Poly(3-hydroxybutyrate)-thermoplastic starch-organoclay bionanocomposites: Surface properties

Development and physiochemical assessment of graphene-bioactive glass-P(3HB-co-4HB) composite scaffold as prospect biomaterial for wound healing

The clinical management of wounds presents a considerable challenge because dressing selection must prioritise the provision of appropriate barrier and the healing properties, consider patient's compliance factors such as comfort, functionality and practicality. This study primarily aimed to develop a composite scaffold patch for potential application in wound healing. Poly(3-hydroxybutyrate-co-4-hydroxybutyrate) [P(3HB-co-4HB)] is a biopolymer that originated from bacteria. It is well-recognised owing to its distinctive mechanical and physical characteristics suitable for biomedical applications. Graphene (G) and bioactive glass (BG) are biocompatible towards humans, and enhanced properties are achievable by adding biopolymer. In this study, composite scaffolds were developed by combining P(3HB-co-4HB) at a distinct proportion of 4HB monomer reinforced with G (3.0 wt.%) and BG (2.5 wt.%) by using solvent casting, resulting in two types of composite scaffolds: P(3HB-co-25%4HB)/G/BG and P(3HB-co-37%4HB)/G/BG. A successful composite scaffold as a unified structure was achieved based on chemical assessments of organic and inorganic elements within the composites. The pure polymer displayed a smooth surface, and the BG and G addition into the composite scaffolds increased surface roughness, forming irregular pores and protuberances. The wettability and hydrophilicity of the composites significantly improved up to 40% in terms of water uptake. An increment in crystallisation temperature diminished the flexibility of the composite's scaffolds. Evaluation of Presto Blue biocompatibility demonstrated nontoxic behaviour with a dosage of less than 25.00 mg ml-1of composite scaffold-conditioned media. The L929 fibroblast cells displayed excellent adhesion to both types of composite scaffolds, as evidenced by the increased percentage of cell viability observed throughout 14 d of exposure. These findings demonstrate the importance of optimising each component within the composite scaffolds and their interrelation, paving the way for excellent material properties and enhancing the potential for wound healing applications.

Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (P(3HB-co-3HV))/Bacterial Cellulose (BC) Biocomposites for Potential Use in Biomedical Applications

The aim of this study was to obtain biocomposites consisting of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), bacterial cellulose (BC) and α-tocopherol by a melt processing technique for potential use in biomedical applications. The melt processing and roughness of biocomposites were evaluated and compared to sample without BC. The degradation rate of PHBV/BC biocomposites was measured in phosphate buffer saline (PBS) by determining the mass variation and evidencing of thermal and structural changes by differential scanning calorimetry (DSC) and attenuated total reflectance-Fourier transformed infrared spectrometry (ATR-FTIR). The cell viability, cell morphology, cell cycle distribution and total collagen content were investigated on murine NCTC fibroblasts. Overall, the adding of BC to polyester matrix led to an adequate melt processing of biocomposites and increased surface roughness and cytocompatibility, allowing the cells to secrete the extracellular matrix (collagen) and stimulate cell proliferation. Results showed that the PHBV/BC biocomposites were favorable for long-term degradation and could be used for the design of medical devices with controlled degradability.

Thermoresponsive Bentonite for Water-Based Drilling Fluids

As an important industrial material, bentonite has been widely applied in water-based drilling fluids to create mud cakes to protect boreholes. However, the common mud cake is porous, and it is difficult to reduce the filtration of a drilling fluid at high temperature. Therefore, this paper endowed bentonite with a thermo response via the insertion of N-isopropylacrylamide (NIPAM) monomers. The interaction between NIPAM monomers and bentonite was investigated via Fourier infrared spectroscopy (FTIR), isothermal adsorption, and X-ray diffraction (XRD) at various temperatures. The results demonstrate that chemical adsorption is involved in the adsorption process of NIPAM monomers on bentonite, and the adsorption of NIPAM monomers accords with the D-R model. With increasing temperature, more adsorption water was squeezed out of the composite when the temperature of the composite exceeded 70 °C. Based on the composite of NIPAM and bentonite, a mud cake was prepared using low-viscosity polyanionic cellulose (Lv-PAC) and initiator potassium peroxydisulfate (KPS). The change in the plugging of the mud cake was investigated via environmental scanning electron microscopy (ESEM), contact angle testing, filtration experiments, and linear expansion of the shale at various temperatures. In the plugging of the mud cake, a self-recovery behavior was observed with increasing temperature, and resistance was observed at 110 °C. The rheology of the drilling fluid was stable in the alterative temperature zone (70-110 °C). Based on the high resistance of the basic drilling fluid, a high-density drilling fluid (ρ = 2.0 g/cm3) was prepared with weighting materials with the objective of drilling high-temperature formations. By using a high-density drilling fluid, the hydration expansion of shale was reduced by half at 110 °C in comparison with common bentonite drilling fluid. In addition, the rheology of the high-density drilling fluid tended to be stable, and a self-recovery behavior was observed.