Material properties and bone marrow stromal cells response to in situ crosslinkable RGD-functionlized lactide-co-glycolide scaffolds

Osteogenic differentiation of human mesenchymal stem cells in freeze-gelled chitosan/nano β-tricalcium phosphate porous scaffolds crosslinked with genipin

The objective of this work was to investigate material properties and osteogenic differentiation of human mesenchymal stem cells (hMSCs) in genipin (GN) crosslinked chitosan/nano β-tricalcium phosphate (CS/nano β-TCP) scaffolds, and compare the results with tripolyphosphate (TPP) crosslinked scaffolds. Porous crosslinked CS/nano β-TCP scaffolds were produced by freeze-gelation using GN (CBG scaffold) and TPP (CBT scaffold) as crosslinkers. The prepared CBT and CBG scaffolds were characterized with respect to porosity, pore size, water content, wettability, compressive strength, mass loss, and osteogenic differentiation of hMSCs. All scaffolds displayed interconnected honeycomb-like microstructures. There was a significant difference between the average pore size, porosity, contact angle, and percent swelling of CBT and CBG scaffolds. The average pore size of CBG scaffolds was higher than CBT, the porosity of CBG was lower than CBT, the water contact angle of CBG was higher than CBT, and the percent swelling of CBG was lower than CBT. At a given crosslinker concentration, there was not a significant difference in compressive modulus and mass loss of CBG and CBT scaffolds. Metabolic activity of hMSCs seeded in CBG scaffolds was slightly higher than CBT. Furthermore, CBG scaffolds displayed slightly higher extent of mineralization after 21 days of incubation in osteogenic medium compared to CBT.

Time Dependence of Material Properties of Polyethylene Glycol Hydrogels Chain Extended with Short Hydroxy Acid Segments

The objective of this work was to investigate the effect of chemical composition and segment number (n) on gelation, stiffness, and degradation of hydroxy acid-chain-extended star polyethylene glycol acrylate (SPEXA) gels. The hydroxy acids included glycolide (G,), L-lactide (L), p-dioxanone (D) and -caprolactone (C). Chain-extension generated water soluble macromers with faster gelation rates, lower sol fractions, higher compressive moduli, and a wide-ranging degradation times when crosslinked into a hydrogel. SPEGA gels with the highest fraction of inter-molecular crosslinks had the most increase in compressive modulus with n whereas SPELA and SPECA had the lowest increase in modulus. SPEXA gels exhibited a wide range of degradation times from a few days for SPEGA to a few weeks for SPELA, a few months for SPEDA, and many months for SPECA. Marrow stromal cells and endothelial progenitor cells had the highest expression of vasculogenic markers when co-encapsulated in the faster degrading SPELA gel.

Drug release kinetics, cell uptake, and tumor toxicity of hybrid VVVVVVKK peptide-assembled polylactide nanoparticles

An exciting approach to tumor delivery is encapsulation of the drug in self-assembled polymer-peptide nanoparticles. The objective of this work was to synthesize a conjugate of low molecular weight polylactide (LMW PLA) and V6K2 peptide and investigate self-assembly, drug release kinetics, cell uptake and toxicity, drug pharmacokinetics, and tumor cell invasion with Doxorubicin (DOX) or paclitaxel (PTX). The results for PLA-V6K2 self-assembled NPs were compared with those of polyethylene glycol stabilized PLA (PLA-EG) NPs. The size of PLA-V6K2 and PLA-EG NPs was 100 ± 20 and 130 ± 50 nm, respectively, with polydispersity index of 1.04 and 1.14. The encapsulation efficiency of DOX in PLA-V6K2 and PLA-EG NPs was 44 ± 9% and 55 ± 5%, respectively, and that of PTX was >90 for both NP types. The release of DOX and PTX from PLA-V6K2 was slower than that of PLA-EG, and the release rate was relatively constant with time. Based on molecular dynamic simulation, the less hydrophobic DOX was distributed in the lactide core as well as the peptide shell, while the hydrophobic PTX was localized mainly to the lactide core. PLA-V6K2 NPs had significantly higher cell uptake by 4T1 mouse breast carcinoma cells compared to PLA-EG NPs, which was attributed to the electrostatic interactions between the peptide and negatively charged moieties on the cell membrane. PLA-V6K2 NPs showed no toxicity to marrow stromal cells. DOX-loaded PLA-V6K2 NPs showed higher toxicity to 4T1 cells and the DNA damage response, and apoptosis was delayed compared to the free DOX. DOX or PTX encapsulated in PLA-V6K2 NPs significantly reduced invasion of 4T1 cells compared to those cells treated with the drug in PLA-EG NPs. Invasion of 4T1 cells treated with DOX in PLA-V6K2 and PLA-EG NPs was 5 ± 1% and 30 ± 5%, respectively, and that of PTX was 11 ± 2% and 40 ± 7%. The AUC of DOX in PLA-V6K2 NPs was 67% and 21% higher than those of free DOX and PLA-EG NPs, respectively. DOX-loaded PLA-V6K2 NPs injected in C3HeB/FeJ mice inoculated with MTCL syngeneic breast cancer cells displayed higher tumor toxicity than PLA-EG NPs and lower host toxicity than the free DOX. Cationic PLA-V6K2 NPs with higher tumor toxicity than the PLA-EG NPs are potentially useful in chemotherapy.

