Influence of silanated filler content on the biodegradation of bisGMA/TEGDMA dental composite resins

Synergistic effects of bacteria, enzymes, and cyclic mechanical stresses on the bond strength of composite restorations

Predicting how tooth and dental material bonds perform in the mouth requires a deep understanding of degrading factors. Yet, this understanding is incomplete, leading to significant uncertainties in designing and evaluating new dental adhesives. The durability of dental bonding interfaces in the oral microenvironment is compromised by bacterial acids, salivary enzymes, and masticatory fatigue. These factors degrade the bond between dental resins and tooth surfaces, making the strength of these bonds difficult to predict. Traditionally studied separately, a combined kinetic analysis of these interactions could enhance our understanding and improvement of dental adhesive durability. To address this issue, we developed and validated an original model to evaluate the bond strength of dental restorations using realistic environments that consider the different mechanical, chemical, and biological degradative challenges working simultaneously: bacteria, salivary esterases, and cyclic loading. We herein describe a comprehensive investigation on dissociating the factors that degrade the bond strength of dental restorations. Our results showed that cariogenic bacteria are the number one factor contributing to the degradation of the bonded interface, followed by cyclic loading and salivary esterases. When tested in combinatorial mode, negative and positive synergies towards the degradation of the interface were observed. Masticatory loads (i.e., cycling loading) enhanced the lactic acid bacterial production and the area occupied by the biofilm at the bonding interface, resulting in more damage at the interface and a reduction of 73 % in bond strength compared to no-degraded samples. Salivary enzymes also produced bond degradation caused by changes in the chemical composition of the resin/adhesive. However, the degradation rates are slowed compared to the bacteria and cyclic loading. These results demonstrate that our synergetic model could guide the design of new dental adhesives for biological applications without laborious trial-and-error experimentation.

Kinetic of Light Transmission during Setting and Aging of Modern Flowable Bulk-Fill Composites

The current development of dental materials aims to improve their properties and expand their clinical application. New flowable bulk-fill composites have been released which, unlike what was previously common in this material category, are intended to be used alone and without a top layer, in various cavities. The study compares their kinetic of light transmission during monomer-to-polymer conversion on a laboratory-grade spectrometer, as well as their elastoplastic and aging behavior under simulated clinical conditions. Major differences in the kinetic of light transmission was observed, which is related to the degree of mismatch between the refractive indices of filler and polymer matrix during polymerization and/or the type of initiator used. Compared to the literature data, the kinetic of light transmission do not always correlate with the kinetic of functional group conversion, and therefore should not be used to assess polymerization quality or to determine an appropriate exposure time. Furthermore, the initial mechanical properties are directly related to the volumetric amount of filler, but degradation during aging must be considered as a multifactorial event.

Evaluation of the amount of residual monomer released from different flowable composite resins

Today, resin materials are used in the restoration of permanent and deciduous teeth or as fissure sealants. The materials can contain different types of monomers (Bis-GMA, UDMA, TEGDMA). These monomers can be released into the oral cavity after polymerization. Residual monomers released from resin-containing restorative materials after polymerization have been reported to have negative effects on mechanical properties. The aim of our study is to evaluate the amount of residual monomers released after polymerization of different flowable composite resin materials using two different modes of LED light source. Composite disc samples (8 mm diameter/2 mm depth) prepared for each material group were polymerized using two different modes of the LED light device (Standard mode and extra power mode). HPLC (High Performance Liquid Chromatography) device was used to measure the amount of residual monomer release at 1 h, 1 day, 3 days and 7 days periods. Pairwise comparison of the differences between the materials was performed by Post-hoc test. For each residual monomer, the Kruskal Wallis test was used to analyze the difference between the materials in standard mode and the difference between the materials in extra power mode. According to the results of the study; Grandio flow flowable composite showed the highest release of TEGDMA and Bis-GMA while SDR® Flow flowable composite showed the lowest release of TEGDMA, Bis-GMA and UDMA. For all materials, the extra power mode resulted in more residual monomer release. TEGDMA and Bis-GMA release was detected in all tested flowable composites at all time periods.

Biodegradation of Urethane Dimethacrylate-based materials (CAD/CAM resin-ceramic composites) and its effect on the adhesion and proliferation of Streptococcus mutans

OBJECTIVE

To investigate whether urethane dimethacrylate (UDMA) -based dental restorative materials biodegrade in the presence of Streptococcus mutans (S. mutans) and whether the monomers affect the adhesion and proliferation of S. mutans in turn.

METHODS

Cholesterol esterase and pseudocholinesterase-like activities in S. mutans were detected using p-nitrophenyl substrate. Two UDMA-based CAD/CAM resin-ceramic composites, Lava Ultimate (LU) and Vita Enamic (VE), and a light-cured UDMA resin block were co-cultured with S. mutans for 14 days. Their surfaces were characterized by scanning electron microscopy and laser microscopy, and the byproducts of biodegradation were examined by Ultra Performance Liquid Chromatography-Tandem Mass Spectrometry (UPLC-MS/MS). Then, the antimicrobial components (silver nanoparticles with quaternary ammonium salts) were added to the UDMA resin block to detect whether the biodegradation was restrained. Finally, the effect of UDMA on biofilm formation and virulence expression of S. mutans was assessed.

RESULTS

Following a 14-day immersion, the LU and UDMA resin blocks' surface roughness increased. The LU and VE groups had no UDMA or its byproducts discovered, according to the UPLC-MS/MS data, whereas the light-cured UDMA block group had UDMA, urethane methacrylate (UMA), and urethane detected. The addition of antimicrobial agents showed a significant reduction in the release of UDMA. Biofilm staining experiments showed that UDMA promoted the growth of S. mutans biofilm and quantitative real-time polymerase chain reaction results indicated that 50 μg/mL UDMA significantly increase the expression of gtfB, comC, comD, comE, and gbpB genes within the biofilm.

CONCLUSIONS

UDMA in the light-cured resin can be biodegraded to produce UMA and urethane under the influence of S. mutans. The formation of early biofilm can be promoted and the expression of cariogenic genes can be up-regulated by UDMA.

CLINICAL SIGNIFICANCE

This study focuses for the first time on whether UDMA-based materials can undergo biodegradation and verifies from a genetic perspective that UDMA can promote the formation of S. mutans biofilms, providing a reference for the rational use of UDMA-based materials in clinical practice.

Effective luting agents for glass-fiber posts: A network meta-analysis

OBJECTIVES

The aims of this study were to systematically review the literature and compare the relative effects of various luting agents on bonding between glass-fiber posts and root canal dentin in short- and long-term aging conditions.

DATA/SOURCES

The literature was electronically searched in PubMed, Embase, and Scopus. A manual search was performed by scanning the reference lists of the included studies.

STUDY SELECTION

Two reviewers independently conducted the selection of studies, data extraction, and risk of bias assessment. Pairwise meta-analyses were based on random effect models. Network meta-analyses were conducted within a frequentist framework with a multivariable random effects approach. The standardized mean difference and 95% confidence interval was calculated.

RESULTS

One hundred and eighteen studies were included and assessed the effects of five luting agents. For pairwise meta-analyses, in short-term aging conditions, a significantly higher bond strength of self-adhesive resin cement (SARC) compared to etch-and-rinse adhesive composite resin core material (ERCM) in the total, coronal, and middle regions. In long-term aging conditions, a significantly higher bond strength of ERCM compared to etch-and-rinse adhesive resin cement (ERRC) in all regions. Furthermore, SARC showed a significantly higher bond strength compared to self-etch adhesive composite resin core material (SECM) in the total, middle, and apical regions. For network meta-analyses, in the apical region, a significantly higher bond strength of SARC compared to ERRC in both aging conditions.

