Lab-on-a-chip biophotonics: its application to assisted reproductive technologies

Hitting the wall: Human sperm velocity recovery under ultra-confined conditions

Infertility is a common medical condition encountered by health systems throughout the world. Despite the development of complex in vitro fertilization techniques, only one-third of these procedures are successful. New lab-on-a-chip systems that focus on spermatozoa selection require a better understanding of sperm behavior under ultra-confined conditions in order to improve outcomes. Experimental studies combined with models and simulations allow the evaluation of the efficiency of different lab-on-a-chip devices during the design process. In this work, we provide experimental evidence of the dynamics of sperm interacting with a lateral wall in a shallow chamber. We observe a decrease in average sperm velocity during initial wall interaction and partial recovery after the alignment of the trajectory of the cell. To describe this phenomenon, we propose a simple model for the sperm alignment process with a single free parameter. By incorporating experimental motility characterization into the model, we achieve an accurate description of the average velocity behavior of the sperm population close to walls. These results will contribute to the design of more efficient lab-on-a-chip devices for the treatment of human infertility.

A new calibration concept for a reproducible quantitative detection based on SERS measurements in a microfluidic device demonstrated on the model analyte adenine

This study demonstrates a new concept of calibrating surface enhanced Raman scattering (SERS) intensities without using additional substances as an internal standard and explores factors such as laser fluctuation and different Ag substrates, which affect the results of quantitative analyses based on SERS. To demonstrate the capabilities of the concept, the model analyte adenine has been chosen. A lab-on-a-chip device is applied for the measurements to guarantee consistent data recording. In order to simulate varied measuring conditions, two varying silver colloids (batch 1 and 2) are utilized as a SERS substrate and two different laser power levels (25 or 55 mW) are applied on the sample. A concentration gradient was generated which allows the use of the analyte itself for the correction of the resulting SERS spectra regarding intensity deviations caused by different ambient conditions. In doing so, a vast improvement in the quantification using SERS, especially in view of the comparability, reproducibility and repeatability, is demonstrated.

Cooperative roles of biological flow and surface topography in guiding sperm migration revealed by a microfluidic model

Successful reproduction in mammals requires sperm to swim against a fluid flow and through the long and complex female reproductive tract before reaching the egg in the oviduct. Millions of them do not make it. Despite their clinical importance, the roles played in sperm migration by the diverse biophysical and biochemical microenvironments within the reproductive tract are largely unknown. In this article, we present the development of a double layer microfluidic device that recreates two important biophysical environments within the female reproductive tract: fluid flow and surface topography. The unique feature of the device is that it enables one to study the cooperative roles of fluid flow and surface topography in guiding sperm migration. Using bull sperm as a model system, we found that microfluidic grooves embedded on a channel surface facilitate sperm migration against fluid flow. These findings suggest ways to design in vitro fertilization devices to treat infertility and to develop non-invasive contraceptives that use a microarchitectural design to entrap sperm.

Easy daylight fabricated hydrogel array for colorimetric DNA analysis

The fabrication of 3D hydrogel microarrays for DNA analytics that allow simple visual signal readout for on-site applications is described. A convenient one-step polymerization of the hydrogel including in situ capture oligonucleotide immobilization is accomplished by using N,N'-dimethylacrylamide/polyethylene glycol (PEG1900 )-bisacrylamide monomers. The implementation of an acylphosphine-oxide photoinitiator even allows polymerization at daylight, whereas other approaches require exposure with light in the UV-range. This minimizes the risk of UV-caused DNA damages within the capture DNA-strand that could adversely affect the subsequent hybridization step. The porous network of these gel segments allows DNA as well as protein penetration. Thus, the successful in-gel DNA hybridization is monitored by the deposition of silver nanoparticles. These metal particles allow naked eye signal readout.

Thinking big by thinking small: application of microfluidic technology to improve ART

In Vitro Fertilization (IVF) laboratories often carry a penchant to resist change while in the pursuit of maintaining consistency in laboratory conditions. However, implementation of new technology is often critical to expand scientific discoveries and to improve upon prior successes to advance the field. Microfluidic platforms represent a technology that has the potential to revolutionize the fundamental processes of IVF. While the focus of microfluidic application in IVF has centered on embryo culture, the innovative platforms carry tremendous potential to improve other procedural steps and represents a possible paradigm shift in how we handle gametes and embryos. The following review will highlight application of various microfluidic platforms in IVF for use in maturation, manipulation, culture, cryopreservation and non-invasive quality assessment; pointing out new insights gained into functions of sperm, oocytes and embryos. Platform design and function will also be discussed, focusing on limitations, advancements and future refinements that can further aid in their clinical implementation.