Effect of grafting BMP2-derived peptide to nanoparticles on osteogenic and vasculogenic expression of stromal cells

Bone morphogenetic protein-2 (BMP2) plays a major role in initiating the cascade of osteogenesis. However, high doses of exogenous BMP2 coupled with diffusion away from the intended site cause adverse side-effects. An alternative is to use biodegradable polymeric nanoparticles (NPs) grafted with peptides of the active domains of BMP2. NPs present a multivalent form of the peptide for stronger interaction with cell surface receptors, leading to a stronger activation of osteogenic signalling pathways. The objective of this work was to compare osteogenic activity of the BMP2 peptide (BMP2Pe), corresponding to residues 73-92 of BMP2 protein (BMP2Pr), grafted to biodegradable NPs with that of BMP2 protein (BMP2Pr). BMP2Pe was functionalized with a cysteine residue and grafted to poly(lactide fumarate) and poly(lactide-co-ethylene oxide fumarate) (PLAF/PLEOF) NPs via a thioether link. The calcium content of bone marrow stromal (BMS) cells cultured in osteogenic medium supplemented with BMP2 peptide/protein-grafted NPs (BMP2Pe-gNP and BMP2Pr-gNP) was slightly higher than other BMP2-treated groups, but all osteogenic groups showed similar levels of mineralization after 21 days. The expression pattern of master transcription factors Dlx5 and Runx2 indicated that BMP2 protein induced faster osteogenic signalling than the BMP peptide. The expression level of Osteopontin (OP), Osteocalcin (OC) and PECAM-1 in the NP-grafted BMP2 groups was significantly higher than those of ungrafted BMP2Pr and BMP2Pe groups, which may be due to a more effective presentation of the peptide/protein to cell surface receptors, thus leading to a stronger interaction of the peptide/protein with clustered cell surface receptors.

Synthesis and Gelation Characteristics of Photo-Crosslinkable Star Poly(ethylene oxide-co-lactide-glycolide acrylate) Macromonomers

Viability of encapsulated cells in situ crosslinkable macromonomers depends strongly on the minimum concentration of polymerization initiators and monomers required for gelation. Novel 4-arm poly(ethylene oxide-co-lactide-glycolide acrylate) (SPELGA) macromonomers were synthesized and characterized with respect to gelation, sol fraction, degradation, and swelling in aqueous solution. SPELGA macromonomers were crosslinked in the absence of N-vinyl-2-pyrrolidone (NVP) monomer to produce a hydrogel network with a shear modulus of 27±4 kPa. The shear modulus of the gels increased by 170-fold as the macromonomer concentration was increased from 10 to 25 wt%. Sol fraction ranged between 8-18%. Addition of only 0.4 mol% NVP to the polymerization mixture increased modulus by 2.2-fold from 27±4 (no NVP) to 60±10 kPa. The higher modulus was attributed to the dilution effect of polymer chains in the sol, by delaying the onset of diffusion-controlled reaction, and cross-propagation of the growing chains with network-bound SPELGA acrylates. Degradation of SPELGA gels depended on water content and density of hydrolytically degradable ester groups.

