Enzyme Deposition by Polydimethylsiloxane Stamping for Biosensor Fabrication

Microcontact printing of choline oxidase using a polycation-functionalized zwitterionic polymer as enzyme immobilization matrix

Highly sensitive and selective choline microbiosensors were constructed by microcontact printing (μCP) of choline oxidase (ChOx) in a crosslinked, polyamine-functionalized zwitterionic polymer matrix on microelectrode arrays (MEAs). μCP has emerged as a potential means to create implantable, multiplexed sensor microprobes, which requires the targeted deposition of different sensor materials to specific microelectrode sites on a MEA. However, the less than sufficient enzyme loading and inadequate spatial resolution achieved with current μCP approaches has limited adoption of the method for electroenzymatic microsensors. A novel polymer, poly(2-methacryloyloxyethyl phosphorylcholine)-g-poly(allylamine hydrochloride) (PMPC-g-PAH), has been developed to address this challenge. PMPC-g-PAH contributes to a higher viscosity "ink" that enables thicker immobilized ChOx deposits of high spatial resolution while also providing a hydrophilic, biocompatible microenvironment for the enzyme. Electroenzymatic choline microbiosensors with sensitivity of 639 ± 96 nA μM-1 cm-2 (pH 7.4; n = 4) were constructed that also are selective against both ascorbic acid and dopamine, which are potential electroactive interfering compounds in the mammalian brain. The high sensitivities achieved can lead to smaller MEA microprobes that minimize tissue damage and make possible the monitoring of multiple neurochemicals simultaneously in vivo with high spatial resolution.

Fabrication and Optimization of Nafion as a Protective Membrane for TiN-Based pH Sensors

In this study, a solid-state modified pH sensor with RF magnetron sputtering technology was developed. The sensor consists of an active electrode consisting of a titanium nitride (TiN) film with a protective membrane of Nafion and a reference glass electrode of Ag/AgCl. The sensitivity of the pH sensor was investigated. Results show a sensor with excellent characteristics: sensitivity of 58.6 mV/pH for pH values from 2 to 12, very short response time of approximately 12 s in neutral pH solutions, and stability of less than 0.9 mV in 10 min duration. Further improvement in the performance of the TiN sensor was studied by application of a Nafion protective membrane. Nafion improves the sensor sensitivity close to Nernstian by maintaining a linear response. This paves the way to implement TiN with Nafion protection to block any interference species during real time applications in biosensing and medical diagnostic pH sensors.

Recent trends in the applications of thermally expanded graphite for energy storage and sensors - a review

Carbon nanomaterials such as carbon dots (0D), carbon nanotubes (1D), graphene (2D), and graphite (3D) have been exploited as electrode materials for various applications because of their high active surface area, thermal conductivity, high chemical stability and easy availability. In addition, due to the strong affinity between carbon nanomaterials and various catalysts, they can easily form metal carbides (examples: ionic, covalent, interstitial and intermediate transition metal carbides) and also help in the stable dispersion of catalysts on the surface of carbon nanomaterials. Thermally expanded graphite (TEG) is a vermicular-structured carbon material that can be prepared by heating expandable graphite up to 1150 °C using a muffle or tubular furnace. At high temperatures, the thermal expansion of graphite occurred by the intercalation of ions (examples: SO4 2-, NO3 -, Li+, Na+, K+, etc.) and oxidizing agents (examples: ammonium persulfate, H2O2, potassium nitrate, potassium dichromate, potassium permanganate, etc.) which helped in the exfoliation process. Finally, the obtained TEG, an intumescent form of graphite, has been used in the preparation of composite materials with various conducting polymers (examples: epoxy, poly(styrene-co-acrylonitrile), polyaniline, etc.) and metal chlorides (examples: FeCl3, CuCl2, and ZnCl2) for hydrogen storage, thermal energy storage, fuel cells, batteries, supercapacitors, sensors, etc. The main features of TEG include a highly porous structure, very lightweight with an apparent density (0.002-0.02 g cm-3), high mechanical properties (10 MPa), thermal conductivity (25-470 W m-1 K-1), high electrical conductivity (106-108 S cm-1) and low-cost. The porosity and expansion ratio of graphite layers could be customized by controlling the temperature and selection of intercalation ions according to the demand. Recently, TEG based composites prepared with metal oxides, chlorides and polymers have been demonstrated for their use in energy production, energy storage, and electrochemical (bio-) sensors (examples: urea, organic pollutants, Cd2+, Pb2+, etc.). In this review, we have highlighted and summarized the recent developments in TEG-based composites and their potential applications in energy storage, fuel cells and sensors with hand-picked examples.

An implantable multifunctional neural microprobe for simultaneous multi-analyte sensing and chemical delivery

A multifunctional chemical neural probe fabrication process exploiting PDMS thin-film transfer to incorporate a microfluidic channel onto a silicon-based microelectrode array (MEA) platform, and enzyme microstamping to provide multi-analyte detection is described. The Si/PDMS hybrid chemtrode, modified with a nano-based on-probe IrOx reference electrode, was validated in brain phantoms and in rat brain.

Microbiosensor fabrication by polydimethylsiloxane stamping for combined sensing of glucose and choline

High performance microprobes for combined sensing of glucose and choline were fabricated using microcontact printing (μCP) to transfer choline oxidase (ChOx) and glucose oxidase (GOx) onto targeted sites on microelectrode arrays (MEAs). Most electroenzymatic sensing sites on MEAs for neuroscience applications are created by manual enzyme deposition, which becomes problematic when the array feature size is less than or equal to ∼100 μm. The μCP process used here relies on use of soft lithography to create features on a polydimethylsiloxane (PDMS) microstamp that correspond to the dimensions and array locations of targeted, microscale sites on a MEA. Precise alignment of the stamp with the MEA is also required to transfer enzyme only onto the specified microelectrode(s). The dual sensor fabrication process began with polyphenylenediamine (PPD) electrodeposition on all Pt microelectrodes to block common interferents (e.g., ascorbic acid and dopamine) found in brain extracellular fluid. Next, a chitosan film was electrodeposited to serve as an adhesive layer. The two enzymes, ChOx and GOx, were transferred onto different microelectrodes of 2 × 2 arrays using two different PDMS stamps and a microscope for stamp alignment. Using constant potential amperometry, the combined sensing microprobe was confirmed to have high sensitivity for choline and glucose (286 and 117 μA mM cm-2, respectively) accompanied by low detection limits (1 and 3 μM, respectively) and rapid response times (≤2 s). This work demonstrates the use of μCP for facile creation of multianalyte sensing microprobes by targeted deposition of enzymes onto preselected sites of a microelectrode array.