1
|
Yoon SE, Kim Y, Kim H, Kwon HG, Kim U, Lee SY, Park JH, Seo H, Kwak SK, Kim SW, Kim JH. Remarkable Electrical Conductivity Increase and Pure Metallic Properties from Semiconducting Colloidal Nanocrystals by Cation Exchange for Solution-Processable Optoelectronic Applications. SMALL (WEINHEIM AN DER BERGSTRASSE, GERMANY) 2023; 19:e2207511. [PMID: 36916693 DOI: 10.1002/smll.202207511] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 12/02/2022] [Revised: 02/16/2023] [Indexed: 06/08/2023]
Abstract
The authors report a strategic approach to achieve metallic properties from semiconducting CuFeS colloidal nanocrystal (NC) solids through cation exchange method. An unprecedentedly high electrical conductivity is realized by the efficient generation of charge carriers onto a semiconducting CuS NC template via minimal Fe exchange. An electrical conductivity exceeding 10 500 S cm-1 (13 400 S cm-1 at 2 K) and a sheet resistance of 17 Ω/sq at room temperature, which are among the highest values for solution-processable semiconducting NCs, are achieved successfully from bornite-phase CuFeS NC films possessing 10% Fe atom. The temperature dependence of the corresponding films exhibits pure metallic characteristics. Highly conducting NCs are demonstrated for a thermoelectric layer exhibiting a high power factor over 1.2 mW m-1 K-2 at room temperature, electrical wires for switching on light emitting diods (LEDs), and source-drain electrodes for p- and n-type organic field-effect transistors. Ambient stability, eco-friendly composition, and solution-processability further validate their sustainable and practical applicability. The present study provides a simple but very effective method for significantly increasing charge carrier concentrations in semiconducting colloidal NCs to achieve metallic properties, which is applicable to various optoelectronic devices.
Collapse
Affiliation(s)
- Sang Eun Yoon
- Department of Molecular Science and Technology, Ajou University, Suwon, 16499, South Korea
| | - Yongjin Kim
- Department of Molecular Science and Technology, Ajou University, Suwon, 16499, South Korea
| | - Hyeongjun Kim
- Department of Energy Engineering, School of Energy and Chemical Engineering, Ulsan National Institute of Science and Technology (UNIST), Ulsan, 44919, South Korea
| | - Hyo-Geun Kwon
- Department of Molecular Science and Technology, Ajou University, Suwon, 16499, South Korea
| | - Unjeong Kim
- Department of Materials Science and Engineering, Department of Energy Systems Research, Ajou University, Suwon, 16499, South Korea
| | - Sang Yeon Lee
- Department of Materials Science and Engineering, Department of Energy Systems Research, Ajou University, Suwon, 16499, South Korea
| | - Ju Hyun Park
- Department of Energy Engineering, School of Energy and Chemical Engineering, Ulsan National Institute of Science and Technology (UNIST), Ulsan, 44919, South Korea
| | - Hyungtak Seo
- Department of Materials Science and Engineering, Department of Energy Systems Research, Ajou University, Suwon, 16499, South Korea
| | - Sang Kyu Kwak
- Department of Chemical and Biological Engineering, Korea University, Seoul, 02841, South Korea
| | - Sang-Wook Kim
- Department of Molecular Science and Technology, Ajou University, Suwon, 16499, South Korea
| | - Jong H Kim
- Department of Molecular Science and Technology, Ajou University, Suwon, 16499, South Korea
| |
Collapse
|
2
|
Borah D, Saikia P, Sarmah P, Gogoi D, Rout J, Ghosh NN, Bhattacharjee CR. Composition controllable alga-mediated green synthesis of covellite CuS nanostructure: An efficient photocatalyst for degradation of toxic dye. INORG CHEM COMMUN 2022. [DOI: 10.1016/j.inoche.2022.109608] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/16/2023]
|
3
|
Manivelan N, Karuppanan S, Prabakar K. Djurleite Copper Sulfide-Coupled Cobalt Sulfide Interface for a Stable and Efficient Electrocatalyst. ACS APPLIED MATERIALS & INTERFACES 2022; 14:30812-30823. [PMID: 35762731 DOI: 10.1021/acsami.2c06010] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/15/2023]
Abstract