Material properties and osteogenic differentiation of marrow stromal cells on fiber-reinforced laminated hydrogel nanocomposites

The fibrils in the bone matrix are glued together by extracellular matrix proteins to form laminated structures (osteons) to provide elasticity and a supportive substrate for osteogenesis. The objective of this work was to investigate material properties and osteogenic differentiation of bone marrow stromal (BMS) cells seeded on osteon-mimetic fiber-reinforced hydrogel/apatite composites. Layers of electrospun poly(l-lactide) fiber mesh coated with a poly(lactide-co-ethylene oxide fumarate) (PLEOF) hydrogel precursor solution were stacked and pressed together, and crosslinked to produce a laminated fiber-reinforced composite. Hydroxyapatite (HA) nanocrystals were added to the precursor solution to produce an osteoconductive matrix for BMS cells. Acrylamide-terminated Arg-Gly-Asp (RGD) peptide (Ac-GRGD) was conjugated to the PLEOF/HA hydrogel phase to promote focal point adhesion of BMS cells. Laminates were characterized with respect to the Young's modulus, degradation kinetics and osteogenic differentiation of BMS cells. The moduli of the laminates under dry and wet conditions were significantly higher than those of the fiber mesh and PLEOF/HA hydrogel, and within the range of values reported for wet human cancellous bone. At days 14 and 21, alkaline phosphatase (ALPase) activity of the laminates was significantly higher than those of the fiber mesh and hydrogel. Lamination significantly increased the extent of mineralization of BMS cells and laminates with HA and conjugated with RGD (Lam-RGD-HA) had 2.7-, 3.5- and 2.8-fold higher calcium content (compared to laminates without HA or RGD) after 7, 14 and 21days, respectively. The Lam-RGD-HA group had significantly higher expression of osteopontin and osteocalcin compared to the hydrogel or laminates without HA or RGD, consistent with the higher ALPase activity and calcium content of Lam-RGD-HA. Laminated osteon-mimetic structures have the potential to provide mechanical strength to the regenerating region as well as supporting the differentiation of progenitor cells to the osteogenic lineage.

Migration of marrow stromal cells in response to sustained release of stromal-derived factor-1alpha from poly(lactide ethylene oxide fumarate) hydrogels

Stromal derived factor-1alpha (SDF-1alpha) is an important chemokine in stem cell trafficking and plays a critical role in the homing of bone marrow stromal (BMS) cells. However, its use in tissue regeneration is limited by its relatively short half-life and the time-dependent nature of cell homing to the site of injury. The objective of this work was to investigate the release characteristics of SDF-1alpha from degradable poly(lactide ethylene oxide fumarate) (PLEOF) hydrogels and to determine the effect of sustained release of SDF-1alpha on migration of BMS cells. Three PLEOF hydrogels with poly(l-lactide) (PLA) fractions of 6%, 9%, and 24% by weight were synthesized. After the addition of chemokine, the polymerizing mixture was crosslinked to produce SDF-1alpha loaded PLEOF hydrogels. The hydrogels were characterized with respect to sol fraction, water uptake, degradation, SDF-1alpha loading efficiency and release kinetics, and migration rate of bone marrow stromal (BMS) cells. The more hydrophilic hydrogels with 6% and 9% PLA fraction had a pronounced burst release followed by a period of sustained release by diffusion for 21 days. The more hydrophobic hydrogel with 24% PLA fraction had a less pronounced burst release and displayed a slow but constant release by diffusion between days 1 and 9 followed by a fast release by diffusion-degradation from days 9 to 18. The fraction of active SDF-1alpha released from 6%, 9%, and 24% hydrogels after 21 days was 34.3%, 32.3%, and 35.8%, respectively. The migration of BMS cells in response to time-released SDF-1alpha closely followed the protein release kinetics from the hydrogels. The biodegradable PLEOF hydrogel may potentially be useful as a delivery matrix for sustained release of SDF-1alpha in the proliferative phase of healing for recruitment of progenitor cells in tissue engineering applications.

Migration of marrow stromal cells in response to sustained release of stromal-derived factor-1alpha from poly(lactide ethylene oxide fumarate) hydrogels

