Inkjet Printed Multi‐walled Carbon Nanotube Sensor for the Detection of Lead in Drinking Water

Screen-Printed Sensors Modified with Nafion and Mesoporous Carbon for Electrochemical Detection of Lead in Blood

Lead (Pb) has long been acknowledged as a systemic toxicant, with pronounced health impacts observed even at low exposure levels, particularly in children. Adverse effects include diminished cognitive function, altered behavior, and developmental delays. Consequently, it is imperative to conduct regular monitoring of Blood Lead Levels (BLLs). In this work, we report on an electrochemical sensor based on screen-printed carbon electrode (SPCE) coated with Nafion and mesoporous carbon (MC). The sensor system uses simple sample preparation (acidification and dilution of whole blood), minimal sample volume (a few blood drops, 200 μl), and swift time-to-results (1 h). A limit of quantitation (LOQ) of 0.3 μg dL-1 Pb was achieved in whole blood. To demonstrate the practical utility of our sensor system, we evaluated its performance in the analysis of blood samples collected from children (n = 25). Comparative analysis with the laboratory-based gold standard method of inductively coupled plasma mass spectrometry (ICP-MS) demonstrated approximately 77% accuracy and 94% precision. We anticipate that our approach will serve as a valuable tool for more frequent BLL monitoring, particularly in communities where access to laboratory testing is impractical or expensive.

One-step electrochemical elaboration of SnO2 modified electrode for lead ion trace detection in drinking water using SWASV

A facile method was proposed for the elaboration of an electrochemical sensor for heavy metal's trace detection by using square wave anodic stripping voltammetry (SWASV); this method is based on a simple anodic conversion of tin electrode into Sn/SnO₂ modified electrode. Both electrochemical and physico-chemical techniques were used to confirm the modification process and better understand the electrode's behavior. Then, depending on the operating conditions, the response signal was studied and adjusted in order to obtain optimal sensor performance. When optimized, the proposed method reached a lowest detection limit (LOD) of 2.15 μg L^-1 (0.0104 μM), and quantification limit (LOQ) of 5.36 μg L^-1 (0.0259 μM), in linearity range between from 6.2 and 20.7 μg L^-1. Additionally, after having used the elaborated electrode for ten successive measurements, the repeatability remains very high with an RSD of approximately 5.3%; furthermore, ten other species appear to have very slight effect on Pb(II) detection. Finally, for the method validation, the proposed electrode was able to sense different lead concentration integrated in a local bottled spring water by showing recovery levels ranging from 103.8 to 108.4%.

Carbon Nanomaterials-Based Electrochemical Sensors for Heavy Metal Detection

Heavy metals are commonly found in a wide range of environmental settings metals, but the potential toxicity associated with heavy metal exposure represents a major threat to global public health. It is thus vital that approaches to efficiently, reliably, and effectively detecting heavy metals in a range of sample types be established. Carbon nanomaterials offer many advantageous properties that make them well-suited to the design of sensitive, selective, easy-to-operate electrochemical biosensors ideal for detecting heavy metal ions. The present review offers an overview of recent progress in the development of carbon nanomaterial-based electrochemical sensors used to detect heavy metals. In addition to providing a detailed discussion of certain carbon nanomaterials such as carbon nanotubes, graphene, carbon fibers, carbon quantum dots, carbon nanospheres, mesoporous carbon, and Graphdiyne, we survey the challenges and future directions for this field. Overall, the studies discussed herein suggest that the further development of carbon nanomaterial-modified electrochemical sensors will support the integration of increasingly advanced sensor platforms to aid in detecting heavy metals in foods, environmental samples, and other settings, thereby benefitting human health and society as a whole.

Impact of physical and chemical parameters on square wave anodic stripping voltammetry for trace Pb2+ detection in water

Exposure to lead, a toxic heavy metal, in drinking water is a worldwide problem.

Electrical and Electrochemical Sensors Based on Carbon Nanotubes for the Monitoring of Chemicals in Water-A Review

Carbon nanotubes (CNTs) combine high electrical conductivity with high surface area and chemical stability, which makes them very promising for chemical sensing. While water quality monitoring has particularly strong societal and environmental impacts, a lot of critical sensing needs remain unmet by commercial technologies. In the present review, we show across 20 water monitoring analytes and 90 references that carbon nanotube-based electrochemical sensors, chemistors and field-effect transistors (chemFET) can meet these needs. A set of 126 additional references provide context and supporting information. After introducing water quality monitoring challenges, the general operation and fabrication principles of CNT water quality sensors are summarized. They are sorted by target analytes (pH, micronutrients and metal ions, nitrogen, hardness, dissolved oxygen, disinfectants, sulfur and miscellaneous) and compared in terms of performances (limit of detection, sensitivity and detection range) and functionalization strategies. For each analyte, the references with best performances are discussed. Overall, the most frequently investigated analytes are H+ (pH) and lead (with 18% of references each), then cadmium (14%) and nitrite (11%). Micronutrients and toxic metals cover 40% of all references. Electrochemical sensors (73%) have been more investigated than chemistors (14%) or FETs (12%). Limits of detection in the ppt range have been reached, for instance Cu(II) detection with a liquid-gated chemFET using SWCNT functionalized with peptide-enhanced polyaniline or Pb(II) detection with stripping voltammetry using MWCNT functionalized with ionic liquid-dithizone based bucky-gel. The large majority of reports address functionalized CNTs (82%) instead of pristine or carboxyl-functionalized CNTs. For analytes where comparison is possible, FET-based and electrochemical transduction yield better performances than chemistors (Cu(II), Hg(II), Ca(II), H2O2); non-functionalized CNTs may yield better performances than functionalized ones (Zn(II), pH and chlorine).