Transition metal sulfides (TMS) exhibit proliferated edge sites, facile electrode kinetics, and improved intrinsic electrical conductivity, which demand low potential requirements for total water splitting application. Here, we have propounded copper sulfide-coupled cobalt sulfide nanosheets grown on 3D nickel as an electrocatalyst for hydrogen (HER) and oxygen evolution (OER) reactions. The formation of djurleite copper sulfide with a Cu vacancy enables faster H+ ion transport and shows improved HER activity with a remarkably lower overpotential of 164 mV at 10 mA/cm2, whereas cobalt-incorporated copper sulfide undergoes cation exchange during synthesis and shows elevated OER activity with a lower overpotential of 240 mV at 10 mA/cm2 for the OER. Moreover, Cu2-xS/Co is said to have a hybrid CoS-CoS2 interface and provide Co2+ active sites on the surface and enable the fast adsorption of intermediate species (OH*, O*, and OOH*), which lowers the potential requirement. The copper vacancy and cation exchange with a hybrid CoS-CoS2 structure are helpful in supplying more surface reactive species and faster ion transport for the HER and OER, respectively. The full-cell electrolyzer requires a very low potential of 1.58 V to attain a current density of 10 mA/cm2, and it shows excellent stability for 50 h at 100 mA/cm2 as confirmed by the chronopotentiometry test.
Collapse
Affiliation(s)
- Nandapriya Manivelan
- Department of Electrical Engineering, Pusan National University, 2 Busandaehak-ro 63beon-gil, Geumjeong-gu, Busan 46241, Republic of Korea
| | - Senthil Karuppanan
- Department of Physics, School of Advanced Sciences, VIT-AP University, Amaravati 522 237, Andhra Pradesh, India
| | - Kandasamy Prabakar
- Department of Electrical Engineering, Pusan National University, 2 Busandaehak-ro 63beon-gil, Geumjeong-gu, Busan 46241, Republic of Korea
| |
Collapse
|
4
|
Xia C, Pedrazo-Tardajos A, Wang D, Meeldijk JD, Gerritsen HC, Bals S, de Mello Donega C. Seeded Growth Combined with Cation Exchange for the Synthesis of Anisotropic Cu 2-x S/ZnS, Cu 2-x S, and CuInS 2 Nanorods. CHEMISTRY OF MATERIALS : A PUBLICATION OF THE AMERICAN CHEMICAL SOCIETY 2021; 33:102-116. [PMID: 33456135 PMCID: PMC7808334 DOI: 10.1021/acs.chemmater.0c02817] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 07/05/2020] [Revised: 11/03/2020] [Indexed: 06/12/2023]
Abstract
Colloidal copper(I) sulfide (Cu2-x S) nanocrystals (NCs) have attracted much attention for a wide range of applications because of their unique optoelectronic properties, driving scientists to explore the potential of using Cu2-x S NCs as seeds in the synthesis of heteronanocrystals to achieve new multifunctional materials. Herein, we developed a multistep synthesis strategy toward Cu2-x S/ZnS heteronanorods. The Janus-type Cu2-x S/ZnS heteronanorods are obtained by the injection of hexagonal high-chalcocite Cu2-x S seed NCs in a hot zinc oleate solution in the presence of suitable surfactants, 20 s after the injection of sulfur precursors. The Cu2-x S seed NCs undergo rapid aggregation and coalescence in the first few seconds after the injection, forming larger NCs that act as the effective seeds for heteronucleation and growth of ZnS. The ZnS heteronucleation occurs on a single (100) facet of the Cu2-x S seed NCs and is followed by fast anisotropic growth along a direction that is perpendicular to the c-axis, thus leading to Cu2-x S/ZnS Janus-type heteronanorods with a sharp heterointerface. Interestingly, the high-chalcocite crystal structure of the injected Cu2-x S seed NCs is preserved in the Cu2-x S segments of the heteronanorods because of the high-thermodynamic stability of this Cu2-x S phase. The Cu2-x S/ZnS heteronanorods are subsequently converted into single-component Cu2-x S and CuInS2 nanorods by postsynthetic topotactic cation exchange. This work expands the possibilities for the rational synthesis of colloidal multicomponent heteronanorods by allowing the design principles of postsynthetic heteroepitaxial seeded growth and nanoscale cation exchange to be combined, yielding access to a plethora of multicomponent heteronanorods with diameters in the quantum confinement regime.
