Highly flexible Ag nanowire network covered by a graphene oxide nanosheet for high-performance flexible electronics and anti-bacterial applications

We investigated a flexible and transparent conductive electrode (FTCE) based on Ag nanowires (AgNWs) and a graphene oxide (GO) nanosheet and fabricated through a simple and cost-effective spray coating method. The AgNWs/GO hybrid FTCE was optimized by adjusting the nozzle-to-substrate distance, spray speed, compressor pressure, and volume of the GO solution. The optimal AgNWs/GO hybrid FTCE has a high transmittance of 88% at a wavelength of 550 nm and a low sheet resistance of 20 Ohm/square. We demonstrate the presence of the GO nanosheet on the AgNWs through Raman spectroscopy. Using scanning electron microscopy and atomic force microscopy, we confirmed that the nanosheet acted as a conducting bridge between AgNWs and improved the surface morphology and roughness of the electrode. Effective coverage by the GO sheet improved the conductivity of the AgNWs electrode Effective coverage of the GO sheet improved conductivity of the AgNWs electrode with minimum degradation of optical and mechanical properties. Flexible thin film heater (TFH) and electroluminescent (EL) devices fabricated on AgNWs/GO hybrid FTCEs showed better performance than devices on bare AgNWs electrodes due to lower sheet resistance and uniform conductivity. In addition, an AgNWs/GO electrode layer on a facial mask acts as a self-heating and antibacterial coating. A facial mask with an AgNWs/GO electrode showed a bacteriostatic reduction rate of 99.7 against Staphylococcus aureus and Klebsiella pneumonia.

Using airbrushes to pattern reagents for microarrays and paper-fluidic devices

We report using an airbrush to pattern a number of reagents, including small molecules, proteins, DNA, and conductive microparticles, onto a variety of mechanical substrates such as paper and glass. Airbrushing is more economical and easier to perform than many other patterning methods available (for example, inkjet printing). In this work, we investigated the controllable parameters that affect patterned line width and studied their mechanisms of action, and we provide examples of possible patterns. This airbrushing approach allowed us to pattern lines and dot arrays from hundreds of μm to tens of mm with length scales comparable to those of other patterning methods. Two applications, enzymatic assays and DNA hybridization, were chosen to demonstrate the compatibility of the method with biomolecules. This airbrushing method holds promise in making paper-based platforms less expensive and more accessible.

A cyclo olefin polymer microfluidic chip with integrated gold microelectrodes for aqueous and non-aqueous electrochemistry

This paper presents an entirely polymeric microfluidic system, made of cyclo olefin polymer (COP), with integrated gold microband electrodes for electrochemical applications in organic media. In the present work, we take advantage of the COP's high chemical stability to polar organic solvents in two different ways: (i) to fabricate gold microelectrodes using COP as a substrate by standard lithographic and lift-off techniques; and (ii) to perform electrochemical experiments in organic media. In particular, fourteen parallel gold microelectrodes with a width of 14 microm and separated from their closest neighbour by 16 microm were fabricated by lithographic and lift-off techniques on a 188 microm thick COP sheet. A closed channel configuration was obtained by pressure-assisted thermal bonding between the COP sheet containing the microelectrodes and a microstructured COP sheet, where a 3 cm long, 50 microm wide and 24 microm deep channel was fabricated via hot embossing. Cyclic voltammetric measurements were carried out in aqueous and organic media, using a solution consisting of 5 mM ferrocyanide/ferricyanide in 0.5 M KNO(3) and 5 mM ferrocene in 0.1 M TBAP/acetonitrile, respectively. Experimental currents obtained for different flow rates ranging from 1 to 10 microL min(-1) were compared to the theoretical steady state currents calculated by the Levich equation for a band electrode (R. G. Compton, A. C. Fisher, R. G. Wellington, P. J. Dobson and P. A. Leigh, J. Phys. Chem., 1993, 97, 10410-10415). In both cases, the difference between the experimental and the predicted data is less than 5%, thus validating the behaviour of the fabricated device. This result opens the possibility to use a microfluidic system made entirely from COP with integrated microband electrodes in organic electroanalysis and in electrosynthesis.

Screen printed electrochemical platforms for pH sensing

We explore the possible use of screen printing technology for fabricating disposable electrochemical platforms for the sensing of pH. These screen printed pH sensors incorporate the pH sensitive phenanthraquinone moiety which undergoes a Nernstian potential shift with pH, and the pH insensitive dimethylferrocene which acts as an internal reference. This generic approach offers a calibration-less and reproducible approach for portable pH measurements with the possibility of miniaturisation allowing incorporation into existing sensing devices. The advantages, limitations and future prospects of this fabrication approach for producing electrochemical platforms for pH sensing are also discussed.