CONCLUSIONS

The SARC tended to be the most effective luting agent in bonding between glass-fiber posts and root canal dentin in short- and long-term aging conditions.

Shade, Aging and Spatial-Dependent Variation of Elastoplastic and Viscoelastic Characteristics in a Dental, Submicron Hybrid CAD/CAM Composite

This article reports the elastoplastic and viscoelastic response of an industrially cured CAD/CAM resin-based composite (Brilliant Crios, Coltene) at different scales, spatial locations, aging conditions, and shading. Mechanical tests were performed at the macroscopic scale to investigate material strength, elastic modulus, fracture mechanisms and reliability. An instrumented indentation test (IIT) was performed at the microscopic level in a quasi-static mode to assess the elastic and plastic deformation upon indentation, either by mapping transverse areas of the CAD/CAM block or at randomly selected locations. A dynamic-mechanical analysis was then carried out, in which chewing-relevant frequencies were included (0.5 to 5 Hz). Characteristics measured at the nano- and micro-scale were more discriminative in identifying the impact of variables as those measured at macro scale. Anisotropy as a function of the spatial location was identified in all shades, with gradual variation in properties from the center of the block to peripheral locations. Depending on the scale of observation, differences in shade and translucency are very small or not statistically significant. The aging effect is classified as low, but measurable on all scales, with the same pattern of variation occurring in all shades. Aging affects plastic deformation more than elastic deformation and affects elastic deformation more than viscous deformation.

Surface roughness and microhardness of enamel white spot lesions treated with different treatment methods

Objective

To analyse the surface roughness and microhardness of artificial enamel white spot lesions before and after WSL formation, after treatment (Opalsutre™ microabrasion, Sylc® bioactive glass, and ICON® resin infiltration), and after pH cycling with the help of the profilometer surface roughness tester and the digital Vickers microhardness tester.

Materials and methods

Seventy-five extracted molars were used to acquire one hundred specimens. 50 specimens were randomly assigned to five groups (n = 10) for the surface roughness study: 1) Sound group, 2) WSL group, 3) micro abrasion (MA; Opalustre, Ultradent, South Jordan, UT, USA), 4) bioactive glass 45S5 Sylc powder (Sylc; Denfotex Research Ltd, Inverkeithing, UK), and 5) ICON resin infiltration (ICON; DMG, Hamburg, Germany). An additional 25 specimens were used to obtain 50 enamel slabs for the surface microhardness study, which were also assigned to the same groups. All groups underwent a final stage of pH cycling. Surface roughness and surface microhardness measurements were performed at different stages for all groups.

Results

Regarding surface roughness, ICON significantly reduced the surface roughness compared to Opalustre and Sylc, with no significant difference between Opalustre and Sylc. In terms of surface microhardness, ICON showed the highest improvement, followed by Sylc and then Opalustre. Both surface roughness and microhardness were significantly affected by demineralization, partially improved after treatment, and then regressed significantly after pH cycling.

Conclusion

ICON resin infiltrant can be considered as a superior treatment option for improving surface roughness and microhardness, while Opalustre demonstrated relatively the poorest performance compared to the other treatment options. It is noteworthy that the pH cycling procedure had an adverse impact irrespective of the treatment option used.

Accelerated versus Slow In Vitro Aging Methods and Their Impact on Universal Chromatic, Urethane-Based Composites

Structural coloring of dental resin-based composites (RBC) is used to create universal chromatic materials designed to meet any aesthetic need, replacing the mixing and matching of multiple shades. The microstructural adjustments to create this desideratum involve nanoscale organic-inorganic core-shell structures with a particular arrangement. The generally higher polymer content associated with these structures compared to universal chromatic RBCs colored by pigments, which in their microstructure come close to regularly shaded RBCs, can influence the way the material ages. Accelerated and slow aging up to 1.2 years of immersion in artificial saliva at 37 °C were therefore compared in relation to their effects on the materials described above and in relation to the immersion conditions prescribed by standards. Quasi-static and viscoelastic parameters were assessed to quantify these effects by a depth-sensing indentation test equipped with a DMA module. The microstructure of the materials was characterized by scanning electron microscopy. The results convincingly show a differentiated influence of the aging protocol on the measured properties, which was more sensitively reflected in the viscoelastic behavior. Accelerated aging, previously associated with the clinical behavior of RBCs, shows a 2- to 10-fold greater effect compared to slow aging in artificial saliva of up to 1.2 years, highly dependent on the microstructure of the material.

Cytotoxic, Elastic-Plastic and Viscoelastic Behavior of Aged, Modern Resin-Based Dental Composites

The development of resin-based composites (RBCs) is a delicate balance of antagonistic properties with direct clinical implications. The clear trend toward reducing filler size in modern RBCs solves esthetic deficiencies but reduces mechanical properties due to lower filler content and increases susceptibility to degradation due to larger filler-matrix interface. We evaluated a range of nano- and nano-hybrid RBCs, along with materials attempting to address shrinkage stress issues by implementing an Ormocer matrix or pre-polymerized fillers, and materials aiming to provide caries-protective benefit by incorporating bioactive fillers. The cytotoxic response of human gingival fibroblast (HGF) cells after exposure to the RBC eluates, which were collected for up to six months, was analyzed using a WST-1 assay. The microstructural features were characterized using a scanning electron microscopy and were related to the macroscopic and microscopic mechanical behaviors. The elastic-plastic and viscoelastic material behaviors were evaluated at the macroscopic and microscopic levels. The data were supplemented with fractography, Weibull analysis, and aging behavioral analysis. The results indicate that all RBCs are non-cytotoxic at adequate exposure. The amount of inorganic filler affects the elastic modulus, while only to a limited extent the flexural strength, and is well below the theoretical estimates. The nanoparticles and the agglomeration of nanoparticles in the RBCs help generate good mechanical properties and excellent reliability, but they are more prone to deterioration with aging. The pre-polymerized fillers lower the initial mechanical properties but are less sensitive to aging. Only the Ormocer retains its damping ability after aging. The strength and modulus of elasticity on the one hand and the damping capacity on the other are mutually exclusive and indicate the direction in which the RBCs should be further developed.

Influence of the Polymerization Modes on the Methacrylic Acid Release from Dental Light-Cured Materials-In Vitro Study

The study focuses on the problem of lowering the pH around a composite filling concerning the polymerization modes and methacrylic acid release, which may affect not only the oral health but also the whole organism. A total of 90 specimens (30 of each: Filtek Bulk Fill, Evetric and Riva LC) were placed in 90 sterile hermetic polyethene containers with saline and incubated at 37 °C. Ten samples of each material were light-cured for 40 s with one of the three curing modes: full power mode (FPM), ramping mode (RM) and pulse mode (PM). The pH and methacrylic acid release evaluation were performed at the following time points: after 2 h and after 3, 7, 21 and 42 days from the specimen preparation. Regardless of light-curing mode, all used materials were characterized by a gradual elevation in methacrylic acid concentration. Only for Filtek Bulk Fill, increased methacrylic acid release was closely associated with lower pH. The choice of the polymerization mode has no significant influence on the methacrylic acid release. However, further research about composite light-curing is necessary to create the procedure algorithm, reducing the local and systemic complications associated with composite fillings.

