Triclosan removal by adsorption using activated carbon derived from waste biomass: Isotherms and kinetic studies

Composites of sodium alginate based - Functional materials towards sustainable adsorption of benzene phenol derivatives - Bisphenol A/Triclosan

The present study evaluates the adsorption efficiency of low-cost carbonaceous adsorbents as fly ash (FA), saw dust biochar (SDB) (untreated and alkali - treated), live/dead pulverized white rot fungus Hypocrea lixii biomass encapsulated in sodium alginate (SA) against the commercially available activated carbon (AC) and graphene oxide (GO) SA beads for removal of benzene phenol derivatives - Bisphenol A (BPA)/triclosan (TCS). Amongst bi - and tri - composites SA beads, tri-composite beads comprising of untreated flyash - dead fungal biomass - sodium alginate (UFA - DB - SA) showed at par results with commercial composite beads. The tri - composite beads with point zero charge (Ppzc) of 6.2 was characterized using FTIR, XRD, surface area BET and SEM-EDX. The batch adsorption using tri - composite beads revealed removal of 93% BPA with adsorption capacity of 16.6 mg/g (pH 6) and 83.72% TCS with adsorption capacity of 14.23 mg/g (pH 5), respectively at 50 ppm initial concentration with 6 % adsorbent dose in 5 h. Freundlich isotherm favoring multilayered adsorption provided a better fit with r2 of 0.9674 for BPA and 0.9605 for TCS respectively. Intraparticle diffusion model showed adsorption of BPA/TCS molecules to follow pseudo - second order kinetics with boundary layer diffusion governed by first step of fast adsorption and intraparticle diffusion within pores by second slow adsorption step. Thermodynamic parameters (ΔH°, ΔS°, ΔG°) revealed adsorption process as exothermic, orderly and spontaneous. Methanol showed better desorbing efficiency leading to five cycles reusability. The phytotoxicity assay revealed increased germination rate of mung bean (Vigna radiata) seeds, sprinkled with post adsorbed treated water (0 h, 5 h and 7 h) initially spiked with 50 ppm BPA/TCS. Overall, UFA - DB - SA tri - composite beads provides a cost effective and eco - friendly matrix for effective removal of hydrophobic recalcitrant compounds.

Investigation of performance of potential adsorbents for emissions mitigation in a diesel generator

Globally, the release of greenhouse gases primarily carbon dioxide (CO2) emissions to our Earth's surface has climbed by  about 45% to its present atmospheric concentration rate of 420 parts per million (ppm) during the industrial era. An unprecedented rise in atmospheric CO2 concentration has been claimed to lead to significant factors such as global warming potential (GWP) and climate change effects.  An increase in atmospheric CO2 concentrations is  a  serious threat to the environment. Recent research efforts have focused on mitigating emissions from anthropogenic point sources. Adsorption-based post-combustion CO2 capture using solid adsorbents is the most effective and efficient method for mitigating gas adsorption in the exhaust system. In the current study, activated carbons are obtained from three potential biomass, namely, (i) coconut shell, (ii) rice husk, and (iii) eucalyptus wood, through a - single-stage activation method. The prepared activated carbon materials are analyzed using proximate and ultimate analyses. Further investigations are performed using different characterization techniques to ensure their adsorption efficiency. Adsorbents are packed one after the other in an in-house fabricated double adsorption chamber and coupled to the exhaust unit of a generator. Test experiments are conducted to examine adsorbents' capture efficiency in emissions mitigation. Adsorbents' adsorption parameters are evaluated in experimental investigations. At 2.5 bar and 50 °C, a maximum loading capacity of samples is achieved by 4.85 mmol/g, 4.58 mmol/g, and 5.96 mmol/g for coconut shell, rice husk, and eucalyptus wood adsorbents, respectively. With a post-combustion carbon adsorption chamber, CO2 and NO are captured about 40-64% and 38-58%, respectively, for all three adsorbents. The thermodynamic parameter of isosteric heat of adsorption value is below 40 kJ/mol, ensuring physisorption for all adsorbents.

