The Effect of Glycol Derivatives on the Properties of Bio-Based Unsaturated Polyesters

The scope of the present study was to prepare fully bio-based unsaturated polyester resins (UPRs) with comparable properties to the commercial formulations. The focus was set on the determination of the optimal prepolymer formulation using the same set of diacids (itaconic and succinic acid) and different diols (propylene glycol, isosorbide and neopentyl glycol) or its equimolar mixtures, keeping the fixed molar ratio of 1:1:2.1 in all feed compositions. Instead of commonly used styrene, bio-based dimethyl itaconate was used as a reactive diluent (RD). The rheology of the obtained resins was studied in detail. The effect of the used diol on structural (FTIR), thermal (DSC), thermomechanical (DMA), and mechanical (tensile) properties was explained. The properties of UPRs were found to be highly dependent on the diol used in the prepolymer formulation. The UPR with an equimolar ratio of propylene glycol and neopentyl glycol was shown to be the most promising candidate to compete with the commercial petroleum-based resins.

The Use of Recycled PET for the Synthesis of New Mechanically Improved PVP Composite Nanofibers

Polyethylene terephthalate (PET) waste has become a major challenge for the conservation of the environment due to difficult degradation. For this reason, it is important to develop new recycling strategies for reusing this waste. In this work, the electrospinning technique was used to synthesize composite nanofibers of polyvinylpyrrolidone (PVP), recycling PET (RPET) that was obtained from the chemical recycling of postconsumer PET with glycolysis and styrene (ST) as a crosslinking agent. The polymer solutions were analyzed by viscosity and frequency sweeping, while the composite nanofibers were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis/differential scanning calorimetry (TGA/DSC), and nanoindentation to compare their properties. The PVP nanofibers presented an average diameter of 257 nm; the RPET/PVP and RPET/PVP/ST composite nanofibers had average diameters of 361 nm and 394 nm, respectively; and the modulus of elasticity and hardness of the RPET/PVP/ST composite nanofibers were 29 and 20 times larger, respectively, than those of the PVP nanofibers. With the synthesis of these composite nanofibers, a new approach to PET recycling is presented.

Alkali Concentration and Diluent Effects on Properties of Grape Cane Fiber-Reinforced Polymer Composites

The main objective of this study was to investigate the properties of polymer composites reinforced with grape cane fibers. The fibers were subjected to a sodium hydroxide (NaOH) treatment at two treatment concentrations to extract the fibers as well as fiber surface treatment. Panels were fabricated by hand lay-up and compression molding according to different fiber types, namely outer bark (OB) and whole (W) fibers. The whole fiber was a mixture of OB and inner bark (IB) fibers. Grape cane fibers were used as the reinforcement material for unsaturated polyester (UPE) resin panels. Acrylated epoxidized soybean oil (AESO) was used as a reactive diluent material with the UPE resin, and the results were compared with panels prepared with commercial styrene-UPE. There were inconsistent alkali treatment concentration effects on the mechanical properties and water absorption. However, panels fabricated with the whole bark fibers that have been treated with 1 wt % NaOH and had AESO-UPE resin resulted in the best tensile and flexural strength.

Optimization of Reactive Diluent for Bio-Based Unsaturated Polyester Resin: A Rheological and Thermomechanical Study

Nowadays, unsaturated polyester resins (UPR) are mainly obtained from non-renewable resources. The ever-increasing regulations and the continuous demand for more sustainability have led to extensive research towards more environmentally suitable alternatives to petroleum-based materials. However, one of the main disadvantages of bio-based UPR is their relatively high viscosity compared to petrochemical ones. In order to overcome this drawback, in this work, we investigated the possibility to lower the resin viscosity utilizing a mixture of dimethyl itaconate (DMI) and methyl methacrylate (MMA) as a reactive diluent. The effect of the DMI and MMA ratio on resin rheological properties was investigated. The optimal curing parameters were determined and all UPRs had a high gel content, which was shown to be dependent on the DMI and MMA ratio in the formulation. Furthermore, thermomechanical and mechanical properties of the resulting network were also found to be affected by the used reactive diluent mixture. A small substitution of DMI by MMA proved to be advantageous since it offers lower resin viscosity and improved mechanical properties.