Biodegradation of Dental Resin-Based Composite—A Potential Factor Affecting the Bonding Effect: A Narrative Review

In recent years, although resin composite has played an important role in the restoration of tooth defects, it still has several disadvantages, including being biodegraded by saliva, bacteria and other enzymes in the oral cavity, which may result in repair failure. This factor is not conducive to the long-term survival of the prosthesis in the mouth. In this article, we review the causes, influencing factors and prevention methods of resin biodegradation. Biodegradation is mainly caused by esterase in saliva and bacteria, which breaks the ester bond in resin and causes the release of monomers. The mechanical properties of the prosthesis can then be affected. Meanwhile, cathepsin and MMPs are activated on the bonding surface, which may decompose the dentin collagen. In addition, neutrophils and residual water on the bonding surface can also aggravate biodegradation. Currently, the primary methods to prevent biodegradation involve adding antibacterial agents to resin, inhibiting the activity of MMPs and enhancing the crosslinking of collagen fibers. All of the above indicates that in the preparation and adhesion of resin materials, attention should be paid to the influence of biodegradation to improve the prosthesis’s service life in the complex environment of the oral cavity.

Universal Chromatic Resin-Based Composites: Aging Behavior Quantified by Quasi-Static and Viscoelastic Behavior Analysis

Universal chromatic dental resin-based composites were recently developed in an attempt to speed up the restoration process with the aim of making it easier for the practitioner to decide on a suitable shade and to avoid time-consuming matching and mixing of materials. The way in which color is created in the analyzed universal chromatic materials is innovative, as it is not only induced by selective light absorption via pigments (Venus Diamond ONE, Venus Pearl ONE), as is usual in regular composites (Charisma Classic, Charisma Topaz, Venus, Venus Diamond), but also by selective light reflection via particularized microstructures (Omnichroma). Material properties were assessed at 24 h post-polymerization and after artificial aging. Flexural strength (n = 20) and modulus were measured in a 3-point-bending test and complemented with fractography and Weibull analysis. Quasi-static (Martens, Vickers, and indentation hardness; elastic and total indentation work; creep, indentation depth) and viscoelastic (storage, loss, and indentation moduli; loss factor) behavior (n = 6) was measured by a depth-sensing indentation test equipped with a DMA module. The nanoscale silica/zirconia polymer core-shell structure in the structural-colored material induces similar or poorer mechanical properties compared with pigment-colored materials, which is related to the higher polymer content. For all materials, aging shows a clear influence on the measured properties, with the degree of degradation depending on the measurement scale.

Effect of Volume and Renewal of the Storage Media on the Release of Monomer from Dental Composites

This study evaluated the effect of the volume and renewing of storage media on monomer leachability from dental composite. Samples of two dental composites (BEAUTIFIL II Gingiva (BG) and Filtek Bulk-Fill Flowable (FBF)) were stored after polymerization in 1 and 3 milt storage media (ethanol/water 75%) for seven days. Refreshing of storage media was done in half of the samples of each group. The amounts of releasing monomers (UDMA, BisGMA, TEGDMA) in storage media were measured by high-performance liquid chromatography (HPLC). Data was analyzed using two-way ANOVA and t-test (α = 0.05). Elution of TEGDMA and UDMA from both composites was significantly higher in 3 mL storage media. In groups with refreshing of storage media, BisGMA had higher amounts of release. Saturation makes the storage media volume important factor in monomer elution. Refreshing of storage media had significant effect on monomer release before the elution of 50% of total released monomer.

Characteristics of biofilm-induced degradation at resin-dentin interfaces using multiple combinations of adhesives and resins

OBJECTIVE

We aimed to evaluate morphological, mechanical and chemical characteristics at resin-dentin interfaces using multiple combinations of adhesives and resins after a short-term biofilm-induced degradation.

METHODS

Cervical cavities were prepared in bovine incisors, treated by Clearfil SE Bond 2 (SE) or FL-Bond II (FL), restored by Clearfil Majesty ES Flow (ES) or Beautifil Flow Plus (BFP) and grouped into SE-ES, SE-BFP, FL-ES and FL-BFP. After biofilm challenge, interfacial gaps and dentin wall lesions were examined by optical coherence tomography (OCT). Gap depth (GD), gap pattern scale (GPS) and dentin wall lesion depth (WLD) were evaluated from confocal laser scanning microscope. Microhardness of dentin lesions was measured with a Vickers microhardness tester. Chemical elements in resins and dentin wall lesions were analyzed by scanning electron microscopy and energy dispersive X-ray spectrometry (SEM/EDS). Morphological structures of interfacial gaps were observed by SEM.

RESULTS

OCT could detect adhesive-dentin-bonded and adhesive-dentin-debonded gaps. SE-containing groups showed significantly lower GPS than FL-containing groups. FL-BFP showed significantly lower WLD than FL-ES. Microhardness of dentin wall lesions was higher than that of outer lesions and they showed significant differences in FL-BFP. SE-BFP showed a lower GPS curve and higher intensities of Ca and P in the upper half of dentin wall lesions than other groups. From SEM, microgaps between filler and matrix, break and loss of matrix, separation of adhesive matrix with hybrid layer occurred at interfacial gaps.

SIGNIFICANCE

The morphological, mechanical and chemical characteristics of resin-dentin interfacial degradation depend on the component and chemistry of restorative materials.

Influence of polymerization pressure and post-cure treatment on conversion degree and viscoelastic properties of polymer infiltrated ceramic network

This study aimed at determining an optimum polymerization pressure for Polymer Infiltrated Ceramic Network (PICN) blocks by characterizing the conversion degree (DC) and the viscoelastic properties of experimental PICN blocks polymerized at 90 °C under various high pressures followed or not by post-cure treatment (PC). Near infrared analysis and dynamic mechanical analysis were used to characterize DC and viscoelastic properties of sixteen PICN: one control (thermo-cured) and fifteen experimental groups (one thermo-cured followed by PC and fourteen high pressure polymerized PICN, in the range of 50-350 MPa without and with PC). Conversion degree of high pressure polymerized PICN blocks without post curing displays an optimum between 100 and 150 MPa resulting in an improved E' and T_g. Post curing induces a higher DC with a controversial effect on thermomechanical properties. The results suggested that 100-150 MPa without PC is an optimum polymerization parameter, resulting in PICN blocks with significantly better DC, T_g, E'.

Antimicrobial antidegradative dental adhesive preserves restoration-tooth bond

OBJECTIVE

Assess the ability of an antimicrobial drug-releasing resin adhesive, containing octenidine dihydrochloride (OCT)-silica co-assembled particles (DSPs), to enhance the biostability and preserve the interfacial fracture toughness (FT) of composite restorations bonded to dentin. Enzyme-catalyzed degradation compromises the dental restoration-tooth interface, increasing cariogenic bacterial infiltration. In addition to bacterial ingress inhibition, antimicrobial-releasing adhesives may exhibit direct interfacial biodegradation inhibition as an additional benefit.

METHODS

Mini short-rod restoration bonding specimens with total-etch adhesive with/without 10% wt. DSPs were made. Interfacial fracture toughness (FT) was measured as-manufactured or post-incubation in simulated human salivary esterase (SHSE) for up to 6-months. Effect of OCT on SHSE and whole saliva/bacterial enzyme activity was assessed. Release of OCT outside the restoration interface was assessed.

