Interferometric optical fiber sensor for optoacoustic endomicroscopy

Advanced fabrication of polymer waveguide interferometric sensor utilizing interconnected holey fibers

A universally applicable approach is proposed for the fabrication of fiber-optic polymer sensors. The hollow-core fibers (HCFs) with inner diameters of 30 µm, 50 µm, and 75 µm are spliced coaxially with dual-hole fiber (DHF) or photonic crystal fiber (PCF). Owing to the sized-matched air holes within HCF and DHF/PCF, an interconnected in-fiber microchannel is constructed, which facilitates rapid and complete filling of the HCF's central hole with liquid glue. After the ultraviolet-induced polymerization, a polymer Fabry-Perot interferometer is achieved by cutting the HCF end with a desired cavity length. Besides, the interference visibility is significantly enhanced by adding a refractive-index-modulated polymer cap onto the cutting surface. Experimental results demonstrate the optimized interference spectra and the interconnection of the matched air-hole fibers. The polymer sensor exhibits a signal-to-noise ratio of 56.8 dB for detecting pulsed ultrasonic waves, which is more than twice that of a partially polymer-filled sensor. Due to the hermetically-sealed structure, the sensor probe presents constrained performance with a temperature sensitivity of 230.2 pm/°C and a humidity sensitivity of 93.7 pm/%RH, which can be further improved by releasing the polymer waveguide from fiber cladding. Based on interconnected holey fibers, the proposed approach has a uniform size-controlled polymer waveguide dimension with increased spectrum visibility, rendering it suitable for a diverse range of microstructure-matched optical fibers.

Single optical fiber based forward-viewing all-optical ultrasound self-transceiving probe

All-optical ultrasound probes with fully integrated ultrasound generation and detection functions demonstrate some unique advantages over traditional electroacoustic counterparts. However, due to the lack of an effective solution, the most commonly used method is to assemble two separate functional optical fibers together for ultrasound generation and detection, respectively. In this Letter, an innovative strategy, to the best of our knowledge, is developed to integrate the photoacoustic effect based ultrasound generation and the Fabry-Pérot (FP) interference based ultrasound detection structures together at the end of a single double clad optical fiber (DCF), so as to make a compact forward-viewing ultrasound self-transceiving probe (1-mm diameter). From the experiment results, the as-fabricated probe can generate an ultrasound signal with an amplitude of 2.36 MPa at 2.25 mm in the transmitting mode, and its peak frequency and -6-dB bandwidth are measured to be 10.64 MHz and 22.93 MHz, respectively. When being operated under the receiving mode, the probe has a detection sensitivity of 208.4 mV/MPa for ultrasound signals with the peak frequency of 8.24 MHz, and the noise equivalent pressure (NEP) is 76.8 kPa. In addition, the forward-viewing format ultrasound self-transceiving experiment is also performed and the pulse-echo signal varying with the transmission distance is successfully captured for the first time.

High-resolution sub-millimetre diameter side-viewing all-optical ultrasound transducer based on a single dual-clad optical fibre

All-optical ultrasound (OpUS), where ultrasound is both generated and received using light, has emerged as a modality well-suited to highly miniaturised applications. In this work we present a proof-of-concept OpUS transducer built onto a single optical fibre with a highly miniaturised lateral dimension (<0.8 mm). A key innovation was to use a dual-clad optical fibre (DCF) to provide multimode light for ultrasound generation and single mode light for ultrasound reception. The transducer comprised a proximal section of DCF spliced to a short section of single mode fibre (SMF). Multimode light was outcoupled at the splice joint and guided within a square capillary to provide excitation for ultrasound generation. Whilst single mode light was guided to the distal tip of the SMF to a plano-concave microresonator for ultrasound reception. The device was capable of generating ultrasound with pressures >0.4 MPa and a corresponding bandwidth >27 MHz. Concurrent ultrasound generation and reception from the transducer enabled imaging via motorised pull-back allowing image acquisition times of 4 s for an aperture of 20 mm. Image resolution was as low as ~50 µm and 190 µm in the axial and lateral extents, respectively, without the need for image reconstruction. Porcine aorta was imaged ex vivo demonstrating detailed ultrasound images. The unprecedented level of miniaturisation along with the high image quality produced by this device represents a radical new paradigm for minimally invasive imaging.

Fabrication and Qualitative Analysis of an Optical Fibre EFPI-Based Temperature Sensor

The following presents a comparison of an extrinsic Fabry–Perot interferometer (EFPI)-based temperature sensor, constructed using a novel diaphragm manufacturing technique, with a reference all-glass EFPI temperature sensor. The novel diaphragm was manufactured using polyvinyl alcohol (PVA). The novel sensor fabrication involved fusing a single-mode fibre (SMF) to a length of fused quartz capillary, which has an inner diameter of 132 μm and a 220 μm outer diameter. The capillary was subsequently polished until the distal face of the capillary extended approximately 60 μm beyond that of the single mode fibre. Upon completion of polishing, the assembly is immersed in a solution of PVA. Controlled extraction resulted in creation of a thin diaphragm while simultaneously applying a protective coating to the fusion point of the SMF and capillary. The EFPI sensor is subsequently sealed in a second fluid-filled capillary, thereby creating a novel temperature sensor structure. Both temperature sensors were placed in a thermogravimetric analyser and heated from an indicated 30 °C to 100 °C to qualitatively compare sensitivities. Initial results indicated that the novel manufacturing technique both expedited production and produces a more sensitive sensor when compared to an all-glass construction.