Collapse
Affiliation(s)
- Chenghui Xia
- Debye
Institute for Nanomaterials Science, Utrecht
University, P.O. Box 80000, 3508 TA Utrecht, The Netherlands
| | | | - Da Wang
- EMAT-University
of Antwerp, Groenenborgerlaan
171, B-2020 Antwerp, Belgium
| | - Johannes D. Meeldijk
- Debye
Institute for Nanomaterials Science, Utrecht
University, P.O. Box 80000, 3508 TA Utrecht, The Netherlands
| | - Hans C. Gerritsen
- Debye
Institute for Nanomaterials Science, Utrecht
University, P.O. Box 80000, 3508 TA Utrecht, The Netherlands
| | - Sara Bals
- EMAT-University
of Antwerp, Groenenborgerlaan
171, B-2020 Antwerp, Belgium
| | - Celso de Mello Donega
- Debye
Institute for Nanomaterials Science, Utrecht
University, P.O. Box 80000, 3508 TA Utrecht, The Netherlands
| |
Collapse
|
5
|
Steimle BC, Lord RW, Schaak RE. Phosphine-Induced Phase Transition in Copper Sulfide Nanoparticles Prior to Initiation of a Cation Exchange Reaction. J Am Chem Soc 2020; 142:13345-13349. [PMID: 32700901 DOI: 10.1021/jacs.0c06602] [Citation(s) in RCA: 18] [Impact Index Per Article: 4.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/04/2023]
Abstract
Cation exchange reactions of colloidal copper sulfide nanoparticles are widely used to produce derivative nanoparticles having unique compositions, metastable crystal structures, and complex heterostructures. The copper sulfide crystal structure plays a key role in the mechanism by which cation exchange occurs and the product that forms. Here, we show that digenite copper sulfide nanoparticles undergo a spontaneous phase transition to tetragonal chalcocite in situ, prior to the onset of cation exchange. Room-temperature sonication of digenite (Cu1.8S) in trioctylphosphine, a Lewis base that drives cation exchange, extracts sulfur to produce tetragonal chalcocite (Cu2S). The subtle structural differences between digenite and tetragonal chalcocite are believed to influence the accessibility of cation diffusion channels and concomitantly the mechanism of cation exchange. Structural relationships in nanocrystal cation exchange are therefore dynamic, and intermediates generated in situ must be considered.
Collapse
|
6
|
Li L, Jin Z, Tao R, Li F, Wang Y, Yang X, Xu L. Efficient and low-cost Cu2S-H4SiW12O40/MoS2 counter electrodes in CdS quantum-dot sensitized solar cells with high short-circuit current density. J Photochem Photobiol A Chem 2019. [DOI: 10.1016/j.jphotochem.2019.03.044] [Citation(s) in RCA: 8] [Impact Index Per Article: 1.6] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/23/2023]
|
7
|
Nethravathi C, R. RN, Rajamathi JT, Rajamathi M. Microwave-Assisted Synthesis of Porous Aggregates of CuS Nanoparticles for Sunlight Photocatalysis. ACS OMEGA 2019; 4:4825-4831. [PMID: 31459666 PMCID: PMC6648875 DOI: 10.1021/acsomega.8b03288] [Citation(s) in RCA: 20] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/26/2018] [Accepted: 02/18/2019] [Indexed: 05/26/2023]
Abstract
Solvated two-dimensional nanosheets of copper hydroxy dodecylsulfate in 1-butanol react with thiourea under microwave irradiation to yield surfactant-free porous aggregates of CuS nanoparticles. These aggregates exhibit excellent photocatalytic activity toward degradation of methylene blue, methyl orange, and 4-chlorophenol in natural sunlight. While the high surface area (14.74 m2 g-1) and porosity increase the active reaction centers for adsorption and degradation of organic molecules, quantum confinement results in a low recombination of photogenerated electrons and holes. Chemical and photogenerated hydroxyl radicals cause the oxidation of the dyes and 4-chlorophenol.
Collapse
|
8
|
Dexter M, Gao Z, Bansal S, Chang CH, Malhotra R. Temperature, Crystalline Phase and Influence of Substrate Properties in Intense Pulsed Light Sintering of Copper Sulfide Nanoparticle Thin Films. Sci Rep 2018; 8:2201. [PMID: 29396533 PMCID: PMC5797230 DOI: 10.1038/s41598-018-20621-9] [Citation(s) in RCA: 25] [Impact Index Per Article: 4.2] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/27/2017] [Accepted: 01/22/2018] [Indexed: 12/02/2022] Open
Abstract
Intense Pulsed Light sintering (IPL) uses pulsed, visible light to sinter nanoparticles (NPs) into films used in functional devices. While IPL of chalcogenide NPs is demonstrated, there is limited work on prediction of crystalline phase of the film and the impact of optical properties of the substrate. Here we characterize and model the evolution of film temperature and crystalline phase during IPL of chalcogenide copper sulfide NP films on glass. Recrystallization of the film to crystalline covellite and digenite phases occurs at 126 °C and 155 °C respectively within 2–7 seconds. Post-IPL films exhibit p-type behavior, lower resistivity (~10−3–10−4 Ω-cm), similar visible transmission and lower near-infrared transmission as compared to the as-deposited film. A thermal model is experimentally validated, and extended by combining it with a thermodynamic approach for crystal phase prediction and via incorporating the influence of film transmittivity and optical properties of the substrate on heating during IPL. The model is used to show the need to a-priori control IPL parameters to concurrently account for both the thermal and optical properties of the film and substrate in order to obtain a desired crystalline phase during IPL of such thin films on paper and polycarbonate substrates.
Collapse
Affiliation(s)
- Michael Dexter
- Department of Mechanical and Aerospace Engineering, Rutgers University, Piscataway, New Jersey, 08854, USA
| | - Zhongwei Gao
- Department of Chemical Engineering, Oregon State University, Corvallis, Oregon, 97331, USA
| | - Shalu Bansal
- School of Mechanical, Industrial and Manufacturing Engineering, Oregon State University, Corvallis, Oregon, 97331, USA
| | - Chih-Hung Chang
- Department of Chemical Engineering, Oregon State University, Corvallis, Oregon, 97331, USA
| | - Rajiv Malhotra
- Department of Mechanical and Aerospace Engineering, Rutgers University, Piscataway, New Jersey, 08854, USA.
| |
Collapse
|
9
|
Shahzad R, Kim T, Mun J, Kang SW. Observation of photoluminescence from large-scale layer-controlled 2D ß-Cu 2S synthesized by the vapor-phase sulfurization of copper thin films. NANOTECHNOLOGY 2017; 28:505601. [PMID: 29087360 DOI: 10.1088/1361-6528/aa972b] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/07/2023]
Abstract
Two-dimensional (2D) copper chalcogenides (Cu2-x X where X = S, Se, Te) have had much attention regarding various applications due to their remarkable optical and electrical properties, abundance, and environmentally friendly natures. This work indicates that highly uniform Cu2-x S (where 0 < x < 1) nanosheets can be obtained by the two-step method of Cu deposition by sputtering with precisely controlled and extremely low growth rate followed by vapor-phase sulfurization. The phase transformations of thin Cu2-x S films upon the Cu seed layer thickness are investigated. A unique thickness-constrained synthesis process using vapor-phase sulfurization is employed here, which evolves from a vertical to lateral growth mechanism based on the optimization of the Cu seed layer thickness. Atomically thin 2D β-Cu2S film was successfully synthesized using the thinnest Cu seed film. We have systematically investigated the phase- and thickness-dependent optical properties of Cu2-x S films at room temperature. Micro-photoluminescence (PL) spectroscopy reveals that the 2D β-Cu2S film possesses a direct band gap with an energy of 1.1 eV while the PL intensities are greatly suppressed in the multilayer Cu2-x S (where 0 ≤ x < 1).