Characterization and Performance of Peanut Shells in Caffeine and Triclosan Removal in Batch and Fixed-Bed Column Tests

Peanut shells' adsorption performance in caffeine and triclosan removal was studied. Peanut shells were analyzed for their chemical composition, morphology, and surface functional groups. Batch adsorption and fixed-bed column experiments were carried out with solutions containing 30 mg/L of caffeine and triclosan. The parameters examined included peanut shell particle size (120-150, 300-600, and 800-2000 µm), adsorbent dose (0.02-60 g/L), contact time (up to 180 min), bed height (4-8 cm), and hydraulic loading rate (2.0 and 4.0 m3/m2-day). After determining the optimal adsorption conditions, kinetics, isotherm, and breakthrough curve models were applied to analyze the experimental data. Peanut shells showed an irregular surface and consisted mainly of polysaccharides (around 70% lignin, cellulose, and hemicellulose), with a specific surface area of 1.7 m2/g and a pore volume of 0.005 cm3/g. The highest removal efficiencies for caffeine (85.6 ± 1.4%) and triclosan (89.3 ± 1.5%) were achieved using the smallest particles and 10.0 and 0.1 g/L doses over 180 and 45 min, respectively. Triclosan showed easier removal compared to caffeine due to its higher lipophilic character. The pseudo-second-order kinetics model provided the best fit with the experimental data, suggesting a chemisorption process between caffeine/triclosan and the adsorbent. Equilibrium data were well-described by the Sips model, with maximum adsorption capacities of 3.3 mg/g and 289.3 mg/g for caffeine and triclosan, respectively. In fixed-bed column adsorption tests, particle size significantly influenced efficiency and hydraulic behavior, with 120-150 µm particles exhibiting the highest adsorption capacity for caffeine (0.72 mg/g) and triclosan (143.44 mg/g), albeit with clogging issues. The experimental data also showed good agreement with the Bohart-Adams, Thomas, and Yoon-Nelson models. Therefore, the findings of this study highlight not only the effective capability of peanut shells to remove caffeine and triclosan but also their versatility as a promising option for water treatment and sanitation applications in different contexts.

First evidence of microplastics in the water and sediment of Surakarta city river basin, Indonesia

The main aim of this study was to assess the presence of microplastics in the water and sediments of the Surakarta city river basin in Indonesia. In order to accurately reflect the river basin, a deliberate selection process was employed to choose three separate sampling locations and twelve sampling points. The results of the study revealed that fragments and fibers were the primary types of microplastics seen in both water and sediment samples. Furthermore, a considerable percentage of microplastics, comprising 53.8 % of the total, had dimensions below 1 mm. Moreover, the prevailing hues identified in the water samples were blue and black, comprising 45.1 % of the overall composition. In contrast, same color categories accounted for 23.3 % of the microplastics found in the soil samples. The analysis of microplastic polymers was carried out utilizing ATR-FTIR spectroscopy, which yielded the identification of various types including polystyrene, silicone polymer, polyester, and polyamide.

Biological treatment of triclosan using a novel strain of Enterobacter cloacae and introducing naphthalene dioxygenase as an effective enzyme

In recent years, triclosan (TCS) has been widely used as an antibacterial agent in personal care products due to the spread of the Coronavirus. TSC is an emerging contaminant, and due to its stability and toxicity, it cannot be completely degraded through traditional wastewater treatment methods. In this study, a novel strain of Enterobacter cloacae was isolated and identified that can grow in high TCS concentrations. Also, we introduced naphthalene dioxygenase as an effective enzyme in TCS biodegradation, and its role during the removal process was investigated along with the laccase enzyme. The change of cell surface hydrophobicity during TCS removal revealed that a glycolipid biosurfactant called rhamnolipid was involved in TCS removal, leading to enhanced biodegradation of TCS. The independent variables, such as initial TCS concentration, pH, removal duration, and temperature, were optimized using the response surface method (RSM). As a result, the maximum TCS removal (97%) was detected at a pH value of 7 and a temperature of 32 °C after 9 days and 12 h of treatment. Gas chromatography-mass spectrometry (GC/MS) analysis showed five intermediate products and a newly proposed pathway for TCS degradation. Finally, the phytotoxicity experiment conducted on Cucumis sativus and Lens culinaris seeds demonstrated an increase in germination power and growth of stems and roots in comparison to untreated water. These results indicate that the final treated water was less toxic.

