Improving the Upper Detection Limit of Potentiometric Sensors

Physically Tailoring Ion Fluxes by Introducing Foamlike Structures into Polymeric Membranes of Solid Contact Ion-Selective Electrodes

Transmembrane ion fluxes have earlier been identified as a source of potential instability in solid contact ion-selective electrodes (SC-ISEs). In this work, foamlike structures were intentionally introduced into a potassium-sensitive plasticized poly(vinyl chloride) ion-selective membrane (ISM) near the membrane|solid contact interface by controlling the temperature during membrane deposition. Foamlike structures in the ISM were shown to be effective at physically tailoring the transport of ions in the ion-selective membrane, greatly reducing the flux of interfering ions from the sample to the membrane|solid contact interface. The drifts during a conventional water layer test were hence able to be greatly mitigated, even with SC-ISEs incorporating a relatively hydrophilic poly(3,4-ethylenedioxythiophene) doped with poly(styrenesulfonate) (PEDOT:PSS) solid contact. In solutions with a high background concentration of interfering ions, equilibrated ion-selective electrodes with foamlike membranes were able to reproduce their initial potentials within 0.6 mV uncertainty (n = 3) from 0 to 18 h. This was achieved despite sensor exposure to solutions exceeding the selectivity limit of the ISEs in 3 h intervals, allowing improvement of the potential reproducibility of the sensors. Since the introduction of foamlike structures into ISM is linked to temperature-controlled membrane deposition, it is envisaged that the method is generally applicable to all solid contact ion-selective electrodes that are based on polymeric membranes and require membrane deposition from the cocktail solution.

Insights into Primary Ion Exchange between Ion-Selective Membranes and Solution. From Altering Natural Isotope Ratios to Isotope Dilution Inductively Coupled Plasma Mass Spectrometry Studies

Although ion-selective electrodes have been routinely used for decades now, there are still gaps in experimental evidence regarding how these sensors operate. This especially applies to the exchange of primary ions occurring for systems already containing analyte ions from the pretreatment step. Herein, for the first time, we present an insight into this process looking at the effect of altered ratios of naturally occurring analyte isotopes and achieving isotopic equilibrium. Benefiting from the same chemical properties of all isotopes of analyte ions and spatial resolution offered by laser ablation and inductively coupled plasma mass spectrometry, obtaining insights into primary ion diffusion in the preconditioned membrane is possible. For systems that have reached isotopic equilibrium in the membrane through ion exchange and between the membrane phase and the sample, quantification of primary ions in the membrane is possible using an isotope dilution approach for a heterogeneous system (membrane-liquid sample). Experimental results obtained for silver-selective membrane show that the primary ion diffusion coefficient in the preconditioned membrane is close to (6 ± 1) × 10^-9 cm²/s, being somewhat lower compared to the previously reported values for other cations. Diffusion of ions in the membrane is the rate limiting step in achieving isotopic exchange equilibrium between the ion-selective membrane phase and sample solution. On the contrary to previous reports, quantification of silver present in the membrane clearly shows that contact of the membrane with silver nitrate solution of concentration 10^-3 M leads to pronounced accumulation of silver ions in the membrane, reaching almost 150% of ion exchanger amount. The magnitude of this effect increases for higher concentration of the electrolyte in the solution.

Unintended Changes of Ion-Selective Membranes Composition-Origin and Effect on Analytical Performance

Ion-selective membranes, as used in potentiometric sensors, are mixtures of a few important constituents in a carefully balanced proportion. The changes of composition of the ion-selective membrane, both qualitative and quantitative, affect the analytical performance of sensors. Different constructions and materials applied to improve sensors result in specific conditions of membrane formation, in consequence, potentially can result in uncontrolled modification of the membrane composition. Clearly, these effects need to be considered, especially if preparation of miniaturized, potentially disposable internal-solution free sensors is considered. Furthermore, membrane composition changes can occur during the normal operation of sensors—accumulation of species as well as release need to be taken into account, regardless of the construction of sensors used. Issues related to spontaneous changes of membrane composition that can occur during sensor construction, pre-treatment and their operation, seem to be underestimated in the subject literature. The aim of this work is to summarize available data related to potentiometric sensors and highlight the effects that can potentially be important also for other sensors using ion-selective membranes, e.g., optodes or voltammetric sensors.