Thermal property and processability of elastomeric polymer alloy composed of segmented polyurethane and phospholipid polymer

Cell membrane-mimicking coating for blood-contacting polyurethanes

The aim of the present work was to develop simple modification technique for polyurethanes (PUs) intended for use in blood-contacting implants (vascular grafts, heart prosthesis, ventricular assist devices). PU surface was modified with soybean-derived phosphatidylcholine (PC) via one-step dip coating technique. In order to evaluate blood compatibility of the obtained materials, samples were contacted with human blood under static and arterial flow-simulated conditions. The PC-modified surfaces were thoroughly characterized and tested for fibrinogen resistance, the ability to resist platelet adhesion and activation, hemolysis percentage and plasma recalcification time. Results demonstrated significant, more than three-fold reduction in the amount of fibrinogen adsorbed to PC-modified materials as compared to non-modified PU. Analysis of the samples’ surface after incubation with blood showed high reduction in platelet adhesion. The results were confirmed by analysis of blood samples collected after shear-stress tests – the percentage of free (non-aggregated) platelets remaining in blood samples contacted with PC-coated materials exceeded 70%. The same parameter measured for non-modified PU was significantly lower and equaled 28%.

Cellulose acetate hollow fiber membranes blended with phospholipid polymer and their performance for hemopurification

Commercially available hollow fiber membranes (HFMs) made from synthetic polymers, including cellulose acetate (CA) HFMs, used as hemopurification membranes, need to improve in hemocompatibility, by suppressing protein adsorption and clot formation. In this study, CA HFMs blended with 2-methacryloyloxyethyl phosphorylcholine (MPC) copolymer (PMB30 composed of MPC and n-butyl methacrylate (BMA)) were prepared by a dry-jet wet spinning process. Their performances were evaluated by characterizing their properties such as structure, permeability and protein adsorption. CA/PMB30-blend HFMs showed structure changes such as increase of porosity, development of large pores and decreasing of the thickness of the active layer. And the structure and permeability of CA/PMB30-blend HFMs were controllable by changing preparation conditions. Also, the CA/PMB30-blend HFMs had good permeability, low protein adsorption and low fouling property during the permeability experiment in comparison with CA HFMs, because the hydrophilic and hemocompatible MPC copolymer (PMB30) existed on the surface of the HFM.

2006 Frank Stinchfield Award: grafting of biocompatible polymer for longevity of artificial hip joints

Aseptic loosening induced by wear particles from the polyethylene liner is likely the most common cause of long-term total hip arthroplasty failure. We developed a novel hip polyethylene liner with the surface graft of a biocompatible phospholipid polymer, 2-methacryloyloxyethyl phosphorylcholine (MPC), and previously reported the grafting decreased the short-term production of wear particles and the subsequent bone resorptive responses. For clinical application, we investigated the stability of the 2-methacryloyloxyethyl phosphorylcholine grafting during sterilization and the wear resistance of the sterilized liner during longer loading comparable to clinical usage. Radiographic spectroscopy confirmed the stability of the 2-methacryloyloxyethyl phosphorylcholine polymer on the liner surface after the gamma irradiation. We used a hip wear simulator up to 1 x 10(7) cycles to test sterilized cross-linked polyethylene liners with and without 2-methacryloyloxyethyl phosphorylcholine grafting. The 2-methacryloyloxyethyl phosphorylcholine grafting markedly decreased the friction, the production of wear particles, and the wear of the liner surface. These data suggest a marked improvement in the wear resistance of the polyethylene liner by the 2-methacryloyloxyethyl phosphorylcholine grafting for clinically relevant periods after sterilization, indicating 2-methacryloyloxyethyl phosphorylcholine grafting is a promising technology for extending longevity of artificial hips.

Stress response of adherent cells on a polymer blend surface composed of a segmented polyurethane and MPC copolymers

To better understand the effect of 2-methacryloyloxyethyl phosphorylcholine (MPC) copolymer in improving the biocompatibility of segmented polyurethane (SPU), the expression of heat shock protein (HSP) mRNA in HeLa S3 cells adhered on SPU blended with MPC copolymers was measured. Conventionally, MPC copolymers (PMEH) were synthesized by changing the feed ratios of MPC and 2-ethylhexyl methacrylate. X-ray photoelectron spectroscopic analysis of the SPU/PMEH film indicated that the surface concentration of MPC units on the SPU/PMEH film increased with an increase in PMEH composition. HeLa S3 cells were cultured on SPU/PMEH films. The number of adherent cells on the SPU/PMEH films decreased with an increase in the concentration of PMEH. When the PMEH composition was greater than 0.5 wt %, cell adhesion and proliferation decreased markedly. Expressions of HSP27 and HSP47 mRNA were detected using the reverse transcription-polymerase chain reaction (RT-PCR). After incubation for 24 h, both the HSP mRNA expressions in the HeLa S3 cells showed no significant differences among all samples. In HeLa S3 cells that adhered to the SPU film for 48 h, the expressions of HSP27 and HSP47 mRNA increased significantly when compared with those incubated for 24 h. In contrast, the two kinds of mRNA expressions decreased in the HeLa S3 cells that adhered to the SPU/PMEH films for 48 h. From these results, we concluded that PMEH was quite important in suppressing the stress response of adherent HeLa S3 cells. Therefore, SPU/PMEH blend polymers are useful as implantable biomedical materials.

Surface modification of polyacrylonitrile-based membranes by chemical reactions to generate phospholipid moieties

A novel approach for the surface modification of poly(acrylonitrile-co-2-hydroxyethyl methacrylate) (PANCHEMA) membranes by introducing phospholipid moieties is presented, which involved the reaction of the hydroxyl groups on the membrane surface with 2-chloro-2-oxo-1,3,2-dioxaphospholane (COP) followed by the ring-opening reaction of COP with trimethylamine. The chemical changes of phospholipid-modified acrylonitrile-based copolymers (PMANCP) membranes were characterized by Fourier transfer infrared spectroscopy and X-ray photoelectron spectroscopy. The surface properties of PMANCP membranes were evaluated by pure water contact angle, protein adsorption, and platelet adhesion measurements. Pure water contact angles measured by the sessile drop method on PMANCP membranes were obviously lower than those measured on the PANCHEMA membranes and decreased with the increase of the content of phospholipid moieties on the membrane surface. It was found that the bovine serum albumin adsorption and platelet adhesion were suppressed significantly with the introduction of phospholipid moieties on the membranes surface. These results demonstrated that the described process was an efficient way to improve the surface biocompatibility for the acrylonitrile-based copolymer membrane.