Nanomaterials for Removal of Phenolic Derivatives from Water Systems: Progress and Future Outlooks

Environmental pollution remains one of the most challenging problems facing society worldwide. Much of the problem has been caused by human activities and increased usage of various useful chemical agents that inadvertently find their way into the environment. Triclosan (TCS) and related phenolic compounds and derivatives belong to one class of such chemical agents. In this work, we provide a mini review of these emerging pollutants and an outlook on the state-of-the-art in nanostructured adsorbents and photocatalysts, especially nanostructured materials, that are being developed to address the problems associated with these environmental pollutants worldwide. Of note, the unique properties, structures, and compositions of mesoporous nanomaterials for the removal and decontamination of phenolic compounds and derivatives are discussed. These materials have a great ability to scavenge, adsorb, and even photocatalyze the decomposition of these compounds to mitigate/prevent their possible harmful effects on the environment. By designing and synthesizing them using silica and titania, which are easier to produce, effective adsorbents and photocatalysts that can mitigate the problems caused by TCS and its related phenolic derivatives in the environment could be fabricated. These topics, along with the authors' remarks, are also discussed in this review.

Preparation and characterization of low-cost activated carbon from Moringa oleifera chemically activated using ZnCl2 for the adsorption of bisphenol A

The use of agricultural by-products such as Moringa oleifera plants is one effort to support the reduction of environmental pollution. Activated carbon produces from agricultural wastes is relatively less expensive and can replace traditional methods such as renewable as well as nonrenewable materials such as petroleum residue and coal. In this study, the removal of bisphenol A from aqueous media was studied using activated carbon produced from M. oleifera pods and peels. A batch adsorption study was carried out by varying the parameters of the adsorption process. A maximum removal percentage of 95.46% was achieved at optimum conditions of 2.5 g L^-1 adsorbent dose, pH 7, 60 min contact time and 20 mg L^-1 initial concentration of BPA. The BET surface areas of MOP, MOP-AC and MOP-ACZ were found to be 12.60, 4.10 and 45.96 m²/g, respectively. The experimental data were analyzed by Langmuir, Freundlich and Temkin adsorption isotherm models. Equilibrium data fitted well with the Langmuir isotherm with a maximum monolayer adsorption capacity of 20.14 mg g^-1. The rates of adsorption were found to conform to the pseudo-second-order kinetics with a good correlation. The results indicate that the M. oleifera activated carbon could be employed as a low-cost alternative to commercial activated carbon in the removal of BPA from water.

Adsorption of rutin from olive mill wastewater using copolymeric hydrogels based on N-vinylimidazole: Kinetic, equilibrium, and thermodynamics assessments

Olive mill wastewater, also known as olive wastewater, contains biologically active components with various beneficial effects on health. The development of novel adsorbent materials for the recovery of these biologically active substances is important area of research. In this study, copolymeric hydrogels based on N-vinylimidazole (VIm), a new material that has never been used as an adsorbent in the separation of phenolic components, were synthesized. The hydrogels synthesized in this study is copolymer structures based on N-vinylimidazole (VIm) containing [2- (methacryloxy) ethyl] dimethylpentylammonium bromide (QDMAC5) in different moles. QDMAC5 was obtained by quaternization of 2- (dimethylamino) ethyl methacrylate (DMA) with 1-bromopentane (C5). The production of copolymer hydrogels was carried out by free radical solution polymerization. The syntheses were carried out only by changing the monomer composition so that the crosslinker ratio remained constant (1.2 mol%). The QDMAC5 content in the copolymers was 5, 10, 20, 30, and 50 mol%. So, the resulting structures were named PVQ-5%, PVQ-10%, PVQ-20%, PVQ-30%, and PVQ-50%, respectively. Functional group characterizations of hydrogels were made by Fourier Transform Infrared Spectrometry (FTIR). The surface of the hydrogels was analyzed by Scanning Electron Microscopy (SEM). Finally, thermogravimetric analyzes (TGA) were performed to investigate the thermal degradation behavior. The recovery of the rutin present in olive mill wastewater has been investigated as a model study. Kinetic data has been represented by the selected models (pseudo-first order, pseudo-second order, and intraparticle diffusion) convincingly (R² > 0.76), while the equilibrium findings have fitted well to Langmuir, