Inherent porous structure modified by titanium dioxide nanoparticle incorporation and effect on the fouling behavior of hybrid poly(vinylidene fluoride) membranes

Improved Efficiency and Stability of MXene Membranes via Interlayer Space Tuning for Oily Water Separation

Surfactant-stabilized oil-in-water emulsions are a major environmental concern due to their severe consequences for aquatic organisms and humans. Two-dimensional materials, particularly MXenes, are widely used in various applications and could be used in designing advanced membranes. The narrow interlayer spacing and intrinsic oxidation severely limit mass diffusion and induce poor stability, respectively, of MXene-based separating layers on the membrane support, rendering it challenging to use for oil-water separation. Herein, a high-performing, minimally defective MXene membrane with large d-spacing was fabricated. The d-spacing of the MXene sheets was controlled using Si-based species as the intercalating agents. The modified MXene-based membrane (ultrasonication-assisted exfoliated MXene with Si pillars) (U-MX-Si) exhibited an enlarged interlayer spacing of 11 Å, increased surface energy of 41 mJ·m-2, and less defective separating layer compared to that of pristine MXene, which was due to enhanced interlayer spacing. This phenomenon induced a higher degree of exfoliated sheets that facilitated better MXene sheet self-assembly on the membrane support, thereby resulting in high separation efficiency (99%). An increase in the surface energy of the U-MX-Si membrane caused a constant permeate flux during operation, which demonstrated their practical implications. This study presents an important pathway for designing MXene-based membranes for separation applications.

Recent Advances on the Fabrication of Antifouling Phase-Inversion Membranes by Physical Blending Modification Method

Membrane technology is an essential tool for water treatment and biomedical applications. Despite their extensive use in these fields, polymeric-based membranes still face several challenges, including instability, low mechanical strength, and propensity to fouling. The latter point has attracted the attention of numerous teams worldwide developing antifouling materials for membranes and interfaces. A convenient method to prepare antifouling membranes is via physical blending (or simply blending), which is a one-step method that consists of mixing the main matrix polymer and the antifouling material prior to casting and film formation by a phase inversion process. This review focuses on the recent development (past 10 years) of antifouling membranes via this method and uses different phase-inversion processes including liquid-induced phase separation, vapor induced phase separation, and thermally induced phase separation. Antifouling materials used in these recent studies including polymers, metals, ceramics, and carbon-based and porous nanomaterials are also surveyed. Furthermore, the assessment of antifouling properties and performances are extensively summarized. Finally, we conclude this review with a list of technical and scientific challenges that still need to be overcome to improve the functional properties and widen the range of applications of antifouling membranes prepared by blending modification.

Fouling-free ultrafiltration for humic acid removal

Membrane fouling is a serious concern that significantly affects the membrane filtration process. In this study, an ultrafiltration (UF) membrane was developed with surface auto-regeneration potential by immobilizing a photocatalyst [titanium dioxide nanoparticles (TiO₂ NPs)] on a hybrid polyvinylidene fluoride (PVDF) membrane to reduce fouling. The combination of photocatalysis and UF, namely, photocatalytic UF, induced the surface auto-regeneration potential to the membrane. The photocatalytic process was initiated after UV light reached the TiO₂ NPs through a quartz window in the membrane containing cell. The membrane, with an optimized distribution of TiO₂ NPs (3.04 g m⁻²), could completely regenerate itself during photocatalytic UF [with 2 mg L⁻¹ humic acid (HA)] without experiencing membrane fouling during 90 min of filtration. The impact of temperature, an important factor for increasing the kinetic rate of the photocatalyst, was also studied. The results showed that an increase in temperature did not affect the photocatalytic process, but increased the permeate flux, which was attributed to the decrease in kinematic viscosity of the water. Finally, four consecutive photocatalytic UF cycles demonstrated the stability of the membrane for a fouling-free UF process.

Membrane fouling is a serious concern that significantly affects the membrane filtration process.

Improved PVDF membrane performance by doping extracellular polymeric substances of activated sludge

Polyvinylidene fluoride (PVDF) membrane has been widely applied in water and wastewater treatment because of its high mechanical strength, thermal stability and chemical resistance. However, the hydrophobic nature of PVDF membrane makes it readily fouled, substantially reducing water flux and overall membrane rejection ability. In this work, an in-situ blending modifier, i.e., extracellular polymeric substances (EPS) from activated sludge, was used to enhance the anti-fouling ability of PVDF membrane. Results indicate that the pure water flux of the membrane and its anti-fouling performance were substantially improved by blending 8% EPS into the membrane. By introducing EPS, the membrane hydrophilicity was increased and the cross section morphology was changed when it interacted with polyvinl pyrrolidone, resulting in the formation of large cavities below the finger-like pores. In addition, the fraction of pores with a size of 100-500 nm increased, which was also beneficial to improving membrane performance. Surface thermodynamic calculations indicate the EPS-functionalized membrane had a higher cohesion free energy, implying its good pollutant rejection and anti-fouling ability. This work provides a simple, efficient and cost-effective method to improve membrane performance and also extends the applications of EPS.

Developing an antibacterial super-hydrophilic barrier between bacteria and membranes to mitigate the severe impacts of biofouling

Biofouling produces concentrated microbial populations with highly resistive biofilms and is considered to be a serious obstacle for a wide range of membrane technology applications. An antibacterial super-hydrophilic barrier could help to reduce biofouling by preventing direct contact between membranes and bacteria. In this study, an antibacterial super-hydrophilic barrier consisting of a layer of TiO₂ nanoparticles (NPs) was developed on polyvinylidene fluoride (PVDF)-based membrane via a facile technique. The results demonstrated that the presence of TiO₂ NPs eliminated the first step of biofouling, ie bacterial adhesion to the membrane. In addition, after bacterial deposition onto the membrane during ultrafiltration (UF), the TiO₂ NPs significantly retarded bacterial growth and reproduction (the second step of biofouling). During UF, the membrane flux decreased due to bacterial deposition, but 85% of the flux was recovered through physical cleaning using water. This study sheds light on the potential advantages of antibacterial super-hydrophilic membranes for biofouling mitigation.