Zwitterionic-polymer-functionalized poly(vinyl alcohol-co-ethylene) nanofiber membrane for resistance to the adsorption of bacteria and protein

Dynamically Cross-Linked Double-Network Hydrogels with Matched Mechanical Properties and Ideal Biocompatibility for Artificial Blood Vessels

Vessel transplantation is currently considered the "gold standard" treatment for cardiovascular disease. However, ideal artificial vascular grafts should possess good biocompatibility and mechanical strength that match those of native autologous vascular tissue to promote in vivo tissue regeneration. In this study, a series of dynamic cross-linking double-network hydrogels and the resultant hydrogel tubes were prepared. The hydrogels (named PCO), composed of rigid poly(vinyl alcohol) (PVA), flexible carboxymethyl chitosan (CMCS), and a cross-linker of aldehyde-based β-cyclodextrin (OCD), were formed in a double-network structure with multiple dynamical cross-linking including dynamic imine bonds, hydrogen bonds, and microcrystalline regions. The PCO hydrogels exhibited superior mechanical strength, good network stability, and fatigue resistance. Additionally, it demonstrated excellent cell and blood compatibility. The results showed that the introduction of CMCS/OCD led to a significant increase in the proliferation rate of endothelial cells seeded on the surface of the hydrogel. The hemolysis rate in the test was lower than 0.3%, and both protein adsorption and platelet adhesion were reduced, indicating an excellent anticoagulant function. The plasma recalcification time test results showed that endogenous coagulation was alleviated to some extent. When formed into blood vessels and incubated with blood, no thrombus formation was observed, and there was minimal red blood cell aggregation. Therefore, this novel hydrogel tube, with excellent mechanical properties, exhibits antiadhesive characteristics toward blood cells and proteins, as well as antithrombotic properties, making it hold tremendous potential for applications in the biomedical and engineering fields.

Ultrasensitive Ratiometric Electrochemiluminescence Sensor with an Efficient Antifouling and Antibacterial Interface of PSBMA@SiO2-MXene for Oxytetracycline Trace Detection in the Marine Environment

The sensitivity and accuracy of electrochemiluminescence (ECL) sensors for detecting small-molecule pollutants in environmental water are affected not only by nonspecific adsorption of proteins and other molecules but also by bacterial interference. Therefore, there is an urgent need to develop an ECL sensor with antifouling and antibacterial functions for water environment monitoring. Herein, a highly efficient antifouling sensing interface (PSBMA@SiO2-MXene) based on zwitterionic sulfobetaine methacrylate (SBMA) antifouling nanospheres (NPs) and two-dimensional MXene nanosheets was designed for the sensitive detection of oxytetracycline (OTC), an antibiotic small-molecule pollutant. Specifically, SBMA with good hydrophilicity and electrical neutrality was connected to SiO2 NPs, thus effectively reducing protein and bacterial adsorption and improving stability. Second, MXene with a high specific surface area was selected as the carrier to load more antifouling NPs, which greatly improves the antifouling performance. Meanwhile, the introduction of MXene also enhances the conductivity of the antifouling interface. In addition, a ratio-based sensing strategy was designed to further improve the detection accuracy and sensitivity of the sensor by utilizing Au@luminol as an internal standard factor. Based on antifouling and antibacterial interfaces, as well as internal standard and ratiometric sensing strategies, the detection range of the proposed sensor was 0.1 ng/mL to 100 μg/mL, with a detection limit of 0.023 ng/mL, achieving trace dynamic monitoring of antibiotics in complex aqueous media.

Enhancing antifouling property of PVA membrane by grafting zwitterionic polymer via SI-ATRP method

Poly(zwitterions) polymer brushes were fabricated by surface-initiated atom transfer radical polymerization (SI-ATRP) on PVA substrate. The results of XPS and FTIR proved the successful graft of CBMA and SBMA to PVA. The surface of the PVA films would be rougher after the functionalization. Its hydrophilicity increased dramatically and the water contact angle decreased from 45.2° to 7.2°. The visible light transmittance was above 88%. Mechanical properties decreased slightly after grafting, the tensile strength and tensile strain at break were in 1.23-1.85 MPa and 361.7-471.1%, respectively. The anti-protein adsorption performance of the modified PVA film was significantly enhanced and the lowest adsorption amount was up to 2.25 μg/cm². The cytotoxicity grade of modified PVA film was 0-1, which indicated the modified film possessed no cytotoxicity. Additionally, the surface of zwitterion-grafted PVA film had strongly resistance to cell adhesion. All the results confirmed that the zwitterions modified PVA was a promising anti-fouling material for the further biomedical use.

Protein Resistant Polymeric Biomaterials

Toward improving implantable medical devices as well as diagnostic performance, the development of polymeric biomaterials having resistance to proteins remains a priority. Herein, we highlight key strategies reported in the recent literature that have relied upon improvement of surface hydrophilicity via direct surface modification methods or with bulk modification using surface modifying additives (SMAs). These approaches have utilized a variety of techniques to incorporate the surface hydrophilization agent, including physisorption, hydrogel network formation, surface grafting, layer-by-layer (LbL) assembly and blending base polymers with SMAs. While poly(ethylene glycol) (PEG) remains the gold standard, new alternatives have emerged such as polyglycidols, poly(2-oxazoline)s (POx), polyzwitterions, and amphiphilic block copolymers. While these new strategies provide encouraging results, the need for improved correlation between in vitro and in vivo protein resistance is critical. This may be achieved by employing complex protein solutions as well as strides to enhance the sensitivity of protein adsorption measurements.

Mechanical and rheological properties of polystyrene-block-polybutadiene-block-polystyrene copolymer reinforced with carbon nanotubes: effect of processing conditions

Styrene-b-butadiene-b-styrene (SBS)-based nanocomposites filled with unmodified and –COOH functionalized carbon nanotubes (CNTs) have been formulated at different processing conditions in order to provide an understanding of the influence of the processing temperature and mixing speed on the nanofillers dispersion and on the overall properties of the nanocomposites. The evaluation of the nanocomposites’ mechanical and rheological behavior reveals that the effect of the processing speed on the final properties is almost negligible. Differently, the processing temperature influences strongly the mechanical and rheological properties of SBS-based nanocomposites. Indeed, for the nanocomposites formulated at high temperatures a significant enhancement of the overall properties with respect to the neat matrix has been achieved. Moreover, morphological analyses show that the state of dispersion of both unmodified and functionalized CNTs progressively improves as the processing temperature increases. Particularly, at low processing temperatures a segregated morphology in which the nanofillers are selectively confined in the domains of the SBS matrix has been obtained, while the nanocomposites formulated at 180°C show a homogeneous and uniform CNTs dispersion throughout the matrix and a strong level of interfacial adhesion between the copolymer chains and the dispersed nanofillers.