Site-Selective Chemical Reaction on Flexible Polymer Films for Tin Oxide Nanosheet Patterning

Facet-Controlled Synthesis of CeO2 Nanoparticles for High-Performance CeO2 Nanoparticle/SnO2 Nanosheet Hybrid Gas Sensors

CeO2 nanocubes with metastable {100} facets and CeO2 nanooctahedrons with the most stable {111} facets are herein fabricated by controlling the morphology and facets of CeO2 nanoparticles. SnO2 nanosheet-based assembled films coated with these CeO2 nanocubes or CeO2 nanooctahedrons yield {100} CeO2 nanocubes/SnO2 nanosheets and {111} CeO2 nanooctahedron/SnO2 nanosheet hybrid gas sensors, respectively. The hybrid sensors with CeO2 nanoparticles exhibited enhanced sensing responses to numerous chemical species relative to a pristine SnO2 nanosheet gas sensor, including acetone, hydrogen, ethanol, ammonia, acetaldehyde, and allyl mercaptan. In particular, the responses of {100} CeO2 nanocubes/SnO2 nanosheets and {111} CeO2 nanooctahedron/SnO2 nanosheet gas sensors to acetone or allyl mercaptan were 6.8 and 10.3 times higher, respectively, than that of the pristine SnO2 nanosheet gas sensor. Furthermore, the sensor response to ammonia was 2.5 times higher than that of a commercial volatile organic compound (VOC) gas sensor (TGS2602, Figaro Engineering Inc.). The CeO2 nanocube-based sensor with exposed metastable {100} facets promotes the adsorption and oxidation of VOCs owing to the higher surface energy of the metastable {100} facets and therefore exhibits a higher sensing performance than the CeO2 nanooctahedron-based sensor with an exposed {111} facet. The developed sensors show excellent potential for the detection of gas markers in human breath and perspiration for disease diagnosis.

Facet controlled growth mechanism of SnO2 (101) nanosheet assembled film via cold crystallization

Cold crystallization of SnO₂ was realized in aqueous solutions, where crystal growth was controlled to form SnO₂ (101) nanosheet assembled films for devices such as chemical sensors. The nanosheets grew directly on a fluorine-doped tin oxide substrate without a seed layer or a buffer layer. The nanosheets had a thickness of 5–10 nm and an in-plane size of 100–1600 nm. Moreover, the large flat surface of the (101) facet was metastable. The thickness of the SnO₂ (101) nanosheet assembled film was approximately 800 nm, and the film had a gradient structure that contained many connected nanosheets. TEM results revealed that the predominate branch angles between any two connected nanosheets were 90° and 46.48°, corresponding to type I and type II connections, respectively. These connections were consistent with the calculations based on crystallography. Crystallographic analysis clarified the characteristic crystal growth of the SnO₂ (101) nanosheet assembled film in the aqueous solution. Furthermore, we demonstrate that the metastable (101) facet can be exploited to control the rate of crystal growth by adjusting the etching condition.

Fabrication and H2-Sensing Properties of SnO2 Nanosheet Gas Sensors

Vertically formed and well-defined SnO₂ nanosheets are easy to fabricate, involving only a single process that is performed under moderate conditions. In this study, two different sizes of a SnO₂ nanosheet were concurrently formed on a Pt interdigitated electrode chip, with interconnections between the two. As the SnO₂ nanosheets were grown over time, the interconnections became stronger. The ability of the fabricated SnO₂ nanosheets to sense H₂ gas was evaluated in terms of the variation in their resistance. The resistance of a SnO₂ nanosheet decreased with the introduction of H₂ gas and returned to its initial level after the H₂ gas was replaced with air. Also, the response-recovery behaviors were improved as a result of the growth of the SnO₂ nanosheets owing to the presence of many reaction sites and strong interconnections, which may provide multipassages for the electron transfer channel, leading to the acceleration of the reaction between the H₂ gas and SnO₂ nanosheets.

Tin oxide nanosheet assembly for hydrophobic/hydrophilic coating and cancer sensing

Tin oxide nanosheets were crystallized on transparent conductive oxide substrates of fluorine-doped tin oxide in aqueous solutions. The nanosheets had chemical ratio of Sn:O:F = 1:1.85:0.076, suggesting fluorine doping into SnO(2). They were hydrophobic surfaces with contact angle of 140°. They were converted to hydrophilic surfaces with contact angle of below 1° by light irradiation. The simple water process will be applied to surface coating of polymers, metals, biomaterials, papers, etc. Furthermore, the tin oxide nanosheets were modified with dye-labeled monoclonal antibody. Monoclonal antibody reacts with human alpha-fetoprotein in blood serum of hepatocellular cancer patient. Photoluminescence and photocurrent were obtained from the nanosheets under excitation light. Photoelectric conversion was an essence in the sensing system. The tin oxide nanosheets with dye-labeled prostate specific antigen will be used for electrodes of prostate cancer sensors.