RESULTS

No deleterious effect of DSPs on initial bonding capacity was observed. Aging specimens in SHSE reduced FT of control but not DSP-adhesive-bonded specimens. OCT inhibited SHSE degradation of adhesive monomer and may inhibit endogenous proteases. OCT inhibited bacterial esterase and collagenase. No endogenous collagen breakdown was detected in the present study. OCT increased human saliva degradative esterase activity below its minimum inhibitory concentration towards S. mutans (MIC), but inhibited degradation above MIC. OCT release outside restoration margins was below detection.

SIGNIFICANCE

DSP-adhesive preserves the restoration bond through a secondary enzyme-inhibitory effect of released OCT, which is virtually confined to the restoration interface microgap. Enzyme activity modulation may produce a positive-to-negative feedback switch, by increasing OCT concentration via biodegradation-triggered release to an effective dose, then subsequently slowing degradation and degradation-triggered release.

Hardness and fracture toughness of resin-composite materials with and without fibers

OBJECTIVE

To investigate the surface micro-hardness (VHN) and fracture toughness (K_IC) of resin-composites, with and without incorporated short fibers, after solvent storage.

METHODS

Three resin-composites incorporating fibers, additional to particle reinforcement, were examined: everX™, NovoPro Fill™ and NovoPro Flow™. Four composites were used as controls, with only particle reinforcement: Filtek bulk Fill™, Filtek bulk one™, Filtek XTE™, and Filtek Flow XTE™. For hardness measurement, materials were cured in 2mm thick molds for 20s by a LED source of average irradiance 1.2W/cm². Specimens (n=6/group) were stored dry for 1h and then in either water or 75% ethanol/water for 1h, 1 day and 30 days at 37±1°C. Vickers hardness was measured under a load of 300g for 15s. For fracture toughness (K_IC) measurements, single-edge-notched specimens (n=6/group) were prepared: (32×6×3mm) for 3-point bending and stored for 1 and 7 days in water at 37°C. Fractured surfaces of fiber-reinforced composite were examined by scanning electron microscopy (SEM). VHN data were analyzed using three-way ANOVA, one-way ANOVA and the Tukey post hoc test (p≤0.05). K_IC data were analyzed by two-way ANOVA and one-way ANOVA and the Tukey post hoc test (p≤0.05). An independent t-test was used to detect differences (α=0.05) in K_IC between stored groups for each material.

RESULTS

VHN decreased for all composites with storage time in both solvents, but more appreciably in 75% ethanol/water (an average of 20%). K_IC ranged from 2.14 (everX Posterior) to 0.96 NovoPro Flow) MPa.m^0.5. The longer storage period (7 days) had no significant effect on this property relative to 1 day storage.

SIGNIFICANCE

Reinforcement with short fibers, and possibly matrix compositional differences, significantly enhanced the fracture toughness of EVX. However, for nano-fiber containing composites, there were no evident beneficial effects upon either their fracture toughness or hardness compared to a range of control composites. Water storage for 7 days of all these resin-composites produced no significant change in their K_IC values, relative to 1 day storage.

Human neutrophils degrade methacrylate resin composites and tooth dentin

Cholesterol esterase-like (CE) activity from saliva and esterase from cariogenic bacteria hydrolyze ester linkages of dental methacrylate resins. Collagenolytic, matrix metalloproteinase-like (MMP) activities from dentin and bacteria degrade collagen in demineralized tooth dentin. Human neutrophils in the oral cavity contain factors that are hypothesized to have CE and MMP activities that could contribute to the degradation of methacrylate resins and dentinal collagen. OBJECTIVES: To measure the CE and MMP activities from human neutrophils and their ability to degrade dental methacrylate resin composite and dentinal collagen. Neutrophils' CE and MMP activities were measured using nitrophenyl-esters or fluorimetric MMP substrates, respectively. Neutrophils' degradation of resin composite and dentinal collagen was quantified by measuring release of a universal 2,2-Bis[4-(2-hydroxy-3-methacryloxypropoxy)phenyl]propane (bisGMA)-derived resin composite degradation byproduct, bishydroxy-propoxy-phenyl-propane (bisHPPP), or a collagen degradation by-product, hydroxyproline, respectively using ultra performance liquid chromatography/mass spectrometry. Neutrophils' CE activity increased the release of bisHPPP from bisGMA monomer compared to control after 24 and 48 h (p < 0.05). Neutrophils degraded polymerized resin composite and produced higher amounts of bisHPPP than buffer after 48 h of incubation (p < 0.05). Neutrophils show generic MMP, gelatinase, MMP-2 and MMP-9, and collagenase, MMP-1 and MMP-8 activities that were stable or increased over the first 24 h (p < 0.05). Neutrophils degraded demineralized dentin more than buffer-only groups, indicated by higher amounts of hydroxyproline (p < 0.05). The ability of neutrophils to degrade both dental resin composite and tooth dentin, suggest neutrophil's potential role in root caries, and in recurrent carries by accelerating the degradation of resin-dentin interfaces, and compromising the longevity of the restoration. STATEMENT OF SIGNIFICANCE: Neutrophils are part of the innate immune system and are constantly entering the oral cavity through the gingival sulcus, in direct contact with the tooth, restoration, restoration-tooth margins and pathogenic bacteria. The current study is the first to characterize and quantify degradative activities from neutrophils toward methacrylate resin and demineralized dentin, the two main components of the restoration-tooth interface, suggesting that this interface could be negatively influenced by neutrophils, potentially contributing to increase in caries formation and progression, and premature restoration failure. This study provides a significant finding to the biomaterials and oral health fields by identifying a potential weakness in current restorative procedures and materials used to manage gingival proximal and cervical gingival or sub-gingival carious lesions.

TEGDMA releasing in resin composites with different filler contents and its correlation with mitochondrial mediated cytotoxicity in human gingival fibroblasts

Compositions of resin composite exhibit cytotoxicity, especially Triethylene-glycol-dimethacrylate (TEGDMA), yet the underlying mechanisms and its relationship with filler content are poorly understood. Here, specimens of five composites (VITA LC, VITA ZETA, Z350, Filtek P60, and AP-X), containing different filler size and weight, were immersed into culture medium for 72 h. After TEGDMA quantification, the resin composite eluates were used to incubate HGFs. Cellular viability was evaluated. Total reactive oxygen species (ROS) and mitochondrial ROS were detected to assess oxidative stress. Adenosine triphosphate and cytochrome c oxidase (CcO) activity, mitochondrial membrane potential and morphology, mitochondrial biogenesis regulators were analyzed to evaluate mitochondrial functions. Results showed that TEGDMA release negatively correlated to filler size and weight of tested composites. Although cell viability reduction was not significant, total and mitochondrial ROS production showed a positive relationship with the amount of TEGDMA in composite eluates. Furthermore, the expression of mitochondrial biogenesis markers and mitochondrial fusion protein, were markedly elevated in TEGDMA rich eluates, especially in VITA-LC group, shown as elongated mitochondrial morphology and aberrant mitochondrial functions. Overall, TEGDMA could elute easier from those resin composites with less filler content and cause oxidative stress in HGFs via mitochondria dysregulation. These data can be instructive to optimize the synthesis of resin composites from the perspective of biocompatibility. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 107A: 1132-1142, 2019.

