Magnesium Tetra(phenylethynyl)porphyrin: Stepwise Synthetic Route, Crystal Structures, and Longer Singlet Excited-State Lifetime than Zinc Congener

Chlorophyll-Inspired Magnesium Porphyrin Array Membrane for Vis-Light-Enhanced Osmotic Energy Conversion

Osmotic energy, a renewable clean energy, can be directly converted into electricity through ion-selective membranes. Inspired by the magnesium porphyrin (MgP) in plant chlorophyll, which absorbs vis-light and promotes photoelectric conversion, we demonstrate a MgP array membrane, realizing vis-light-enhanced ion transport regulation ability and osmotic energy conversion. The MgP arrays are self-assembled by a MgP-cored block copolymer under the coordination effect of block copolymer self-assembly and MgP π-π stacking, providing chloride-selective transport channels. Due to the unique photochemical properties of MgP, the chloride ion transport conductance and selectivity can be simultaneously increased under visible-light irradiation, benefiting the osmotic energy conversion. Specifically, the maximum power density increases from 26.7 to 34.5 W·m-2 after visible-light illumination, representing approximately a 30% increase. The construction of MgP arrays realizes photofacilitated osmotic energy conversion, providing an idea for designing an efficient photoelectric conversion system.

A unified evaluation descriptor for π-bridges applied to metalloporphyrin derivatives

Establishing the structure of porphyrins with a A-π-D-π-A configuration is one of the effective strategies to maintain their dominance and compensate shortcomings through flexible changes in fragments. In this regard, π-bridges have attracted wide attention as a parameter affecting molecular backbones, electron transfer, energy levels, absorption, and other properties. However, the essence and influence of π-bridges have not yet been confirmed. In order to satisfy the requirements of intelligent application in molecular design, this study aimed to investigate the control effect of differences in π-bridge composition (thiophene and selenophene) and connection type (single bonds, ethylenic bonds and fused) on photoelectric performance. Y6 and PC61BM were used as acceptors to build donor/acceptor (D/A) interfaces and characterize the film morphology in three dimensions. Results showed that the essence of π-bridges involves a strong bridging effect (adjusting ability) between A and D fragments rather than highlighting its own nature. The large value could obtain high open circuit voltages (VOC), large separation and small recombination rates as well as stable and tight morphology. Therefore, adjusting ability is a unified descriptor for evaluating π-bridges, and it is an effective strategy to adjust material properties and morphology. This insight and discovery may provide a new evaluation descriptor for the screening and design of π-bridges.

A Blueprint for the Stabilization of Sub-Valent Alkaline Earth Complexes

The study of sub-valent Group 2 chemistry is a relatively new research field, being established in 2007 with the report of the first Mg(I) dimers. These species are stabilized by the formation of a Mg-Mg covalent bond; however, the extension of this chemistry to heavier alkaline earth (AE) metals has been frustrated by significant synthetic challenges, primarily associated with the instability of heavy AE-AE interactions. Here we present a new blueprint for the stabilization of heavy AE(I) complexes, based upon the reduction of AE(II) precursors with planar coordination geometries. We report the synthesis and structural characterisation of homoleptic trigonal planar AE(II) complexes of the monodentate amides {N(SiMe3 )2 }- and {N(Mes)(SiMe3 )}- . DFT calculations showed that the LUMOs of these complexes all show some d-character for AE = Ca-Ba. DFT analysis of the square planar Sr(II) complex [Sr{N(SiMe3 )2 }(dioxane)2 ]∞ revealed analogous frontier orbital d-character. AE(I) complexes that could be accessed by reduction of these AE(II) precursors were modelled computationally, revealing exergonic formation in all cases. Crucially, NBO calculations show that some d-character is preserved in the SOMO of theoretical AE(I) products upon reduction, showing that d-orbitals could play a crucial role in achieving stable heavy AE(I) complexes.

