Total ankle replacement along with subtalar joint arthrodesis: In-vitro and in-silico biomechanical investigations

Preoperative incongruent subtalar joint predicts less favorable clinical outcome in total ankle arthroplasty

BACKGROUND

This study aimed to determine the clinical effect of incongruent subtalar joint space on total ankle arthroplasty (TAA).

METHODS

Thirty-four consecutive patients who underwent TAA were grouped according to the status of subtalar joint incongruency. A comparison of clinical and radiographic parameters between groups as well as multiple regression analysis was performed to identify contributing factors to the final functional outcome.

RESULTS

The final American Orthopaedic Foot and Ankle Society (AOFAS) score was significantly higher in the congruent group compared to that of the incongruent group (p = 0.007). There were no significant differences between the two groups in measured radiographic angles. In multiple regression analysis, the female sex (p = 0.006) and incongruency of the subtalar joint (p = 0.013) were found to be significant contributing factors to the final AOFAS score.

CONCLUSIONS

A thorough preoperative investigation should be taken into the state of the subtalar joint for TAA.

Transdermal delivery of celecoxib and α-linolenic acid from microemulsion-incorporated dissolving microneedles for enhanced osteoarthritis therapy

Dissolving microneedles, the promising vehicles for transdermal delivery, are incapable of directly loading hydrophobic components that limit the application of transdermal drug delivery. Microemulsion holds great potential in the solubilisation of water-insoluble drugs but is limited by the high epidermal retention. In this study, we fabricated microemulsion-incorporated dissolving microneedles co-loading celecoxib and α-linolenic acid (Cel-MEs@MNs) for enhancing osteoarthritis (OA) therapy via synergistic anti-inflammation and potent transdermal delivery. Cel-MEs@MNs composed of celecoxib & α-linolenic acid-coloaded microemulsion (Cel-MEs) and hyaluronic acid-based microneedles (MNs) can be completely dissolved in 90 s with a particle size of ∼30 nm. Each microneedle array with a hardness exceeding 30 N contained 57.9 ± 2.5 μg of celecoxib and 442.5 ± 24.2 μg of α-linolenic acid. The 8 h-cumulative transdermal of celecoxib from Cel-MEs@MNs was 89.2 ± 5.1 μg celecoxib/cm², which is 2.98-fold higher than that from Cel-MEs. Combinational celecoxib and α-linolenic acid with a weight ratio of 1/5 can synergistically induce M1-like macrophage to M2 repolarization, reduce M1-like macrophages-resulted chondrocytes apoptosis, and lower serum prostaglandin E-2 (PGE-2). Notably, Cel-MEs@MNs amplified such collaborated anti-inflammatory effects. More importantly, in the treatment of OA-bearing rat models, Cel-MEs@MNs with a half-dose of celecoxib and α-linolenic acid significantly shrunk the paw swelling, reduced inflammatory cytokines, and improved cartilage damage compared with the oral administration of celecoxib and α-linolenic acid, as well as transdermal administration of Cel-MEs. Such an integrational strategy of microemulsion-incorporated dissolving MNs offers the feasibility of combinational celecoxib and α-linolenic acid in transdermal permeation and boosted OA therapy.

Cadaveric Gait Simulation of the Effect of Subtalar Arthrodesis on Total Ankle Replacement Kinematics

BACKGROUND

Patients undergoing total ankle replacement (TAR) often have symptomatic adjacent joint arthritis and deformity. Subtalar arthrodesis can effectively address a degenerative and/or malaligned hindfoot, but there is concern that it places abnormal stresses on the TAR and adjacent joints of the foot, potentially leading to early TAR failure. This study hypothesized that ankle and talonavicular joint kinematics would be altered after subtalar arthrodesis in the setting of TAR.

METHODS

Thirteen mid-tibia cadaveric specimens with neutral alignment were tested in a robotic gait simulator. To simulate gait, each specimen was secured to a static mounting fixture about a 6-degree of freedom robotic platform, and a force plate moves relative to the stationary specimen based on standardized gait parameters. Specimens were tested sequentially in TAR and TAR with subtalar arthrodesis (TAR-ST_fuse). Kinematics and range of motion of the ankle and talonavicular joint were compared between TAR and TAR-ST_fuse.

RESULTS

There were significant differences in kinematics and range of motion between TAR and TAR-ST_fuse groups. At the ankle joint, TAR-ST_fuse had less internal rotation in early-mid stance (P < .05), with decreased range of motion in the sagittal (-2.7 degrees, P = .008) and axial (-1.8 degrees, P = .002) planes in early stance, and increased range of motion in the coronal plane in middle (+1.2 degrees, P < .001) and late (+2.5 degrees, P = .012) stance. At the talonavicular joint, there were significant differences in axial and coronal kinematics in early and late stance (P < .05). Subtalar arthrodesis resulted in significantly decreased talonavicular range of motion in all planes in early and late stance (P < .003).

CONCLUSION

In ankles implanted with the TAR design used in this study, kinematics of the ankle and talonavicular joint were found to be altered after subtalar arthrodesis. Aberrant motion may reflect altered contact mechanics at the prosthesis and increased stress at the bone-implant interface, and affect the progression of adjacent joint arthritis in the talonavicular joint.

CLINICAL RELEVANCE

These findings may provide a correlate to clinical studies that have cited hindfoot arthrodesis as a risk factor for TAR failure.

Finite element stress analysis of the bearing component and bone resected surfaces for total ankle replacement with different implant material combinations

Background

A proper combination of implant materials for Total Ankle Replacement (TAR) may reduce stress at the bearing component and the resected surfaces of the tibia and talus, thus avoiding implant failure of the bearing component or aseptic loosening at the bone-implant interface.

Methods

A comprehensive finite element foot model implanted with the INBONE II implant system was created and the loading at the second peak of ground reaction force was simulated. Twelve material combinations including four materials for tibial and talar components (Ceramic, CoCrMo, Ti6Al4V, CFR-PEEK) and three materials for bearing components (CFR-PEEK, PEEK, and UHMWPE) were analyzed. Von Mises stress at the top and articular surfaces of the bearing component and the resected surfaces of the tibia and talus were recorded.

Results

The stress at both the top and articular surfaces of the bearing component could be greatly reduced with more compliant bearing materials (44.76 to 72.77% difference of peak stress value), and to a lesser extent with more compliant materials for the tibial and talar components (0.94 to 28.09% difference of peak stress value). Peak stresses at both the tibial and talar bone-implant interface could be reduced more strongly by using tibial and talar component materials with smaller material stiffness (7.31 to 66.95% difference of peak stress value) compared with bearing materials with smaller material stiffness (1.11 to 24.77% difference of peak stress value).

Conclusions

Implant components with smaller material stiffness provided a stress reduction at the bearing component and resected surfaces of the tibia and talus. The selection of CFR-PEEK as the material of tibial and talar components and UHMWPE as the material of the bearing component seemed to be a promising material combination for TAR implants. Wear testing and long-term failure analysis of TAR implants with these materials should be included in future studies.

Supplementary Information

The online version contains supplementary material available at 10.1186/s12891-021-04982-3.