Evaluation of biofilm formation on novel copper-catalyzed azide-alkyne cycloaddition (CuAAC)-based resins for dental restoratives

OBJECTIVE

For the past several decades, the resins used in dental restorations have been plagued with numerous problems, including their implication in biofilm formation and secondary caries. The need for alternative resins is critical, and evaluation of biofilm formation on these resins is essential. The aim of this study was to evaluate in vitro biofilm formation on the surface of novel copper(I)-catalyzed azide-alkyne cycloaddition (CuAAC)-based resins and composites.

METHODS

CuAAC-based resins/composites made from varying azide monomers and different copper concentrations were compared with BisGMA-TEGDMA resins/composites that served as the control. Biofilms were formed using a mono-species model containing a luciferase-expressing strain of Streptococcus mutans. Luciferase activity was measured and the number of viable bacteria was enumerated on biofilms associated with each resin and composite.

RESULTS

A significant reduction (p<0.05) in luciferase activity, and the number of viable bacteria recovered from biofilms on CuAAC-based resins and composites was observed in comparison to biofilms associated with the BisGMA-TEGDMA controls.

SIGNIFICANCE

CuAAC-based resins do still allow for the formation of biofilms; however, the statistically significant reduction of growth that was associated with the CuAAC resin may enhance the longevity of restorations that incorporate CuAAC-based materials.

Gene expression and protein synthesis of esterase from Streptococcus mutans are affected by biodegradation by-product from methacrylate resin composites and adhesives

An esterase from S. mutans UA159, SMU_118c, was shown to hydrolyze methacrylate resin-based dental monomers.

OBJECTIVE

To investigate the association of SMU_118c to the whole cellular hydrolytic activity of S. mutans toward polymerized resin composites, and to examine how the bacterium adapts its hydrolytic activity in response to environmental stresses triggered by the presence of a resin composites and adhesives biodegradation by-product (BBP).

MATERIALS AND METHODS

Biofilms of S. mutans UA159 parent wild strain, SMU_118c knockout strain (ΔSMU_118c), and SMU_118c complemented strain (ΔSMU_118cC) were incubated with photo-polymerized resin composite. High performance liquid chromatography was used to quantify the amount of a universal 2,2-Bis[4-(2-hydroxy-3-methacryloxypropoxy)phenyl]propane (bisGMA)-derived BBP, bishydroxy-propoxy-phenyl-propane (bisHPPP) in the media. Fluorescence in situ hybridization (FISH) and quantitative proteomic analysis were used to measure SMU_118c gene expression and production of SMU_118c protein, respectively, from biofilms of S. mutans UA159 wild strain that were cultured with bisHPPP.

RESULTS

The levels of bisHPPP released from composite were similar for ΔSMU_118c and media control, and these were significantly lower compared to the parent wild-strain UA159 and complemented strain (ΔSMU_118cC) (p < 0.05). Gene expression of SMU_118c and productions of SMU_118c protein were higher for bisHPPP incubated biofilms (p < 0.05).

SIGNIFICANCE

This study suggests that SMU_118c is a dominant esterase in S. mutans and capable of catalyzing the hydrolysis of the resinous matrix of polymerized composites and adhesives. In turn, the bacterial response to BBP was to increase the expression of the esterase gene and enhance esterase production, potentially accelerating the biodegradation of the restoration, adhesive and restoration-tooth interface, ultimately contributing to premature restoration failure.

STATEMENT OF SIGNIFICANCE

We recently reported (Huang et al., 2018) on the isolation and initial characterization of a specific esterase (SMU_118c) from S. mutans that show degradative activity toward the hydrolysis of dental monomers. The current study further characterize this enzyme and shows that SMU_118c is a dominant degradative esterase activity in the cariogenic bacterium S. mutans and is capable of catalyzing the hydrolysis of the resinous matrix of polymerized composites and adhesives. In turn, the bacterial response to biodegradation by-products from composites and adhesives was to increase the expression of the esterase gene and enhance esterase production, accelerating the biodegradation of the restoration, adhesive and the restoration-tooth interface, potentially contributing to the pathogenesis of recurrent caries around resin composite restorations.

Biostable, antidegradative and antimicrobial restorative systems based on host-biomaterials and microbial interactions

OBJECTIVES

Despite decades of development and their status as the restorative material of choice for dentists, resin composite restoratives and adhesives exhibit a number of shortcomings that limit their long-term survival in the oral cavity. Herein we review past and current work to understand these challenges and approaches to improve dental materials and extend restoration service life.

METHODS

Peer-reviewed work from a number of researchers as well as our own are summarized and analyzed. We also include yet-unpublished work of our own. Challenges to dental materials, methods to assess new materials, and recent material improvements and research directions are presented.

RESULTS

Mechanical stress, host- and bacterial-biodegradation, and secondary caries formation all contribute to restoration failure. In particular, several host- and bacterial-derived enzymes degrade the resin and collagen components of the hybrid layer, expanding the marginal gap and increasing access to bacteria and saliva. Furthermore, the virulence of cariogenic bacteria is up-regulated by resin biodegradation by-products, creating a positive feedback loop that increases biodegradation. These factors work synergistically to degrade the restoration margin, leading to secondary caries and restoration failure. Significant progress has been made to produce hydrolytically stable resins to resist biodegradation, as well as antimicrobial materials to reduce bacterial load around the restoration. Ideally, these two approaches should be combined in a holistic approach to restoration preservation.

SIGNIFICANCE

The oral cavity is a complex environment that poses an array of challenges to long-term material success; materials testing conditions should be comprehensive and closely mimic pathogenic oral conditions.

Responsive antimicrobial dental adhesive based on drug-silica co-assembled particles

Most dental resin composite restorations are replacements for failing restorations. Degradation of the restoration-tooth margins by cariogenic bacteria results in recurrent caries, a leading cause for restoration failure. Incorporating antimicrobial agents in dental adhesives could reduce interfacial bacterial count and reduce recurrent caries rates, inhibit interfacial degradation, and prolong restoration service life, while minimizing systemic exposure. Direct addition of antimicrobial compounds into restorative materials have limited release periods and could affect the integrity of the material. Attempts to incorporate antimicrobial within mesoporous silica nanoparticles showed theoretical promise due to their physical robustness and large available internal volume, yet yielded short-term burst release and limited therapeutic payload. We have developed novel broad-spectrum antimicrobial drug-silica particles co-assembled for long-term release and high payload incorporated into dental adhesives. The release of the drug, octenidine dihydrochloride, is modulated by the oral degradative environment and mathematically modeled to predict effective service life. Steady-state release kills cariogenic bacteria, preventing biofilm formation over the adhesive surface, with no toxicity. This novel material could extend dental restoration service life and may be applied to other long-term medical device-tissue interfaces for responsive drug release upon bacterial infection.

STATEMENT OF SIGNIFICANCE

This study describes a novel dental adhesive that includes a broad-spectrum antimicrobial drug-silica co-assembled particles for long-term antimicrobial effect. The release of the drug, octenidine dihydrochloride, is modulated by the oral degradative environment and mathematically modeled to predict effective release throughout the service life of the restoration. Steady-state drug-release kills caries-forming bacteria, preventing biofilm formation over the adhesive surface, without toxicity. This novel material could extend dental restoration service life and may be applied to other long-term medical device-tissue interfaces for responsive drug release upon bacterial infection. Since recurrent cavities (caries) caused by bacteria are the major reason for dental filling failure, this development represents a significant contribution to the biomaterials field in methodology and material performance.

Short-time dental resin biostability and kinetics of enzymatic degradation

Resin biostability is of critical importance to the durability of methacrylate-based dental resin restorations. Current methods for evaluating biostability take considerable time, from weeks to months, and provide no short-time kinetics of resin degradation. The objective of this study is to develop a more sensitive method to assess resin biostability over short-time spans (hours to days) that will enhance our understanding of biostability and its resin chemistry. Ultra-flat resin films of equimolar urethane dimethacrylate (UDMA) and triethylene glycol dimethacrylate (TEGDMA) are produced through photo-curing between two flat surfaces. Next, metal-covered enclaves and bare-resin channels are generated using stencil lithography to create both degradable and protected (internal reference) regions simultaneously in a single specimen. Resins having three different degrees of vinyl conversion (DC) are compared, and changes of surface roughness and step height in the two regions are monitored by atomic force microscopy (AFM) before and after incubated in enzyme solutions and saline controls. Specimen biostability is ranked based on the topological profile changes when viewed in cross-section before and after enzymatic challenges. In addition, a model is proposed to quantify specimen enzymatic degradation. Based on this model, enzymatic degradation is detected as early as 4 h, and a surge of enzymatic degradation is detected between 4 h and 8 h. The correlation between the DC of resin network and the surge in degradation is discussed. In summary, this new method is effective in ranking biostability and quantifying enzymatic degradation while also reducing labor, time and cost, which lends itself well to materials development and evaluation of dental resins.

STATEMENT OF SIGNIFICANCE

We report, for the first time, the short-time kinetics of enzymatic degradation of methacrylate dental resins. A nanotechnology based method is developed to accelerate the evaluation of resin biostability. This new method reduces experimental time from weeks to one or two days, which will significantly reduce the costs of labor and enzymes. It also introduces a corresponding parameter (ΔH) and a three-cause model for ranking biostability, which confirms the correlation of chemical structure (DC) and material performance and opens new opportunities for studying the resin biostability and its impact on dental applications. Overall, this is a new tool for evaluating resin biostability and developing new materials.

Biofilm-induced changes to the composite surface

OBJECTIVES

Composites may undergo biodegradation in the oral cavity. The objective was to investigate the effect of single- and multi-species biofilms on the surface roughness and topography of two composites.

METHODS

Disk-shaped specimens of a paste-like, Bis-GMA-free (Gradia Direct Anterior, GC), and a flowable, Bis-GMA-based composite (Tetric EvoFlow, Ivoclar-Vivadent) were prepared. After ethylene-oxide sterilization (38°C), specimens (n=3) were incubated with Streptococcus mutans or mixed bacterial culture (Streptococcus mutans, Streptococcus sanguinis, Actinomyces naeslundii and Fusobacterium nucleatum). As negative controls, unexposed specimens and specimens exposed to sterile medium (BHI) were used. Specimens exposed to acidified BHI medium (pH=5) and enzymatic solution of cholesterol esterase served as positive control. Following 6-week incubation, the attached biofilms were collected for real-time PCR assessment, after which the surface roughness and topography of the specimens were analyzed with atomic force microscopy. Surface hydrophilicity/hydrophobicity was determined by contact angle measurements. Biofilm structure was analyzed with scanning electron microscopy.

RESULTS

Even though multi-species biofilms were thicker, with more cells attached, they did not significantly affect the surface roughness of the composites. On the other hand, S. mutans alone significantly increased the roughness of Tetric by 40.3%, while its effect on Gradia was lower (12%). The total amount of attached bacteria, however, did not differ between the composites.

CONCLUSIONS

S. mutans can increase the surface roughness of composites, depending on their composition. This ability of S. mutans is, however, mitigated in co-culture with other species. In particular, bacterial esterases seem to be responsible for the increased composite surface roughness upon biofilms exposure.

CLINICAL SIGNIFICANCE

Cariogenic bacteria can degrade composites, thereby increasing the surface roughness. Increased roughness and subsequent improved bacterial accumulation may facilitate the development of secondary caries around composites, which is the most common reason for the restoration failure.

Mechanistic, genomic and proteomic study on the effects of BisGMA-derived biodegradation product on cariogenic bacteria

OBJECTIVES

Investigate the effects of a Bis-phenyl-glycidyl-dimethacrylate (BisGMA) biodegradation product, bishydroxypropoxyphenyl-propane (BisHPPP), on gene expression and protein synthesis of cariogenic bacteria.

METHODS

Quantitative real-time polymerase chain reaction was used to investigate the effects of BisHPPP on the expression of specific virulence-associated genes, i.e. gtfB, gtfC, gbpB, comC, comD, comE and atpH in Streptococcus mutans UA159. Possible mechanisms for bacterial response to BisHPPP were explored using gene knock-out and associated complemented strains of the signal peptide encoding gene, comC. The effects of BisHPPP on global gene and protein expression was analyzed using microarray and quantitative proteomics. The role of BisHPPP in glucosyltransferase (GTF) enzyme activity of S. mutans biofilms was also measured.

RESULTS

BisHPPP (0.01, 0.1mM) up-regulated gtfB/C, gbpB, comCDE, and atpH most pronounced in biofilms at cariogenic pH (5.5). The effects of BisHPPP on the constructed knock-out and complemented strains of comC from quorum-sensing system, implicated this signaling pathway in up-regulation of the virulence-associated genes. Microarray and proteomics identified BisHPPP-regulated genes and proteins involved in biofilm formation, carbohydrate transport, acid tolerance and stress-response. GTF activity was higher in BisHPPP-exposed biofilms when compared to no-BisHPPP conditions.

SIGNIFICANCE

These findings provide insight into the genetic and physiological pathways and mechanisms that help explain S. mutans adaptation to restorative conditions that are conducive to increased secondary caries around resin composite restorations and may provide guidance to clinicians' decision on the selection of dental materials when considering the long term oral health of patients and the interactions of composite resins with oral bacteria.

Triethylene Glycol Up-Regulates Virulence-Associated Genes and Proteins in Streptococcus mutans

Triethylene glycol dimethacrylate (TEGDMA) is a diluent monomer used pervasively in dental composite resins. Through hydrolytic degradation of the composites in the oral cavity it yields a hydrophilic biodegradation product, triethylene glycol (TEG), which has been shown to promote the growth of Streptococcus mutans, a dominant cariogenic bacterium. Previously it was shown that TEG up-regulated gtfB, an important gene contributing to polysaccharide synthesis function in biofilms. However, molecular mechanisms related to TEG’s effect on bacterial function remained poorly understood. In the present study, S. mutans UA159 was incubated with clinically relevant concentrations of TEG at pH 5.5 and 7.0. Quantitative real-time PCR, proteomics analysis, and glucosyltransferase enzyme (GTF) activity measurements were employed to identify the bacterial phenotypic response to TEG. A S. mutans vicK isogenic mutant (SMΔvicK1) and its associated complemented strain (SMΔvicK1C), an important regulatory gene for biofilm-associated genes, were used to determine if this signaling pathway was involved in modulation of the S. mutans virulence-associated genes. Extracted proteins from S. mutans biofilms grown in the presence and absence of TEG were subjected to mass spectrometry for protein identification, characterization and quantification. TEG up-regulated gtfB/C, gbpB, comC, comD and comE more significantly in biofilms at cariogenic pH (5.5) and defined concentrations. Differential response of the vicK knock-out (SMΔvicK1) and complemented strains (SMΔvicK1C) implicated this signalling pathway in TEG-modulated cellular responses. TEG resulted in increased GTF enzyme activity, responsible for synthesizing insoluble glucans involved in the formation of cariogenic biofilms. As well, TEG increased protein abundance related to biofilm formation, carbohydrate transport, acid tolerance, and stress-response. Proteomics data was consistent with gene expression findings for the selected genes. These findings demonstrate a mechanistic pathway by which TEG derived from commercial resin materials in the oral cavity promote S. mutans pathogenicity, which is typically associated with secondary caries.

