Signal Generation at an Electrochemical Immunosensor via the Direct Oxidation of an Electroactive Label

Antibody-Electroactive Probe Conjugates Based Electrochemical Immunosensors

Suitable immobilization of a biorecognition element, such as an antigen or antibody, on a transducer surface is essential for development of sensitive and analytically reliable immunosensors. In this review, we report on (1) methods of antibody prefunctionalization using electroactive probes, (2) methods for immobilization of such conjugates on the surfaces of electrodes in electrochemical immunosensor construction and (3) the use of antibody-electroactive probe conjugates as bioreceptors and sensor signal generators. We focus on different strategies of antibody functionalization using the redox active probes ferrocene (Fc), anthraquinone (AQ), thionine (Thi), cobalt(III) bipyridine (Co(bpy)33+), Ru(bpy)32+ and horseradish peroxidase (HRP). In addition, new possibilities for antibody functionalization based on bioconjugation techniques are presented. We discuss strategies of specific, quantitative antigen detection based on (i) a sandwich format and (ii) a direct signal generation scheme. Further, the integration of different nanomaterials in the construction of these immunosensors is presented. Lastly, we report the use of a redox probe strategy in multiplexed analyte detection.

Square wave voltammetry versus electrochemical impedance spectroscopy as a rapid detection technique at electrochemical immunosensors

Square wave voltammetry (SWV) was compared to electrochemical impedance spectroscopy (EIS) in developing a label-free electrochemical immunosensor for the hormone estradiol. The immunosensor consists of a Au electrode anchored with a Au nanoparticle|thiolated Protein G-scaffold to facilitate immobilisation of an enhanced quantity of an almost uprightly aligned anti-estradiol capture antibody. Competitive immunoassays between an estradiol-bovine saline albumin complex and free estradiol in a sample were then promoted at the immunosensor. Next, SWV and EIS of [Fe(CN)(6)](3-/4-) were sequentially conducted at the immunosensor. SWV yielded familiar peak-shaped voltammograms with the peak currents readily employable in establishing calibration. A dynamic range up to approximately 1200 pg mL(-1) and a detection limit of 18 pg mL(-1) estradiol were achieved. In EIS, an electron transfer resistance estimated from the Nyquist plots was used in the calibration experiments. A comparable dynamic range up to approximately 1000 pg mL(-1) and a detection limit of 26 pg mL(-1) estradiol were obtained. However, a significantly 10 times longer analysis time and substantial effort were required to complete the EIS determinations relative to SWV. Moreover, a large amount of EIS data involving phase angle was collected but ignored because they would not contribute any useful information to quantitative determination. Overall, SWV was determined to be a more rapid, efficient, effective and low cost detection technique than EIS at label-free electrochemical immunosensors.

Amperometric micro-immunosensor for the detection of tumor biomarker

In this paper, a highly sensitive, reagentless, electrochemical strategy is reported for the detection of a cancer biomarker-Vascular Endothelial Growth Factor (VEGF). Disc shaped carbon fiber microelectrodes were used as the immunosensor platform. Ferrocene monocarboxylic acid labeled anti-VEGF was covalently immobilized on the microelectrode surface using a Jeffamine cross-linker. The formation of immunocomplexes leads to a decrease in the electrochemical signal of ferrocene monocarboxylic acid owing to increased spatial blocking of microelectrode surface. These signal changes enable quantitative detection of VEGF in solution. Voltammetric measurements were conducted to evaluate the interfacial immunoreactions and to quantitatively detect VEGF biomarker. The proposed immunosensing strategy allows a rapid and sensitive means of VEGF analysis with a limit of detection of about 38 pg/mL. This opens up the possibility of employing these electrodes for various single cell analysis and clinical applications. Further, experimental conditions such as concentration of the immobilized antibodies and incubation period were optimized. Following this, the stability and specificity of the immunosensors were also evaluated.

