Polyurethane Wood Adhesives Prepared from Modified Polysaccharides

This study investigated the performance of polyurethane adhesives prepared with various combinations of wheat starch that had been modified by isophorone diisocyanate (MS), two polyol types (1,3-propanediol (PD) and glycerol (Gly)), native wheat starch (NS), and 4,4′-diphenylmethane diisocyanate (pMDI) at a NCO:OH weight ratio of 1:1. Two more adhesives were also synthesized with NS, PD, or Gly and pMDI blends and served as controls. The thermal behavior of the adhesives before and after the curing process, as well as their rheological performance and lap shear strength, were analyzed. Differential scanning calorimetry (DSC) showed a reduction in curing temperature and heat by adding MS. The thermal stability of the cured adhesives was slightly increased by MS addition. The viscosity of the adhesives that contained MS substantially increased at a linear ascendant ramp of shear, while the controls exhibited relatively low viscosity during the whole shear rate spectrum from 0.1 to 100 s⁻¹. The tensile shear strength of wood veneers was also significantly increased by the incorporation of MS under both dry and wet measuring conditions. The maximum dry shear strength was obtained for the adhesive with Gly polyol and a higher content of MS and was comparable to the control adhesive with pMDI.

Characterization of Archaeological European White Elm (Ulmus laevis P.) and Black Poplar (Populus nigra L.)

The present study aims at characterization of freshly-cut and archaeological European white elm and poplar. The archaeological elm sample was buried at a depth of 8–10 m inside of soil with age approximation of ~1800–2000 years old, and the archaeological poplar sample was a part of a boat in a freshwater lake or river with age estimation of ~1000–1200 years. Alteration in the chemical structure of the elm and poplar samples due to the ageing process were confirmed by X-ray photoelectron spectroscopy (XPS). Both archaeological wood (AW) samples illustrated considerably lower cellulose crystallinity than the fresh samples as determined by X-ray diffraction. The sorption behavior of AW and fresh wood (FW) samples were evaluated by means of dynamic vapor sorption (DVS) analysis. Results exhibited a higher equilibrium moisture content (EMC) and sorption hysteresis values in archaeological elm and poplar as compared with the fresh samples. Higher hydrophilicity of the AW samples than the FW ones is attributed to their higher amorphous structure. The extensive degradation of AW samples were also confirmed by scanning electron microscopy (SEM) micrographs.

A Review of Wood Biomass-Based Fatty Acids and Rosin Acids Use in Polymeric Materials

In recent decades, vegetable oils as a potential replacement for petrochemical materials have been extensively studied. Tall oil (crude tall oil, distilled tall oil, tall oil fatty acids, and rosin acids) is a good source to be turned into polymeric materials. Unlike vegetable oils, tall oil is considered as lignocellulosic plant biomass waste and is considered to be the second-generation raw material, thus it is not competing with the food and feed chain. The main purpose of this review article is to identify in what kind of polymeric materials wood biomass-based fatty acids and rosin acids have been applied and their impact on the properties.

Hydrophobic Formulations Based on Tall Oil Distillation Products for High-Density Fiberboards

This study investigates the effect of renewable formulations based on tall oil bio-refinery products on the water vapor sorption and interfiber strength of cellulosic fibers as well as on the properties of high-density fiberboard (HDF) panels. The results obtained for HDF prepared using renewable formulations were compared to the results for HDF obtained using conventional synthetic paraffin wax (hydrowax), which is the hydrophobic agent currently utilized by the industry. Four tall oil distillation products (TODPs) with different levels of fatty and rosin acids were used for preparing the hydrophobic formulations with furfuryl alcohol as an organic solvent. According to determinations with an automated vapor sorption apparatus, the formulations had a similar effect with hydrowax on the sorption behavior of natural fibers. Unlike to hydrowax treatment, the ultimate tensile strength of cellulosic paper-sheets treated with the formulations remained unchanged or significantly increased. At the standard addition load of 1% (wt/wt dry fibers) of the formulations, HDF panels showed comparable and only in one case, e.g., TODP3-based formulation, slightly higher thickness swelling (24 h) than those with hydrowax. The best performing formulation (TODP2-based) in terms of tensile strength of paper sheets did not significantly change the mechanical properties of HDF panels in both standard climate and high humid conditions. Promising results at the standard and humid climate conditions were obtained for HDF panels manufactured with higher TODP2-based formulation amounts (3–5%) and reduced melamine-urea-formaldehyde resin content (10–12% instead of 14%, wt dry resin/wt dry fibers).

Utilization of Partially Liquefied Bark for Production of Particleboards

Bark as a sawmilling residue can be used for producing value-added chemicals and materials. This study investigated the use of partially liquefied bark (PLB) for producing particleboard with or without synthetic adhesives. Maritime pine (Pinus pinaster Ait.) bark was partially liquefied in the presence of ethylene glycol and sulfuric acid. Four types of particleboard panels were prepared with a PLB content of 4.7%, 9.1%, 20%, and 33.3%, respectively. Another five types of particleboard panels were manufactured by using similar amounts of PLB and 10 wt.% of melamine–urea–formaldehyde (MUF) adhesives. Characterization of bark and solid residues of PLB was performed by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and automated vapor sorption (AVS). Mechanical and physical properties of the particleboard were tested according to the European standards EN 310 for determining modulus of elasticity and bending strength, EN 317 for determining thickness swelling after immersion in water, and EN 319 for determining internal bond strength. The results showed that the increase in PLB content improved the mechanical strength for the non-MUF boards, and the MUF-bonded boards with up to 20% of PLB met the requirements for interior uses in dry conditions according to EN 312. The non-MUF boards containing 33.3% of PLB and the MUF-bonded boards showed comparable thickness swelling and water absorption levels compared to the reference board.

Ammonium Lignosulfonate Adhesives for Particleboards with pMDI and Furfuryl Alcohol as Crosslinkers

Tightening formaldehyde emission limits and the need for more sustainable materials have boosted research towards alternatives to urea-formaldehyde adhesives for wood-based panels. Lignin residues from biorefineries consist of a growing raw material source but lack reactivity. Two crosslinkers were tested for ammonium lignosulfonate (ALS)-bio-based furfuryl alcohol (FOH) and synthetic polymeric 4,4'-diphenylmethane diisocyanate (pMDI). The addition of mimosa tannin to ALS before crosslinking was also evaluated. The derived ALS adhesives were used for gluing 2-layered veneer samples and particleboards. Differential Scanning Calorimetry showed a reduction of curing temperature and heat for the samples with crosslinkers. Light microscopy showed that the FOH crosslinked samples had thicker bondlines and higher penetration, which occurred mainly through vessels. Tensile shear strength values of 2-layered veneer samples glued with crosslinked ALS adhesives were at the same level as the melamine reinforced urea-formaldehyde (UmF) reference. For particleboards, the FOH crosslinked samples showed a significant decrease in mechanical properties (internal bond (IB), modulus of elasticity (MOE), modulus of rupture (MOR)) and thickness swelling. For pMDI crosslinked samples, these properties increased compared to the UmF. Although the FOH crosslinked ALS samples can be classified as non-added-formaldehyde adhesives, their emissions were higher than what can be expected to be sourced from the particles.