Magnesium diethynylporphyrin derivatives with strong near-infrared absorption for solution-process bulk heterojunction organic solar cells

Magnesium diethynylporphyrin derivatives with strong near-infrared absorption were obtained. These derivatives possess electron rich units directly introduced to the porphyrin core. The electron rich units caused strong absorption on the near-infrared region due to an intramolecular charge transfer. Theoretical calculation also proved that the derivatives showed large oscillator strength at the Q band. As a donor material, such large absorption coefficient in the range of long wavelength region is a desirable characteristic for organic solar cells. Organic photovoltaic devices using these diethynylporphyrin derivatives gave a PCE of 2.91% in optimal conditions.

Recent progress in porphyrin- and phthalocyanine-containing perovskite solar cells

In this review, we summarize the application of porphyrins and phthalocyanines in perovskite solar cells to date. Since the first porphyrin- and phthalocyanine-based perovskite solar cells were reported in 2009, their power conversion efficiency has dramatically increased from 3.9% to over 20%. Porphyrins and phthalocyanines have mostly been used as the charge selective layers in these cells. In some cases, they have been used inside the perovskite photoactive layer to form two-dimensional perovskite structures. In other cases, they were used at the interface to engineer the surface energy level. This review gives a chronological introduction to the application of porphyrins and phthalocyanines for perovskite solar cells depending on their role. This review article also provides the history of porphyrin and phthalocyanine derivative development from the perspective of perovskite solar cell applications.

High-yielding Pd2(dba)3·C6H6-based four-fold Sonogashira coupling with selenophene-conjugated magnesium tetraethynylporphyrin for organic solar cells

A catalytic system using Pd2(dba)3·(C6H6)/PPh3/CuI for Sonogashira coupling was demonstrated to synthesize a selenophene-conjugated magnesium tetraethynylporphyrin Mg-TEP-(Se-DPP)4 (2a). The catalytic system enabled four-fold cross-coupling of the four terminal alkynes of magnesium tetraethynylporphyrin with bromoselenophene-tethered diketopyrrolopyrroles (DPPs) to produce the desired star-shaped 2a in 80% yield. This molecule shows higher solubility in organic solvents, more efficient visible and near-infrared region absorption, and a narrower band gap compared with reference thiophene-conjugated congeners. Two strategies, namely, selenium substitution and end-capping, were investigated to optimize bulk heterojunction structures in the active layers of organic solar cells. The optimized device based on 2a:PC61BM exhibited the highest PCE of 6.09% among the tested devices after solvent vapor annealing, owing to efficient exciton dissociation, balanced carrier mobility, and suppressed carrier recombination in the film's ordered morphology.

Origin of Panchromaticity in Multichromophore-Tetrapyrrole Arrays

Panchromatic absorbers that have robust photophysical properties enable new designs for molecular-based light-harvesting systems. Herein, we report experimental and theoretical studies of the spectral, redox, and excited-state properties of a series of perylene-monoimide-ethyne-porphyrin arrays wherein the number of perylene-monoimide units is stepped from one to four. In the arrays, a profound shift of absorption intensity from the strong violet-blue (B _y and B _x) bands of typical porphyrins into the green, red, and near-infrared (Q _x and Q _y) regions stems from mixing of chromophore and tetrapyrrole molecular orbitals (MOs), which gives multiplets of MOs having electron density spread over the entire array. This reduces the extensive mixing between porphyrin excited-state configurations and the transition-dipole addition and subtraction that normally leads to intense B and weak Q bands. Reduced configurational mixing derives from moderate effects of the ethyne and perylene on the MO energies and a more substantial effect of electron-density delocalization to reduce the configuration-interaction energy. Quantitative oscillator-strength analysis shows that porphyrin intensity is also shifted into the perylene-like green-region absorption and that the ethyne linkers lend absorption intensity. The reduced porphyrin configurational mixing also endows the S₁ state with bacteriochlorin-like properties, including a 1-5 ns lifetime.