Co@N-CNT/MXenes in situ grown on carbon nanotube film for multifunctional sensors and flexible supercapacitors

The rapid development of human-machine interfaces and artificial intelligence is dependent on flexible and wearable soft devices such as sensors and energy storage systems. One of the key factors for these devices is the design of a flexible electrode with high sensitivity, fast response time, and a wide working range. Here, we report the fabrication of strain sensors and all-solid-state flexible supercapacitors using Co@N-CNT/MXenes as an electrode material. The manufactured sensor shows a high tensile range (strain up to 200%) and high stability. The resistance change caused by the fingers touching the sensor can be used to transmit the Morse code information. Flexible supercapacitors serving as power supply demonstrate excellent cycling stability (85 000 cycles) and coulombic efficiency (99.7%) for their high surface area and pseudocapacitance. A self-powered integrated system composed of the strain sensor and flexible supercapacitor is fabricated and operates stably in a wide strain sensing test range. Moreover, the flexible solar-charging self-powered integrated system could be attached to the human body for stable human motion detection. This study clearly shows that appropriate selection of a single functional material to enable it to be used in multi-functional sensors and supercapacitors can simplify the process and reduce the cost of manufacturing wearable devices.

Carbon Nanotube Microelectrode Set: Detection of Biomolecules to Heavy Metals

An ultrasensitive electrochemical microelectrode set (μ-ES), where all three electrodes are made of highly densified carbon nanotube fiber (HD-CNTf) cross sections (length ∼40 μm), embedded in an inert polymer matrix, and exposed open-ended CNTs at the interface, is presented here. Bare open ends of HD-CNTf rods were used as the working (∼40 μm diameter) and counter (∼94 μm diameter) electrodes, while the cross section of a ∼94 μm diameter was electroplated with Ag/AgCl and coated with Nafion to employ as a quasi-reference electrode. The Ag/AgCl/Nafion-coated HD-CNTf rod quasi-reference electrode provided a very stable potential comparable to the commercial porous-junction Ag/AgCl reference electrode. The HD-CNTf rod μ-ES has been evaluated by electrochemical determination of biologically important analytes, i.e., dopamine (DA), β-nicotinamide adenine dinucleotide (NADH), a diuretic drug, i.e., furosemide, and a heavy metal, i.e., lead ions (Pb²⁺). Different voltammetric techniques were employed during the study, i.e., cyclic voltammetry (CV), square wave voltammetry (SWV), amperometry, and square wave anodic stripping voltammetry (SWASV). The direct metallic connection to CNTs gives access to the exceptional properties of highly ordered open-ended CNTs as electrochemical sensors. The distinct structural and electronic properties of aligned HD-CNTf rods in the μ-ES demonstrate fast electron transfer kinetics and offer excellent detection performance during testing for different analytes with wide linear ranges, excellent sensitivity, and very low limits of detection.

Electrochemical Determination of Lead Using A Composite Sensor Obtained from Low-Cost Green Materials:Graphite/Cork

The purpose of this study was to develop an inexpensive, simple, and highly selective cork-modified carbon paste electrode for the determination of Pb(II) by differential pulse anodic stripping voltammetry (DPASV) and square-wave anodic stripping voltammetry (SWASV). Among the cork–graphite electrodes investigated, the one containing 70% w/w carbon showed the highest sensitivity for the determination of Pb(II) in aqueous solutions. Under SWASV conditions, its linear range and relative standard deviation are equal to 1–25 µM and 1.4%, respectively; the limit of detection complies with the value recommended by the World Health Organization. To optimize the operating conditions, the selectivity and accuracy of the analysis were further investigated by SWASV in acidic media. Finally, the electrode was successfully applied for the determination of Pb(II) in natural water samples, proving to be a sensitive electrochemical sensor that meets the stringent environmental control requirements.

Parts per trillion detection of heavy metals in as-is tap water using carbon nanotube microelectrodes

Heavy metal contamination of drinking water is a major global issue. Research reports across the globe show contamination of heavy metals higher than the set standards of the World Health Organization (WHO) and US Environmental Protection Agency (EPA). To our knowledge, no electrochemical sensor for heavy metals with parts per trillion (PPT) limits of detection (LOD) in as-is tap water has been reported or developed. Here, we report a microelectrode that consists of six highly densified carbon nanotube fiber (HD-CNTf) cross sections called rods (diameter ∼69 μm and length ∼40 μm) in a single platform for the ultra-sensitive detection of heavy metals in tap water and simulated drinking water. The HD-CNTf rods microelectrode was evaluated for the individual and simultaneous determination of trace level of heavy metal ions i.e. Cu²⁺, Pb²⁺ and Cd²⁺ in Cincinnati tap water (without supporting electrolyte) and simulated drinking water using square wave stripping voltammetry (SWSV). The microsensor exhibited a broad linear detection range with an excellent limit of detection for individual Cu²⁺, Pb²⁺ and Cd²⁺ of 6.0 nM, (376 ppt), 0.45 nM (92 ppt) and 0.24 nM (27 ppt) in tap water and 0.32 nM (20 ppt), 0.26 nM (55 ppt) and 0.25 nM (28 ppt) in simulated drinking water, respectively. The microelectrode was shown to detect Pb²⁺ ions well below the WHO and EPA limits in a broad range of water quality conditions reported for temperature and conductivity in the range of 5 °C-45 °C and 55 to 600 μS/cm, respectively.