Evaluation of tooth analogs and type of restoration on the fracture resistance of post and core restored incisors

Influence of Root Post Materials and Aging on Fracture Strength and Marginal Gap Quality of Ceramic Crowns-An In Vitro Study

The design of and materials for prosthodontic abutments and posts have significant influences on the fracture resistance of restored teeth. This in vitro study compared the fracture strength and marginal quality of full-ceramic crowns as a function of the inserted root posts via simulation of a five-year period of use. Test specimens were prepared from 60 extracted maxillary incisors using titanium L9 (A), glass-fiber L9 (B), and glass-fiber L6 (C) root posts. The circular marginal gap behavior, linear loading capacity, and material fatigue after artificial aging were investigated. The marginal gap behavior and material fatigue were analyzed using electron microscopy. The linear loading capacity of the specimens was investigated using the Zwick Z005 universal testing machine. None of the tested root post materials showed statistically significant differences in marginal width values (p = 0.921), except in the case of marginal gap location. For Group A, there was a statistically significant difference from the labial to the distal (p = 0.012), mesial (p = 0.000), and palatinal (p = 0.005). Similarly, Group B showed a statistically significant difference from the labial to the distal (p = 0.003), mesial (p = 0.000), and palatinal (p = 0.003). Group C showed a statistically significant difference from the labial to the distal (p = 0.001) and mesial (p = 0.009). Linear load capacity reached mean values of 455.8-537.7 N, and micro-cracks occurred after artificial aging, predominantly in Groups B and C. Through the chosen experimental design, it was shown that the root post material and root post length had no influence on the fracture strength of the test teeth before or after artificial aging. However, the marginal gap location depends on the root post material and its length, which is wider mesially and distally and also tends to be greater palatinally than labially.

Methodology investigation: Impact of crown geometry, crown, abutment and antagonist material and thermal loading on the two-body wear of dental materials

OBJECTIVES

To investigate the impact of crown geometry, crown/abutment/antagonist material and thermal loading on the two-body wear of dental materials caused by chewing simulation.

MATERIALS AND METHODS

For the crown geometry, crowns (polymethylmethacrylate (PMMA), polyetheretherketone (PEEK) and silicate ceramic (SiO₂)) were milled with a flat, steep, or medium cusp inclination (CINC). For the crown/abutment material, crowns (PMMA, PEEK and SiO₂) were combined with PMMA, polymer-infiltrated-ceramic-network (PICN), cobalt-chrome alloy (CoCr) and natural teeth (ENAM) abutments. For the antagonist material, antagonists were fabricated from PICN, CAD/CAM resin composite (RECO), steatite (STEA), steel (STL) and ENAM and tested against flat specimens (substrates) made of veneering ceramic (VC). For thermal loading, the duration (30 s, 60 s, 120 s) and presence of temperature changes (37 °C versus 5 °C/55 °C) was varied. Material losses were determined by matching scanned specimens before and after aging (400,000 chewing cycles, 50 N, 1.3 Hz). Martens parameters were determined for the antagonists/substrates. Data were analyzed using Kolmogorov-Smirnov-test, Kruskal-Wallis H, Scheffé-Post-Hoc-tests, pairwise comparisons, Bonferroni correction, one-way ANOVA, Mann-Whitney-U and Spearman rho.

RESULTS

PMMA crowns presented the highest and PEEK the lowest material losses. Flat CINC showed the lowest material losses for PEEK and SiO₂ crowns. CoCr and ENAM abutments presented material losses in the same range. Antagonist and cumulative material losses for RECO and ENAM were similar. Thermal loading did not influence material losses.

SIGNIFICANCE

Crown geometry influences the crown and antagonists wear, with an increased cusp inclination entailing increased wear. For in vitro set-ups, CoCr abutments and RECO antagonists present valid alternatives to natural teeth. For polymers, in vitro chewing simulations may be performed at a constant temperature (37 °C).

Effect of supporting dies' mechanical properties on fracture behavior of monolithic zirconia molar crowns

The aim of this study was to investigate the effects of supporting dies with different mechanical properties on the fracture strengths and failure modes of monolithic zirconia crowns, and identify a suitable die material for testing high-strength ceramic restorations. Thirty six dies from teeth, porous titanium and composite-resin with 36 zirconia crowns were fabricated based on 3D model. Crowns were cemented, then underwent load-to-fracture testing. Fractographic analysis was performed with scanning electron microscopy, and finite element analysis was made. During loading, a high stress concentration zone formed near the loading point and on surface of die. Cracks generated on failure penetrated the crown and extended to die in 9 teeth group specimens, while composite-resin samples exhibited fracture of both crowns and dies. All dies remained intact in porous titanium group. Fracture mode was undistinguishable in all groups. It was concluded that porous titanium appears suitable as die material for dental restorations with high fracture strength.

Impact of high-speed sintering, layer thickness and artificial aging on the fracture load and two-body wear of zirconia crowns

OBJECTIVE

To investigate the impact of high-speed sintering, layer thickness and artificial aging in a chewing simulator on the fracture load (FL) and two-body wear (2BW) of 4Y-TZP crowns.

