Visible-Light-Active BiOI/TiO2 Heterojunction Photocatalysts for Remediation of Crude Oil-Contaminated Water

In this study, BiOI-sensitized TiO2 (BiOI/TiO2) nanocomposites with different levels of BiOI deposited via sequential ionic layer adsorption and reaction (SILAR) have been explored for the degradation of methyl orange, 4-chlorophenol (4-CP), and crude oil in water under visible (>400 nm) irradiation with excellent degradation performance. The reaction progress for methyl orange and 4-chlorophenol was monitored by a UV-vis spectrophotometer, and the degradation of the crude oil hydrocarbons was determined by GC-MS. The BiOI/TiO2 heterojunction improves separation of photogenerated charges, which enhances the degradation efficiency. Evaluation of the visible-light photocatalytic performance of the synthesized catalysts against methyl orange degradation confirmed that four SILAR cycles are the optimal deposition condition for the best degradation efficiency. The efficiency was further confirmed by degrading 4-CP and crude oil, achieving 38.30 and 85.62% degradation, respectively, compared with 0.0% (4-CP) and 70.56% (crude oil) achieved by TiO2. The efficiency of TiO2 in degrading crude oil was mainly due to adsorption along with photolysis. This study provides a simple and cost-effective alternative to traditional remediation methods requiring high energy consumption for remediation of crude oil-polluted water and refinery wastewater using visible-light photocatalysis along with adsorption.

SILAR Deposition of Metal Oxide Nanostructured Films

Methods for the fabrication of thin films with well controlled structure and properties are of great importance for the development of functional devices for a large range of applications. SILAR, the acronym for Successive Ionic Layer Adsorption and Reaction, is an evolution and combination of two other deposition methods, the Atomic Layer Deposition and Chemical Bath Deposition. Due to a relative simplicity and low cost, this method has gained increasing interest in the scientific community. There are, however, several aspects related to the influence of the many parameters involved, which deserve further deepening. In this review article, the basis of the method, its application to the fabrication of thin films, the importance of experimental parameters, and some recent advances in the application of oxide films are reviewed. At first the fundamental theoretical bases and experimental concepts of SILAR are discussed. Then, the fabrication of chalcogenides and metal oxides is reviewed, with special emphasis to metal oxides, trying to extract general information on the effect of experimental parameters on structural, morphological and functional properties. Finally, recent advances in the application of oxide films prepared by SILAR are described, focusing on supercapacitors, transparent electrodes, solar cells, and photoelectrochemical devices.

Nitrogen Doping and Carbon Coating Affects Substrate Selectivity of TiO2 Photocatalytic Organic Pollutant Degradation

A series of carbon-coated, nitrogen-doped titanium dioxide photocatalysts was produced and characterized. N-doped TiO₂ powder samples were prepared using a sol-gel method and subsequently used for making doped-TiO₂ thin films on glass substrates. Carbon layers were coated on the films by a thermal decomposition method using catechol. Diffuse reflectance spectra and Mott-Schottky analyses of the samples proved that nitrogen doping and carbon coating can slightly lower the band gap of TiO₂ , broaden its absorption to visible light and enhance its n-type character. According to photocatalytic tests against model contaminants, carbon-coated nitrogen-doped TiO₂ films have better performance than simple TiO₂ on the degradation of Rhodamine B dye molecules, but are poorly effective for degrading 4-chlorophenol molecules. Several possible explanations are proposed for this result, supported by scavenging experiments. This reveals the importance of a broad substrate scope when assessing new photocatalytic materials for water treatment, something which is often overlooked in many literature studies.

TiO2-Doped Chitosan Microspheres Supported on Cellulose Acetate Fibers for Adsorption and Photocatalytic Degradation of Methyl Orange

Chitosan/cellulose acetate (CS/CA) used as a biopolymer systema, with the addition of TiO2 as photocatalyst (C-T/CA) were fabricated by alternating electrospinning/electrospraying technology. The uniform dispersion of TiO2 and its recovery after the removal of methyl orange (MO) was achieved by incorporating TiO2 in CS electrosprayed hemispheres. The effects of pH values, contact time, and the amount of TiO2 on adsorption and photocatalytic degradation for MO of the C-T/CA were investigated in detail. When TiO2 content was 3 wt %, the highest MO removal amount for fiber membranes (C-T-3/CA) reached 98% at pH value 4 and MO concentration of 40 mg/L. According to the data analysis, the pseudo-second-order kinetic and Freundlich isotherm model were well fitted to kinetic and equilibrium data of MO removal. Especially for C-T-3/CA, the fiber membrane exhibited multiple layers of adsorption. All these results indicated that adsorption caused by electrostatic interaction and photocatalytic degradation were involved in the MO removal process. This work provides a potential method for developing a novel photocatalyst with excellent catalytic activity, adsorbing capability and recycling use.