Stromal derived factor-1alpha (SDF-1alpha) is an important chemokine in stem cell trafficking and plays a critical role in the homing of bone marrow stromal (BMS) cells. However, its use in tissue regeneration is limited by its relatively short half-life and the time-dependent nature of cell homing to the site of injury. The objective of this work was to investigate the release characteristics of SDF-1alpha from degradable poly(lactide ethylene oxide fumarate) (PLEOF) hydrogels and to determine the effect of sustained release of SDF-1alpha on migration of BMS cells. Three PLEOF hydrogels with poly(l-lactide) (PLA) fractions of 6%, 9%, and 24% by weight were synthesized. After the addition of chemokine, the polymerizing mixture was crosslinked to produce SDF-1alpha loaded PLEOF hydrogels. The hydrogels were characterized with respect to sol fraction, water uptake, degradation, SDF-1alpha loading efficiency and release kinetics, and migration rate of bone marrow stromal (BMS) cells. The more hydrophilic hydrogels with 6% and 9% PLA fraction had a pronounced burst release followed by a period of sustained release by diffusion for 21 days. The more hydrophobic hydrogel with 24% PLA fraction had a less pronounced burst release and displayed a slow but constant release by diffusion between days 1 and 9 followed by a fast release by diffusion-degradation from days 9 to 18. The fraction of active SDF-1alpha released from 6%, 9%, and 24% hydrogels after 21 days was 34.3%, 32.3%, and 35.8%, respectively. The migration of BMS cells in response to time-released SDF-1alpha closely followed the protein release kinetics from the hydrogels. The biodegradable PLEOF hydrogel may potentially be useful as a delivery matrix for sustained release of SDF-1alpha in the proliferative phase of healing for recruitment of progenitor cells in tissue engineering applications.

Role of substrate microstructure on osteogenic differentiation of mesenchymal stem cells

The objective of this work was to investigate the effect of substrate microstructure (planar versus microtubular geometry) on the extent of osteogenic differentiation of bone mesenchymal stem (BMS) cells. For laminated sheets, the BMS cell suspension was seeded on the sheets and cultured in complete osteogenic media. For laminated microtubes, the BMS cell suspension was injected in the tubes and allowed to incubate in osteogenic media. BMS cells cultured in osteon-mimetic microtubes had drastically higher ALPase activity and calcium content, compared to laminated sheets. The data demonstrate that the 3D environment of the microtubes profoundly affects osteogenic differentiation of the BMS cells, compared to the 2D laminated sheets.

Release characteristics and osteogenic activity of recombinant human bone morphogenetic protein-2 grafted to novel self-assembled poly(lactide-co-glycolide fumarate) nanoparticles

Functionalized biodegradable nanoparticles (NPs) provide reactive groups and large surface area for grafting recombinant human bone morphogenetic protein-2 (rhBMP-2) to reduce protein diffusion and maintain sufficient concentration for recruitment and differentiation of osteoprogenitor cells. The objective of this work was to investigate release characteristics and osteogenic activity of rhBMP-2, grafted to biodegradable NPs based on succinimide-terminated poly(lactide fumarate) (PLAF-NHS) and poly(lactide-co-glycolide fumarate) (PLGF-NHS) macromers. The release of rhBMP-2 from the NPs, measured by enzyme-linked immunosorbent assay, was linear with time in the first two weeks, and 24.70+/-1.30% and 48.7+/-0.7% of the protein grafted to PLGF-NHS and PLAF-NHS NPs, respectively, was released in the enzymatically active conformation after complete degradation/erosion of the NPs. After 14 days of incubation with bone marrow stromal (BMS) cells, rhBMP-2 grafted to PLAF-NHS and PLGF-NHS NPs was as effective in inducing mineralization as the native rhBMP-2 that was directly added to the cell culture media. At any incubation time, rhBMP-2 grafted to PLAF had the highest expression of osteopontin (OP) and osteocalcin (OC), followed by rhBMP-2 grafted to PLGF and rhBMP-2 directly added to media. Higher OP and OC expression for BMP-gPLAF and BMP-gPLGF groups may be related to other factors in the cascade of osteogenesis, such as differentiation of BMS cells to the vasculogenic lineage and formation of a vascularized/mineralized matrix.

Applications of microscale technologies for regenerative dentistry

While widespread advances in tissue engineering have occurred over the past decade, many challenges remain in the context of tissue engineering and regeneration of the tooth. For example, although tooth development is the result of repeated temporal and spatial interactions between cells of ectoderm and mesoderm origin, most current tooth engineering systems cannot recreate such developmental processes. In this regard, microscale approaches that spatially pattern and support the development of different cell types in close proximity can be used to regulate the cellular microenvironment and, as such, are promising approaches for tooth development. Microscale technologies also present alternatives to conventional tissue engineering approaches in terms of scaffolds and the ability to direct stem cells. Furthermore, microscale techniques can be used to miniaturize many in vitro techniques and to facilitate high-throughput experimentation. In this review, we discuss the emerging microscale technologies for the in vitro evaluation of dental cells, dental tissue engineering, and tooth regeneration.