Kinetic and mechanistic study of CO oxidation over nanocomposite Cu−Fe−Al oxide catalysts

Bimetal doped Cu-Fe-ZIF-8/g-C3N4 nanocomposites for the adsorption of tetracycline hydrochloride from water

Bimetal doped Cu-Fe-zeolitic imidazole framework-8 (ZIF-8)/graphitic carbon nitride (GCN) (Cu-Fe-ZIF-8/GCN) nanocomposites were prepared via one-pot and ion-exchange methods. The main influencing factors, such as adsorbent concentration, TC concentration, initial pH, and coexisting ions, were evaluated in detail. Due to the suitable pore structures and the presence of multiple interactions on the surface, the nanocomposite showed a high adsorption capacity up to 932 mg g-1 for tetracycline hydrochloride (TC), outperforming ZIF-8 by 4.8 times. The adsorption kinetics and adsorption isotherm were depicted in good detail using pseudo-second-order kinetic and Langmuir models, respectively. Thermodynamic calculation revealed that the adsorption of the nanocomposite under experimental conditions was a spontaneous heat absorption process, and was primarily driven by chemisorption. After four cycles of use, the nanocomposite retained 87.2% of its initial adsorption capacity, confirming its high reusability and broad application prospects in removing tetracycline-type pollutants from wastewater.

CO Oxidation over Alumina-Supported Copper Catalysts

CO oxidation, one of the most important chemical reactions, has been commonly studied in both academia and the industry. It is one good probe reaction in the fields of surface science and heterogeneous catalysis, by which we can gain a better understanding and knowledge of the reaction mechanism. Herein, we studied the oxidation state of the Cu species to seek insight into the role of the copper species in the reaction activity. The catalysts were characterized by XRD, N2 adsorption-desorption, X-ray absorption spectroscopy, and temperature-programmed reduction. The obtained results suggested that adding of Fe into the Cu/Al2O3 catalyst can greatly shift the light-off curve of the CO conversion to a much lower temperature, which means the activity was significantly improved by the Fe promoter. From the transient and temperature-programmed reduction experiments, we conclude that oxygen vacancy plays an important role in influencing CO oxidation activity. Adding Fe into the Cu/Al2O3 catalyst can remove part of the oxygen from the Cu species and form more oxygen vacancy. These oxygen vacancy sites are the main active sites for CO oxidation reaction and follow a Mars-van Krevelen-type reaction mechanism.

Synthesis of Self-Supported Cu/Cu3P Nanoarrays as an Efficient Electrocatalyst for the Hydrogen Evolution Reaction

Owing to the energy crisis and environmental pollution, it is essential to develop cheap, environmentally friendly and sustainable energy to replace noble metal electrocatalysts for use in the hydrogen evolution reaction (HER). We report herein that a Cu/Cu3P nanoarray catalyst was directly grown on the surfaces of Cu nanosheets from its Cu/CuO nanoarray precursor by a low-temperature phosphidation process. In particular, the effects of phosphating distance, mass ratio and temperature on the morphology of Cu/Cu3P nanoarrays were studied in detail. This nanoarray, as an electrocatalyst, displays excellent catalytic performance and long-term stability in an acid solution for electrochemical hydrogen generation. Specifically, the Cu/Cu3P nanoarray-270 exhibits a low onset overpotential (96 mV) and a small Tafel slope (131 mV dec−1).

Broadening the Action Spectrum of TiO2-Based Photocatalysts to Visible Region by Substituting Platinum with Copper

In this study, TiO₂-based photocatalysts modified with Pt and Cu/CuO_x were synthesized and studied in the photocatalytic reduction of CO₂. The morphology and chemical states of synthesized photocatalysts were studied using UV-Vis diffuse reflectance spectroscopy, high-resolution transmission electron microscopy, and X-ray photoelectron spectroscopy. A series of light-emitting diodes (LEDs) with maximum intensity in the range of 365–450 nm was used to determine the action spectrum of photocatalysts. It is shown for, the first time, that the pre-calcination of TiO₂ at 700 °C and the use of Cu/CuO_x instead of Pt allow one to design a highly efficient photocatalyst for CO₂ transformation shifting the working range to the visible light (425 nm). Cu/CuO_x/TiO₂ (calcined at 700 °C) shows a rate of CH₄ formation of 1.2 ± 0.1 µmol h⁻¹ g⁻¹ and an overall CO₂ reduction rate of 11 ± 1 µmol h⁻¹ g⁻¹ (at 425 nm).

Atomic Structure of Pd-, Pt-, and PdPt-Based Catalysts of Total Oxidation of Methane: In Situ EXAFS Study

In this study, 3%Pd/Al2O3, 3%Pt/Al2O3 and bimetallic (1%Pd + 2%Pt)/Al2O3 catalysts were examined in the total oxidation of methane in a temperature range of 150–400 °C. The evolution of the active component under the reaction conditions was studied by transmission electron microscopy and in situ extended X-ray absorption fine structure (EXAFS) spectroscopy. It was found that the platinum and bimetallic palladium-platinum catalysts are more stable against sintering than the palladium catalysts. For all the catalysts, the active component forms a “core-shell” structure in which the metallic core is covered by an oxide shell. The “core-shell” structure for the platinum and bimetallic palladium-platinum catalysts is stable in the temperature range of 150–400 °C. However, in the case of the palladium catalysts the metallic core undergoes the reversible oxidation at temperatures above 300 °C and reduced to the metallic state with the decrease in the reaction temperature. The scheme of the active component evolution during the oxidation of methane is proposed and discussed.

Ni-Cu High-Loaded Sol-Gel Catalysts for Dehydrogenation of Liquid Organic Hydrides: Insights into Structural Features and Relationship with Catalytic Activity

The heightened interest in liquid organic hydrogen carriers encourages the development of catalysts suitable for multicycle use. To ensure high catalytic activity and selectivity, the structure-reactivity relationship must be extensively investigated. In this study, high-loaded Ni-Cu catalysts were considered for the dehydrogenation of methylcyclohexane. The highest conversion of 85% and toluene selectivity of 70% were achieved at 325 °C in a fixed-bed reactor using a catalyst with a Cu/Ni atomic ratio of 0.23. To shed light on the relationship between the structural features and catalytic performance, the catalysts were thoroughly studied using a wide range of advanced physicochemical tools. The activity and selectivity of the proposed catalysts are related to the uniformity of Cu distribution and its interaction with Ni via the formation of metallic solid solutions. The method of introduction of copper in the catalyst plays a crucial role in the effectiveness of the interaction between the two metals.