Electrochemiluminescence Enhanced by the Synergetic Effect of Porphyrin and Multi‐walled Carbon Nanotubes for Uric Acid Detection

Molecularly imprinted electrochemiluminescence sensor based on luminol functionalized Co-MOF for rifampicin detection

A highly sensitive molecularly imprinted electrochemiluminescence (MIECL) sensor was developed for detecting rifampicin (RIF) based on luminol@Co-MOF. Co-MOF had a significant enhancement of ECL signaling in the luminol-O2 system. Molecular imprinted polymers (MIPs) with the introduction of RIF provide new properties for the specific recognition of RIF. A noteworthy decrease in ECL intensity was observed with higher concentrations of RIF. Consequently, the ECL signal was controlled by RIF elution from and adsorption by the MIP, thus establishing a new method for RIF detection. Under optimal conditions, this sensor exhibited linear detection ranges of RIF between 1.0 × 10-11 mol L-1 and 1.0 × 10-6 mol L-1, with a detection limit of 3.3 × 10-12 mol L-1 (S/N = 3). The recoveries ranged between 98.1 and 106.0% in fish samples. This method can be used as a sensitive and rapid method to detect RIF in real samples.

Optimization and miniaturization of SE-ECL for potential-resolved, multi-color, multi-analyte detection

Electrochemiluminescence (ECL) is a bioanalytical technique with numerous advantages, including the potential for high temporal and spatial resolution, a high signal-to-noise ratio, a broad dynamic range, and rapid measurement capabilities. To reduce the complexity of a multi-electrode approach, we use a single-electrode electrochemiluminescence (SE-ECL) configuration to achieve the simultaneous emission and detection of multiple colors for applications that require multiplexed detection of several analytes. This method exploits intrinsic differences in the electric potential applied along single electrodes built into electrochemical cells, enabling the achievement of distinct colors through selective excitation of ECL luminophores. We present results on the optimization of SE-ECL intensity for different channel lengths and widths, with sum intensities being 5 times larger for 6 cm vs. 2 cm channels and linearly increasing with the width of the channels. Furthermore, we demonstrated for the first time that applying Alternating Current (AC) voltage within the single electrode setup for driving the ECL reactions has a dramatic effect on the emitted light intensity, with square waveforms resulting in higher intensities vs sine waveforms. Additionally, multiplexed multicolor SE-ECL on a 6.5 mm × 3.6 mm CMOS semiconductor image sensor was demonstrated for the first time, with the ability to simultaneously distinguish four different colors, leading to the ability to measure multiple analytes.

Enzymatic and Non-Enzymatic Uric Acid Electrochemical Biosensors: A Review

In recent years, the development of electrochemical biosensors for uric acid has made great achievements. Firstly, uric acid electrochemical biosensors were classified according to their reaction mechanism. Then, the reaction mechanism of the uric acid sensor and the application of nano-modified materials were deeply analyzed from the perspective of non-enzyme and enzymes. In this paper, the catalytic oxidation capacity, enzyme adsorption effect, conductivity, robustness, detection range, and detection limit of uric acid sensors were discussed and compared. Finally, the advantages of acid-sensitive electrochemical biosensors were summarized, and the constructive recommendations were proposed for improving the deficiencies of acid biosensors. The potential for further development in this area was also discussed.

Porphyrin Functionalized Carbon Quantum Dots for Enhanced Electrochemiluminescence and Sensitive Detection of Cu2

Porphyrin (TMPyP) functionalized carbon quantum dots (CQDs-TMPyP), a novel and efficient carbon nanocomposite material, were developed as a novel luminescent material, which could be very useful for the sensitive detection of copper ions in the Cu²⁺ quenching luminescence of functionalized carbon quantum dots. Therefore, we constructed a sensitive "signal off" ECL biosensor for the detection of Cu²⁺. This sensor can sensitively respond to copper ions in the range of 10 nM to 10 μM, and the detection limit is 2.78 nM. At the same time, it has good selectivity and stability and a benign response in complex systems. With excellent properties, this proposed ECL biosensor provides an efficient and ultrasensitive method for Cu²⁺ detection.

SE-ECL on CMOS: a miniaturized electrochemiluminescence biosensor

Biosensors exhibit high potential for the detection of analytes of interest at the point-of-need. Over the past two decades, the combination of novel biosensing systems - such as electrochemiluminescence (ECL) biosensors - and advances in microfluidic techniques has allowed the development of lab-on-a-chip devices with enhanced overall performance and simplified sample handling. However, recording data with conventional platforms requires advanced and complicated instruments, such as sensitive photodetectors coupled to microscopes, to capture the photons from the chemiluminescent reaction. In this work, we integrated microfluidic and luminol/hydrogen peroxide ECL systems on a complementary metal-oxide-semiconductor (CMOS) chip for sample handling and data collection on the same platform. This was achieved by the adaptation of a single electrode as an electrochemical transducer and a CMOS chip as a built-in detector. We demonstrated the application of this platform for the detection of uric acid (UA), a biomarker of gout disease. A linear detection range was observed from 25 to 300 μM, with a detection limit (LOD) as low as 26.09 μM. The device showed high reusability and reproducibility within the linear detection range while maintaining high selectivity for UA detection. The analytical performance has also been evaluated in simulated saliva and urine samples, demonstrating the potential utility in medical diagnosis at the point-of-need. Compared to other ECL imaging platforms, this device showed an eightfold increase in photon collection efficiency. Overall, this approach has promising potential as an inexpensive, portable, and efficient ECL platform for measuring analytes at the point-of-need.