Point-of-care testing of proteins

Point-of-care testing (POCT) is a fast developing area in clinical diagnostics that is considered to be one of the main driving forces for the future in vitro diagnostic market. POCT means decentralized testing at the site of patient care. The most important POCT devices are handheld blood glucose sensors. In some of these sensors, after the application of less than 1 microl whole blood, the results are displayed in less than 10 s. For protein determination, the most commonly used devices are based on lateral flow technology. Although these devices are convenient to use, the results are often only qualitative or semiquantitative. The review will illuminate some of the current methods employed in POCT for proteins and will discuss the outlook for techniques (e.g., electrochemical immunosensors) that could have a great impact on future POCT of proteins.

Over-the-Counter Biosensors: Past, Present, and Future

The demand for specific, low cost, rapid, sensitive and easy detection of biomolecules is huge. A well-known example is the glucose meters used by diabetics to monitor their blood glucose levels. Nowadays, a vast majority of the glucose meters are based on electrochemical biosensor technology. The inherent small size and simple construction of the electrochemical transducer and instrument are ideally suited for point-of-care biosensing. Besides glucose, a wide variety of electrochemical biosensors have been developed for the measurements of some other key metabolites, proteins, and nucleic acids. Nevertheless, unlike the glucose meters, limited success has been achieved for the commercialization of the protein and nucleic acid biosensors. In this review article, key technologies on the electrochemical detection of key metabolites, proteins, and DNAs are discussed in detail, with particular emphasis on those that are compatible to home-use setting. Moreover, emerging technologies of lab-on-a-chip microdevices and nanosensors (i.e., silicon and carbon nanotube field-effect sensors) offer opportunities for the construction of new generation biosensors with much better performances. Together with the continuous innovations in the basic components of biosensors (i.e., transducers, biorecognition molecules, immobilization and signal transduction schemes), consumers could soon buy different kinds of biosensing devices in the pharmacy stores.

Electrochemical biochips for protein analysis

Proteins bear important functions for most life processes. It is estimated that the human proteome comprises more than 250,000 proteins. Over the last years, highly sophisticated and powerful instruments have been developed that allow their detection and characterization with great precision and sensitivity. However, these instruments need well-equipped laboratories and a well-trained staff. For the determination of proteins in a hospital, in a doctor's office, or at home, low-budget protein analysis methods are needed that are easy to perform. In addition, for a proteomic approach, highly parallel measurements with small sample sizes are required. Biochips are considered as promising tools for such applications. The following chapter describes electrochemical biochips for protein analysis that use antibodies or aptamers as recognition elements.

Ferrocene-based derivatization in analytical chemistry

Ferrocene-based derivatization has raised considerable interest in many fields of analytical chemistry. This is due to the well-established chemistry of ferrocenes, which allows rapid and easy access to a large number of reagents and derivatives. Furthermore, the electrochemical properties of ferrocenes are attractive with respect to their detection. This paper summarizes the available reagents, the reaction conditions and the different approaches for detection. While electrochemical detection is still most widely used to detect ferrocene derivatives, e.g., in the field of DNA analysis, the emerging combination of analytical separation methods with electrochemistry, mass spectrometry and atomic spectroscopy allows ferrocenes to be applied more universally and in novel applications where strongly improved selectivity and limits of detection are required.

Enzyme activity control by responsive redoxpolymers

A new thermoresponsive poly-N-isopropylacrylamide (PNIPAM)-ferrocene polymer was synthesized and characterized. PNIPAMFoxy bears additional oxirane groups which were used for attachment by a self-assembly process on a cysteamine-modified gold electrode to create a thin hydrophilic film. The new redox polymer enabled electrical communication between the cofactor pyrrolinoquinoline quinone (PQQ) of soluble glucose dehydrogenase (sGDH) and the electrode for sensitive detection of this enzyme as a prospective protein label. The temperature influence on the redox polymer/enzyme complex was investigated. An inverse temperature response behavior of surface bound PNIPAMFoxy compared to the soluble polymer was found and is discussed in detail. The highest efficiency of mediated electron transfer for the immobilized PNIPAMFoxy with sGDH was observed at 24 degrees C, which was twice as high as that of its soluble counterpart. A steady-state electrooxidation current densitiy of 4.5 microA.cm-2 was observed in the presence of 10 nM sGDH and 5 mM glucose. A detection limit of 0.5 nM of soluble PQQ-sGDH was obtained.