Preparation of Dental Resins Resistant to Enzymatic and Hydrolytic Degradation in Oral Environments

The short average service life of traditional dental composite restorative materials and increasing occurrence of secondary caries adjacent to composite restorations and sealants are necessitating the development of new, longer lasting compositions. Novel monomers and their polymers, reinforcing fillers, and adhesive components are needed. The goal of this research is to develop resin systems for use in restorations, sealants, and other dental services that are superior in properties and endurance to currently used bisphenol A glycidyl dimethacrylate/triethylene glycol dimethacrylate (Bis-GMA/TEGDMA) and urethane-dimethacrylate products. Ether-based monomers and their polymers that were not susceptible to enzymatic or hydrolytic degradation were prepared and characterized. They showed no degradation under hydrolytic and enzymatic challenges, whereas the hydrolysis of ester links weakened contemporary resins within 16 days under these challenges. The success of the ether-based materials is promising in making durable systems that are subjected to long-term biochemical and hydrolytic challenges in oral environments.

In vitro studies on the cytotoxic potential of surface sealants

OBJECTIVE

The objective of this in vitro study was an initial screening of the cytotoxic potential of widely used smooth enamel surface sealants.

MATERIALS AND METHODS

A total of 20 products were allocated to four groups based on their chemical composition: (1) filled resin-based sealants, (2) unfilled resin-based sealants, (3) a resin-modified, glass ionomer-based sealant, and (4) silicone-based sealants. All materials were applied to human enamel slices both in accordance with manufacturers' instructions and in additional experiments applying 50% undercuring and 50% overcuring. An agar overlay assay was then used to test the specimens following ISO 10933. The cytotoxic potential of each material was interpreted based on a reaction index that summarized the decolorization and lysis scores obtained.

RESULTS

The cytotoxic potential decreased as follows: unfilled resin-based sealants > filled resin-based sealants > resin-modified, glass ionomer-based sealant > silicone-based sealants. In 75% of the resin-based products, deliberate undercuring was associated with more extensive decolorization zones, leading to higher rates of cytotoxic potential in two of those products. Overcuring, by contrast, was associated with a tendency for smaller decolorization zones in 50% of the resin-based products.

CONCLUSION

Surface sealants derived from resin monomers exhibited cytotoxic potential in the agar overlay assay. There is also evidence of a possible association with curing, as undercuring can increase the cytotoxic potential, whereas normal curing (as per manufacturers' instructions) or overcuring may help minimize such effects. More research into the biological implications of these materials is needed, especially with regard to their potential impact on the adjacent gingiva.

Cariogenic bacteria degrade dental resin composites and adhesives

A major reason for dental resin composite restoration replacement is related to secondary caries promoted by acid production from bacteria including Streptococcus mutans (S. mutans). We hypothesized that S. mutans has esterase activities that degrade dental resin composites and adhesives. Standardized specimens of resin composite (Z250), total-etch (Scotchbond Multipurpose, SB), and self-etch (Easybond, EB) adhesives were incubated with S. mutans UA159 or uninoculated culture medium (control) for up to 30 days. Quantification of the BisGMA-derived biodegradation by-product, bishydroxy-propoxy-phenyl-propane (BisHPPP), was performed by high-performance liquid chromatography. Surface analysis of the specimens was performed by scanning electron microscopy (SEM). S. mutans was shown to have esterase activities in levels comparable with those found in human saliva. A trend of increasing BisHPPP release throughout the incubation period was observed for all materials and was more elevated in the presence of bacteria vs. control medium for EB and Z250, but not for SB (p < .05). SEM confirmed the increased degradation of all materials with S. mutans UA159 vs. control. S. mutans has esterase activities at levels that degrade resin composites and adhesives; degree of degradation was dependent on the material's chemical formulation. This finding suggests that the resin-dentin interface could be compromised by oral bacteria that contribute to the progression of secondary caries.

Factors Involved in Mechanical Fatigue Degradation of Dental Resin Composites

The design of clinical trials allows for limited insights into the fatigue processes occurring in resin composites and the factors involved therein. In vitro studies, in contrast, can fundamentally narrow study interests to focus on particular degradation mechanisms and, to date, represent the major contributors to the state of knowledge on the subject. These studies show that microstructural features are important in determining strength and fracture toughness, whereas fatigue resistance is mainly related to the susceptibility of the matrix and the filler/matrix interface to mechanical and chemical degradation. In this review, we focus on fracture mechanisms occurring during fatigue, on the methods used to assess them, and on additional phenomena involved in the degradation of initial mechanical properties of resin composites.

Influence of filler addition, storage medium and evaluation time on biaxial flexure strength and modulus of adhesive systems

OBJECTIVE

This study evaluated the effects of filler addition, storage medium and time on biaxial flexural strength and flexural modulus of six adhesive systems.

MATERIALS AND METHODS

The adhesives were either unfilled resins: Single Bond, Prime&Bond 2.1 and One-Step; or filled resins: Single Bond Plus, Prime&Bond NT and One-Step Plus. Resin discs of each product (0.5 mm thick × 6.0 mm diameter) were prepared using silicon molds (n = 10). The discs were stored dry, in water, mineral oil or ethanol for 1 week or 3 months before biaxial flexural testing. Data were statistically analyzed by 3-way ANOVA and Tukey's post-hoc test (α = 0.05). The specimens were tested in a universal testing machine at 1.27 mm/min until failure occurred.

RESULTS

In general, the storage in ethanol led to significantly lower flexural strength and flexural modulus values than the other storage conditions for all adhesives in both storage periods. Filler addition increased flexural strength and flexural modulus for Prime&Bond NT, when it was stored dry or in water for 1 week. For Single Bond Plus, the filler addition resulted in higher flexural modulus, when it was stored for 1 week in oil and in ethanol. No significant differences in flexural modulus were observed between One-Step and One-Step Plus in any storage medium.

CONCLUSIONS

Results suggested that filler addition does not necessarily have to increase the flexural strength and flexural modulus. Ethanol and oil storages tended to yield opposite effects.

Determination of neutralization capacity and stability of a basic methacrylate monomer using NMR

The durability of dental resin depends on the stability of the polymer. The neutralizing capacity of a basic methacrylate monomer and its chemical stability were measured using nuclear magnetic resonance (NMR) spectroscopy. Lactic acid solution was titrated with 2-(dimethylamino)ethylmethacrylate (DMAEMA) or 2-hydroxyethylmethacrylate (HEMA) and its chemical shifts monitored. Addition of DMAEMA alters the chemical shift proportionally to pH neutralization, whereas HEMA has no impact. Chemical shifts were used to quantify both the change in pH and monomer stability. The results demonstrate that neutralization by basic monomer can be achieved and that this can be measured using an NMR assay.

The Influence of Time and Cement Type on Push-Out Bond Strength of Fiber Posts to Root Dentin

A self-adhesive resin cement can provide a significantly stronger bond than a three-step etch-and-rinse adhesive and resin cement when used to lute fiber posts.

