Design and synthesis of organosoluble and transparent polyimides containing bulky substituents and noncoplanar structures

Synthesis and properties of highly processable asymmetric polyimides with bulky phenoxy groups

A series of new aromatic polyimides (PIs) and co-PIs containing bulky tert-butyl phenoxy group was synthesized by one-step high-temperature polycondensation of 1,3-diamino-4-(4′- tert-butylphenoxy)benzene ( tBuPDAB) with different commercially available aromatic dianhydrides. The polymers were obtained in quantitative yields with inherent viscosities of 0.40–0.70 dL g−1. They exhibited high thermal stability with 10% weight loss above 480°C and were cast in films with good mechanical properties capable to be tested as gas separation membranes. These PIs were compared with analogs bearing phenoxy group (PDAB). The incorporation of tBu improved the solubility of the PIs, their free volume fraction, d-spacing, and gas permeability coefficients in comparison with their analogs obtained from PDAB. The permeability enhancement was from 2.5 to 8 times depended on the gas tested. The PI, based on tBuPDAB and 4,4’-(hexafluoroisopropylidene)diphtalic anhydride and, thus, containing two different bulky pendant groups, showed the highest gas permeability coefficient for CO2 (58.3 Barrer) and moderate ideal selectivity to the gas pair CO2/CH4 ( α = 18.0).

Optical, thermal and gas separation properties of acetate-containing copoly(ether-imide)s based on 6FDA and fluorenyl diamines

The diamine, 9,9-bis[4-(4-amino-3-hydroxylphenoxy)phenyl]fluorene (BAHPPF) was synthesized by the modified two-step method. Then, a series of acetate-containing copoly(ether-imide)s were prepared by the copolymerization of BAHPPF, 9,9-bis(4-aminophenyl)fluorene (BAF) and 2,2′-bis(3,4-dicarboxyphenyl)hexafluoropropane dianhydride (6FDA) followed by chemical imidization. The structures and properties of the BAHPPF and copoly(ether-imide)s were characterized by nuclear magnetic resonance spectrometer (NMR), Fourier transform infrared spectrometer (FTIR), X-ray diffractometer (XRD), differential scanning calorimeter (DSC), thermogravimetric analyzer (TGA), ultraviolet-visible spectrophotometer (UV-VIS), and tensile testing. Single gas permeation performances of these copoly(ether-imide)s were also studied for five representative gases of interest including H2, O2, N2, CO2, and CH4. The experimental results showed that the copoly(ether-imide)s showed excellent optical properties with high light transmittance above 80.2% at 450 nm. The glass transition temperature of these copolymers were higher than 333°C. Their tensile strength and Young’s module also increased, and the elongation decreased with the decrease of BAHPPF. High gas permeabilities of copoly(ether-imide)s were obtained, and the ideal selectivity of CO2/CH4 was improved due to the introduction of acetate group and flexible ether linkage. These copoly(ether-imide)s could be applied to the field of optics and gas separation.

Synthesis and Characterization of Organosoluble, Thermal Stable and Hydrophobic Polyimides Derived from 4-(4-(1-pyrrolidinyl)phenyl)-2,6-bis(4-(4-aminophenoxy)phenyl)pyridine

A novel aromatic diamine monomer, 4-(4-(1-pyrrolidinyl)phenyl)-2,6-bis(4-(4-aminophenoxy)phenyl)pyridine (PPAPP) containing pyridine rings, pyrrolidine groups, and ether linkages, was successfully synthesized using 4-hydroxyacetophenone and 1-chloro-4-nitrobenzene as starting materials by three-step reactions, and then used to synthesize a series of polyimides by polycondensation with various aromatic dianhydrides via a two-step method. The structure of PPAPP was characterized by NMR, FT-IR, and mass spectrometry analysis methods. These polymers showed good solubility in common organic solvents (e.g., NMP, DMF, DMSO, and DMAc) at room temperature or on heating. Moreover, they presented a high thermal stability with the glass transition temperature (Tgs) exceeding 316 °C, as well as the temperature of 10% weight loss ranged from 552⁻580 °C with more than 67% residue at 800 °C under nitrogen. Furthermore, they also exhibited excellent hydrophobicity with a contact angle in the range of 85.6°⁻97.7°, and the results of Wide-Angle X-ray Diffraction (WAXD) indicated that all of the polymers revealed an amorphous structure.