A simple sample pretreatment device with supported liquid membrane for direct injection of untreated body fluids and in-line coupling to a commercial CE instrument

Progress in on-line, at-line, and in-line coupling of sample treatment with capillary and microchip electrophoresis over the past 10 years: A review

The review presents an evaluation of the development of on-line, at-line and in-line sample treatment coupled with capillary and microchip electrophoresis over the last 10 years. In the first part, it describes different types of flow-gating interfaces (FGI) such as cross-FGI, coaxial-FGI, sheet-flow-FGI, and air-assisted-FGI and their fabrication using molding into polydimethylsiloxane and commercially available fittings. The second part deals with the coupling of capillary and microchip electrophoresis with microdialysis, solid-phase, liquid-phase, and membrane based extraction techniques. It mainly focuses on modern techniques such as extraction across supported liquid membrane, electroextraction, single drop microextraction, head space microextraction, and microdialysis with high spatial and temporal resolution. Finally, the design of sequential electrophoretic analysers and fabrication of SPE microcartridges with monolithic and molecularly imprinted polymeric sorbents are discussed. Applications include the monitoring of metabolites, neurotransmitters, peptides and proteins in body fluids and tissues to study processes in living organisms, as well as the monitoring of nutrients, minerals and waste compounds in food, natural and wastewater.

Integration of three-phase microelectroextraction sample preparation into capillary electrophoresis

A major strength of capillary electrophoresis (CE) is its ability to inject small sample volumes. However, there is a great mismatch between injection volume (typically <100 nL) and sample volumes (typically 20-1500 µL). Electromigration-based sample preparation methods are based on similar principles as CE. The combination of these methods with capillary electrophoresis could tackle obstacles in the analysis of dilute samples. This study demonstrates coupling of three-phase microelectroextraction (3PEE) to CE for sample preparation and preconcentration of large volume samples while requiring minimal adaptation of CE equipment. In this set-up, electroextraction takes place from an aqueous phase, through an organic filter phase, into an aqueous droplet that is hanging at the capillary inlet. The first visual proof-of-concept for this set-up showed successful extraction using the cationic dye crystal violet (CV). The potential of 3PEE for bioanalysis was demonstrated by successful extraction of the biogenic amines serotonin (5-HT), tyrosine (Tyr) and tryptophan (Trp). Under optimized conditions limits of detection (LOD) were 15 nM and 33 nM for 5-HT and Tyr respectively (with Trp as an internal standard). These LODs are comparable to other similar preconcentration methods that have been reported in conjunction with CE. Good linearity (R² > 0.9967) was observed for both model analytes. RSDs for peak areas in technical replicates, interday and intraday variability were all satisfactory, i.e., below 14%. 5-HT, Tyr and Trp spiked to human urine were successfully extracted and separated. These results underline the great potential of 3PEE as an integrated enrichment technique from biological samples and subsequent sensitive metabolomics analysis.

Novel and simple headspace in-tube microextraction coupled with capillary electrophoresis

In liquid phase microextraction, high enrichment factors can be obtained using an acceptor phase of small volume. By hanging an acceptor drop at the separation capillary tip, single drop microextraction (SDME) can be in-line coupled with capillary electrophoresis (CE). The small surface-to-volume ratio of the drop enables high enrichment factors to be obtained in a short time. One practical issue in SDME is how to keep the drop attached to the capillary stable. Here, we present novel but extremely simple in-tube microextraction (ITME) using the liquid inside the capillary as an acceptor phase, without forming a drop at the capillary tip. As a first example, ITME has been combined with headspace (HS) extraction. Simply by placing a capillary filled with a basic run buffer in the HS above an acidic donor solution, volatile acidic analytes were extracted into the acceptor phase in the capillary. After extraction, electrophoresis of the extracts in the capillary was carried out. Owing to the robust nature of the acceptor phase, the extraction temperature and time ranges of HS-ITME can be extended significantly, compared to HS-SDME. The enrichment factors for chlorophenols in a standard solution were up to 1100 under an optimal HS-ITME condition of 80°C for 15min and the limits of detections (LODs) obtained by monitoring the absorbance at 214nm were about 4nM. The whole procedures of HS-ITME-CE were carried out automatically using built-in programs of a commercial CE instrument.

Recent developments in capillary and microchip electroseparations of peptides (2011-2013)

The review presents a comprehensive survey of recent developments and applications of capillary and microchip electroseparation methods (zone electrophoresis, ITP, IEF, affinity electrophoresis, EKC, and electrochromatography) for analysis, isolation, purification, and physicochemical and biochemical characterization of peptides. Advances in the investigation of electromigration properties of peptides, in the methodology of their analysis, including sample preseparation, preconcentration and derivatization, adsorption suppression and EOF control, as well as in detection of peptides, are presented. New developments in particular CE and CEC modes are reported and several types of their applications to peptide analysis are described: conventional qualitative and quantitative analysis, determination in complex (bio)matrices, monitoring of chemical and enzymatical reactions and physical changes, amino acid, sequence and chiral analysis, and peptide mapping of proteins. Some micropreparative peptide separations are shown and capabilities of CE and CEC techniques to provide relevant physicochemical characteristics of peptides are demonstrated.