A Rechargeable Aqueous Sodium‐Ion Battery

Graphyne-based 3D porous structure and its sandwich-type graphene structure for alkali metal ion battery anode materials

In order to develop candidate materials for more metal ion battery anodes, a three-dimensional (3D) porous structure 3D-PGY was designed based on graphyne, and a sandwich structure graphene/PGY/graphene (G/PGY/G) was constructed by adjusting the distance between two layers of graphene with 3D-PGY as the middle layer. Systematic calculations have shown that 3D-PGY is thermally and mechanically stable even at temperatures up to 1000 K. Li can migrate in multiple diffusion directions in two structures because of its smaller radius while Na and K ions can only migrate through the larger pores. The energy barriers of Li, Na and K ions in 3D-PGY are 0.18, 0.43 and 0.27 eV respectively. After forming the sandwich structure with graphene, the minimum energy barriers of Li, Na and K ions are decreased to 0.12, 0.37 and 0.24 eV, respectively. As the anode for Li, Na, and K ion batteries, the theoretical specific capacities of 3D-PGY are about 558 mA h g-1, and the average open circuit voltages of 3D-PGY and G/PGY/G are about 0.48/0.52/0.29 and 1.08/1.04/1.39 V, respectively. Finally, using ab initio molecular dynamics simulations, the diffusion coefficients for 3D-PGY at different temperatures, as well as for G/PGY/G at 400 K were obtained. The Li, Na and K ions in both structures can diffuse rapidly and have good rate capabilities. These excellent performances show that the graphyne-based 3D porous structure and its sandwich-type graphene structure are very promising for the development of new battery materials.

In Situ Growth of Sodium Manganese Hexacyanoferrate on Carbon Nanotubes for High-Performance Sodium-Ion Batteries

Sodium manganese hexacyanoferrate (NaMnHCF) has emerged as a research hotspot among Prussian blue analogs for sodium-ion battery cathode materials due to its advantages of high voltage, high specific capacity, and abundant raw materials. However, its practical application is limited by its poor electronic conductivity. In this study, we aim to solve this problem through the in situ growth of NaMnHCF on carbon nanotubes (CNTs) using a simple coprecipitation method. The results show that the overall electronic conductivity of NaMnHCF is significantly improved after the introduction of CNTs. The NaMnHCF@10%CNT sample presents a specific capacity of 90 mA h g-1, even at a current density of 20 C (2400 mA g-1). The study shows that the optimized composite exhibits a superior electrochemical performance at different mass loadings (from low to high), which is attributed to the enhanced electron transport and shortened electron pathway. Surprisingly, the cycling performance of the composites was also improved, resulting from decreased polarization and the subsequent reduction in the side reactions at the cathode/electrolyte interface. Furthermore, we revealed the evolution of potential plateau roots from the extraction of crystal water during the charge-discharge process of NaMnHCF based on the experimental results. This study is instructive not only for the practical application of NaMnHCF materials but also for advancing our scientific understanding of the behavior of crystal water during the charge-discharge process.

An Overview on Anodes for Magnesium Batteries: Challenges towards a Promising Storage Solution for Renewables

Magnesium-based batteries represent one of the successfully emerging electrochemical energy storage chemistries, mainly due to the high theoretical volumetric capacity of metallic magnesium (i.e., 3833 mAh cm-3 vs. 2046 mAh cm-3 for lithium), its low reduction potential (-2.37 V vs. SHE), abundance in the Earth's crust (104 times higher than that of lithium) and dendrite-free behaviour when used as an anode during cycling. However, Mg deposition and dissolution processes in polar organic electrolytes lead to the formation of a passivation film bearing an insulating effect towards Mg2+ ions. Several strategies to overcome this drawback have been recently proposed, keeping as a main goal that of reducing the formation of such passivation layers and improving the magnesium-related kinetics. This manuscript offers a literature analysis on this topic, starting with a rapid overview on magnesium batteries as a feasible strategy for storing electricity coming from renewables, and then addressing the most relevant outcomes in the field of anodic materials (i.e., metallic magnesium, bismuth-, titanium- and tin-based electrodes, biphasic alloys, nanostructured metal oxides, boron clusters, graphene-based electrodes, etc.).