Brillouin spectroscopy studies of two-component polymerizable liquid system: 2,2-bis[4-(2-hydroxymethacryloxypropoxy)phenyl]propane/benzyl methacrylate

Brillouin spectroscopy was used to investigate viscoelastic properties of a two-component system consisting of a high viscosity liquid (HVL) and a low viscosity liquid (LVL), both able to polymerize. The model liquids were: 2,2-bis[4-(2-hydroxymethacryloxypropoxy)phenyl]propane (abbreviated as bis-GMA, HVL) and benzyl methacrylate (BzMA, LVL). The viscosity of the system was regulated by changing the monomer ratio. Hypersonic velocity and attenuation coefficient were investigated in a temperature range covering viscoelastic relaxation process. The dependence of the longitudinal viscosity on the system composition was determined. Additionally, the Brillouin studies were accompanied by some supplementary experimental methods, like low frequency shear viscosity measurements and observations of phase transitions by differential scanning calorimetry (DSC). The investigated monomer mixtures were then polymerized in a light-induced process and the polymerization kinetic curves were measured to find the possible correlation between the viscoelastic properties of the monomer mixture (as observed by Brillouin spectroscopy) and the polymerization course.

Effect of salivary esterase on the integrity and fracture toughness of the dentin-resin interface

Human Salivary Derived Esterases (HSDE) are part of the salivary group of enzymes which show strong degradative activity toward the breakdown of one of the most common monomers used in dental composites and adhesives, 2,2-[4(2-hydroxy 3-methacryloxypropoxy)-phenyl] propane (Bis-GMA), to form the degradation product 2,2-bis [4 (2,3-hydroxy-propoxy)phenyl] propane (Bis-HPPP). This study was aimed to evaluate the effects of HSDE on the biodegradation and fracture toughness of the adhesive resin-dentin interface. Adhesive resin (Scotchbond Multi Purposes), resin composite (Z250) and mini short-rod specimens, were either not incubated; or incubated in phosphate-buffered saline (PBS) or HSDE media for up to 180 days (37 degrees C, pH 7.0). The amount of Bis-HPPP was analyzed by high performance liquid chromatography and mini-SR specimens were tested for fracture toughness using universal testing machine following 30, 90, or 180-day incubation periods. Significantly higher amounts of Bis-HPPP were produced in HSDE than in PBS incubated specimens (p < 0.05). Non-incubated mini-SR specimens had the higher fracture-toughness values, while specimens incubated for 180-days in HSDE had the lowest fracture toughness (p < 0.05). This study suggests that biodegradation is an on-going clinically relevant process that progressively compromises the integrity of the critical resin restoration-adhesive interface, as well as the resin-composite component with time.

Biodegradation of resin-dentin interfaces increases bacterial microleakage

Bis-GMA-containing resin composites and adhesives undergo biodegradation by human-saliva-derived esterases, yielding Bis-hydroxy-propoxy-phenyl-propane (Bis-HPPP). The hypothesis of this study is that the exposure of dental restorations to saliva-like esterase activities accelerates marginal bacterial microleakage. Resin composites (Scotchbond, Z250, 3M) bonded to human dentin were incubated in either buffer or dual-esterase media (pseudocholinesterase/cholesterol-esterase; PCE+CE), with activity levels simulating those of human saliva, for up to 90 days. Incubation solutions were analyzed for Bis-HPPP by high-performance liquid chromatography. Post-incubation, specimens were suspended in a chemostat-based biofilm fermentor cultivating Streptococcus mutans NG8, a primary species associated with dental caries, for 7 days. Bacterial microleakage was assessed by confocal laser scanning microscopy. Bis-HPPP production and depth and spatial volume of bacterial cell penetration within the interface increased with incubation time and were higher for 30- and 90-day PCE+CE vs. buffer-incubated groups, suggesting that biodegradation can contribute to the formation of recurrent decay.

Enzyme-catalyzed hydrolysis of dentin adhesives containing a new urethane-based trimethacrylate monomer

A new trimethacrylate monomer with urethane-linked groups, 1,1,1-tri-[4-(methacryloxyethylamino-carbonyloxy)-phenyl]ethane (MPE), was synthesized, characterized, and used as a comonomer in dentin adhesives. Dentin adhesives containing 2-hydroxyethyl methacrylate (HEMA, 45% w/w) and 2,2-bis[4(2-hydroxy-3-methacryloyloxy-propyloxy)-phenyl] propane (BisGMA, 30% w/w) in addition to MPE (25% w/w) were formulated with H(2)O at 0 (MPE0), 8 (MPE8), and 16 wt % water (MPE16) to simulate the wet demineralized dentin matrix and compared with controls [HEMA /BisGMA, 45/55 w/w, at 0 (C0), 8 (C8), and 16 wt % water (C16)]. The new adhesive showed a degree of double bond conversion and mechanical properties comparable with control, with good penetration into the dentin surface and a uniform adhesive/dentin interface. On exposure to porcine liver esterase, the net cumulative methacrylic acid (MAA) released from the new adhesives was dramatically (p < 0.05) decreased relative to the control, suggesting that the new monomer improves esterase resistance.

Enzymatic biodegradation of HEMA/bisGMA adhesives formulated with different water content

Dentin adhesives may undergo phase separation when bonding to wet demineralized dentin. We hypothesized that adhesives exhibiting phase separation will experience enhanced biodegradation of methacrylate ester groups. The objective of this project was to study the effect of enzyme-exposure on the release of methacrylic acid (MAA) and 2-hydroxyethyl methacrylate (HEMA) from adhesives formulated under conditions simulating wet bonding. HEMA/bisGMA(2,2-bis[4(2-hydroxy-3-methacryloyloxy-propyloxy)-phenyl] propane), 45/55 w/w ratio, was formulated with different water content: 0 Wt % (A00), 8 wt % (A08), and 16 wt % (A16). After a three day prewash, adhesive discs were incubated with/without porcine liver esterase (PLE) in phosphate buffer (PB, pH 7.4) at 37 degrees C for 8 days. Supernatants were collected daily and analyzed for MAA and HEMA by HPLC. For all formulations, daily MAA release in the presence of PLE was increased compared to MAA release in PB. HEMA release in the presence of PLE was not detected while HEMA release was consistently measured in PB. A08 and A16 released significantly larger amounts of HEMA compared to A00. Analysis of the cumulative release of analytes showed that the leachables in PLE was significantly increased (p < 0.05) as compared with that released in PB indicating that MAA release was not only formed from unreacted monomers but from pendant groups in the polymer network. However, the levels of analytes HEMA in PB or MAA in PLE were increased in A08 and A16 as compared with A00, which suggests that there could be a greater loss of material in HEMA/bisGMA adhesives that experience phase separation under wet bonding conditions.

Effect of immersion in various media on the sorption, solubility, elution of unreacted monomers, and flexural properties of two model dental composite compositions

Immersion in various media has different effect on the properties of dental composites, such as sorption, solubility, elution of unreacted monomers, flexural strength, and flexural elastic modulus. In the present work, the effect of immersion in various media and the relationship between the variation of these properties and the components of dental composite were investigated. Two model dental composites were immersed in three different media-distilled water, artificial saliva, and ethanol/water, respectively, for a certain time. Their sorption, solubility, flexural strength, and flexural elastic modulus were tested according to the international standard. Elution of unreacted monomers was analyzed by using high performance liquid chromatography (HPLC) and the surface morphology of samples after immersion was observed using scanning electron microscope (SEM). The results showed that the effect on properties depended on the immersion media where ethanol/water had the most significant effect and these properties were related to the components of dental composite.