METHODS

4Y-TZP crowns (Ceramill Zolid HT+, Amann Girrbach AG) in three different layer thicknesses (0.5, 1.0, 1.5; N=192, n=64/group) were manufactured using CAD/CAM technology and sintered at 1580°C (high-speed sintering) or 1450°C (control group). Specimens were polished in two-steps and bonded to standardized CoCr abutments with Multilink Automix (Ivoclar Vivadent). 2BW after 6000 thermo- and 1,200,000 chewing-cycles employing enamel antagonists was determined using best fit machining. FL was tested before and after artificial aging. Univariate ANOVAs, post hoc Scheffé, unpaired t-, Kruskal-Wallis- and Mann-Whitney-U-test were computed (p<0.05).

RESULTS

High-speed sintering resulted in less 2BW of the zirconia than the control group (p=0.013). High-speed sintering (p=0.001-0.006) and an increase in layer thickness (p<0.001-0.012) resulted in higher FL values, while artificial aging led to a reduction of FL (p<0.001).

SIGNIFICANCE

As high-speed sintering resulted in less two-body wear of the zirconia and comparable or even higher fracture load results than the control group, this cost- and time efficient alternative presents promising mechanical results.

In vitro study of the fracture resistance of monolithic lithium disilicate, monolithic zirconia, and lithium disilicate pressed on zirconia for three-unit fixed dental prostheses

PURPOSE

The purpose of this study was to determine fracture resistance and failure modes of three-unit fixed dental prostheses (FDPs) made of lithium disilicate pressed on zirconia (LZ), monolithic lithium disilicate (ML), and monolithic zirconia (MZ).

MATERIALS AND METHODS

Co-Cr alloy three-unit metal FDPs model with maxillary first premolar and first molar abutments was fabricated. Three different FDPs groups, LZ, ML, and MZ, were prepared (n = 5 per group). The three-unit FDPs designs were identical for all specimens and cemented with resin cement on the prepared metal model. The region of pontic in FDPs was given 50,000 times of cyclic preloading at 2 Hz via dental chewing simulator and received a static load until fracture with universal testing machine fixed at 10°. The fracture resistance and mode of failure were recorded. Statistical analyses were performed using the Kruskal-Wallis test and Mann-Whitney U test with Bonferroni's correction (α=0.05/3=0.017).

RESULTS

A significant difference in fracture resistance was found between LZ (4943.87 ± 1243.70 N) and ML (2872.61 ± 658.78 N) groups, as well as between ML and MZ (4948.02 ± 974.51 N) groups (P<.05), but no significant difference was found between LZ and MZ groups (P>.05). With regard to fracture pattern, there were three cases of veneer chipping and two interfacial fractures in LZ group, and complete fracture was observed in all the specimens of ML and MZ groups.

CONCLUSION

Compared to monolithic lithium disilicate FDPs, monolithic zirconia FDPs and lithium disilicate glass ceramics pressed on zirconia-based FDPs showed superior fracture resistance while they manifested comparable fracture resistances.

Loading Standardization of Postendodontic Restorations In Vitro: Impact of Restorative Stage, Static Loading, and Dynamic Loading

Objective

The load capability of post-restored endodontically treated teeth (ETT) can be determined at different restorative stages. It was the aim of this study to compare the load capability of ETT at these stages.

Materials and Methods

Maxillary central incisors were divided into 4 groups (n=10) and endodontically treated. Specimens were restored with: (I) only glass fiber posts (GFP); (II) GFP and composite build-up with 2 mm ferrule; (III and IV) with additional adhesively luted all-ceramic crowns. Group (I) to (III) were statically loaded, and group (IV) was exposed to thermomechanical loading (TML) and subsequent static loading.

Results

The lowest median load level of 73 N was determined for group (I). The maximum median load value of 331 N was found for group (III). The comparison of Fmax [N] of group (I), (II) and (III) revealed significant differences between the groups (p&lt;0.001). The specimens of group (IV) failed at significantly lower load values (p&lt;0.005) as similarly restored specimens of group (III) which were only statically loaded. The stage of restoration and TML loading prior to static loading had a significant impact on fracture patterns (p=0.006).

Conclusion

Every additional restorative step torwards a final crown-restored ETT significantly increased the load capability. TML prior to load-to-fracture testing of the complete restorative complex, ie. post, core and crown, significantly decreased maximum load capability.

Load-bearing capacity of human incisor restored with various fiber-reinforced composite posts

OBJECTIVES

The aim of this study was to evaluate the load-bearing capacity and microstrain of incisors restored with posts of various kinds. Both prefabricated titanium posts and different fiber-reinforced composite posts were tested.

METHODS

The crowns of human incisors were cut and post preparation was carried out. The roots were divided into groups: (1) prefabricated serrated titanium posts, (2) prefabricated carbon fiber-reinforced composite posts, (3) individually formed glass fiber-reinforced composite posts with the canal full of fibers, and (4) individually formed "split" glass fiber-reinforced composite posts. The posts were cemented and composite crowns were made. Intact human incisors were used as reference. All roots were embedded in acrylic resin cylinders and stored at room temperature in water. Static load was applied under a loading angle of 45° using a universal testing machine. On half of the specimens microstrain was measured with strain gages and an acoustic emission analysis was carried out. Failure mode assessment was also made.

RESULTS

The group with titanium posts showed highest number of unfavorable failures compared to the groups with fiber-reinforced composite posts.

SIGNIFICANCE

With fiber-reinforced composite posts the failures may more often be favorable compared to titanium posts, which clinically means repairable failures.