Collapse
Affiliation(s)
- Rauf Shahzad
- Advanced Instrumentation Institute, Korea Research Institute of Standards and Science, 267 Gajeong-ro, Yuseong-gu, Daejeon, 305-340, Republic of Korea. Department of Advanced Device technology, University of Science and Technology, 267 Gajeong-ro, Yuseong-gu, Daejeon, 305-340, Republic of Korea
| | | | | | | |
Collapse
|
10
|
Coughlan C, Ibáñez M, Dobrozhan O, Singh A, Cabot A, Ryan KM. Compound Copper Chalcogenide Nanocrystals. Chem Rev 2017; 117:5865-6109. [PMID: 28394585 DOI: 10.1021/acs.chemrev.6b00376] [Citation(s) in RCA: 327] [Impact Index Per Article: 46.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 02/06/2023]
Abstract
This review captures the synthesis, assembly, properties, and applications of copper chalcogenide NCs, which have achieved significant research interest in the last decade due to their compositional and structural versatility. The outstanding functional properties of these materials stems from the relationship between their band structure and defect concentration, including charge carrier concentration and electronic conductivity character, which consequently affects their optoelectronic, optical, and plasmonic properties. This, combined with several metastable crystal phases and stoichiometries and the low energy of formation of defects, makes the reproducible synthesis of these materials, with tunable parameters, remarkable. Further to this, the review captures the progress of the hierarchical assembly of these NCs, which bridges the link between their discrete and collective properties. Their ubiquitous application set has cross-cut energy conversion (photovoltaics, photocatalysis, thermoelectrics), energy storage (lithium-ion batteries, hydrogen generation), emissive materials (plasmonics, LEDs, biolabelling), sensors (electrochemical, biochemical), biomedical devices (magnetic resonance imaging, X-ray computer tomography), and medical therapies (photochemothermal therapies, immunotherapy, radiotherapy, and drug delivery). The confluence of advances in the synthesis, assembly, and application of these NCs in the past decade has the potential to significantly impact society, both economically and environmentally.
Collapse
Affiliation(s)
- Claudia Coughlan
- Department of Chemical Sciences and Bernal Institute, University of Limerick , Limerick, Ireland
| | - Maria Ibáñez
- Catalonia Energy Research Institute - IREC, Sant Adria de Besos , Jardins de les Dones de Negre n.1, Pl. 2, 08930 Barcelona, Spain
| | - Oleksandr Dobrozhan
- Catalonia Energy Research Institute - IREC, Sant Adria de Besos , Jardins de les Dones de Negre n.1, Pl. 2, 08930 Barcelona, Spain.,Department of Electronics and Computing, Sumy State University , 2 Rymskogo-Korsakova st., 40007 Sumy, Ukraine
| | - Ajay Singh
- Materials Physics & Applications Division: Center for Integrated Nanotechnologies, Los Alamos National Laboratory , Los Alamos, New Mexico 87545, United States
| | - Andreu Cabot
- Catalonia Energy Research Institute - IREC, Sant Adria de Besos , Jardins de les Dones de Negre n.1, Pl. 2, 08930 Barcelona, Spain.,ICREA, Pg. Lluís Companys 23, 08010 Barcelona, Spain
| | - Kevin M Ryan
- Department of Chemical Sciences and Bernal Institute, University of Limerick , Limerick, Ireland
| |
Collapse
|
11
|
van der Stam W, Berends AC, de Mello Donega C. Prospects of Colloidal Copper Chalcogenide Nanocrystals. Chemphyschem 2016; 17:559-81. [DOI: 10.1002/cphc.201500976] [Citation(s) in RCA: 112] [Impact Index Per Article: 14.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/31/2015] [Indexed: 01/19/2023]
Affiliation(s)
- Ward van der Stam
- Debye Institute for Nanomaterials Science; Utrecht University; P.O. Box 80000 3508 TA Utrecht The Netherlands
| | - Anne C. Berends
- Debye Institute for Nanomaterials Science; Utrecht University; P.O. Box 80000 3508 TA Utrecht The Netherlands
| | - Celso de Mello Donega
- Debye Institute for Nanomaterials Science; Utrecht University; P.O. Box 80000 3508 TA Utrecht The Netherlands
| |
Collapse
|