA-b-PEG-Biotin fibers in water. By tailoring the block length of copolymers PLA-b-PEG, water stability of electrospun fibers is improved over fibers reported previously. The solvent used also influenced the stability and hydrophilicity of resulting fibers. Fibers formed using 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP) have greater water stability, but less PEG at the surface of fibers than fibers spun from dimethylformamide (DMF). Attaching biotin to the end of PLA(3600)-b-PEG(2000) and spinning from DMF resulted, initially, in 7.6% of the total biotin incorporated into the fiber, assuming every PEG terminal had one biotin attached (1.1 mg of biotin per gram of fiber) available at the fibers' surface. In addition, PLA/PLA(3600)-b-PEG(2000)-Biotin spun from DMF hindered biotin migration to the aqueous phase, leaving 2% of the incorporated biotin remaining at the surface of fibers after 7 days of water exposure. The water wicking ability of DMF spun fibers also increased significantly with the biotin attachment to the PEG terminal. While HFIP spun fibers lost little biotin from fibers, there was no detectable surface available biotin, indicating biotin was at the interior. With biotin and PEG at the interior of the fibers spun from HFIP, the water wicking remained the same for PLA/PLA(3600)-b-PEG(2000) spun samples and decreased for PLA/PLA(5700)-b-PEG(1000). The dissimilarities observed in water wicking for HFIP spun samples are primarily the result of differences in fiber morphology.

Surface Functional Poly(lactic Acid) Electrospun Nanofibers for Biosensor Applications

In this work, biotin surface functionalized hydrophilic non-water-soluble biocompatible poly(lactic acid) (PLA) nanofibers are created for their potential use as biosensors. Varying concentrations of biotin (up to 18 weight total percent (wt %)) were incorporated into PLA fibers together with poly(lactic acid)-block-poly(ethylene glycol) (PLA-b-PEG) block polymers. While biotin provided surface functionalization, PLA-b-PEG provided hydrophilicity to the final fibers. Morphology and surface-available biotin of the final fibers were studied by Field Emission Scanning Electron Microscopy (FESEM) and competitive colorimetric assays. The incorporation of PLA-b-PEG block copolymers not only decreased fiber diameters but also dramatically increased the amount of biotin available at the fiber surface able to bind avidin. Finally, fiber water stability tests revealed that both biotin and PLA-b-PEG, migrated to the aqueous phase after relatively extended periods of water exposure. The functional hydrophilic nanofiber created in this work shows a potential application as a biosensor for point-of-care diagnostics.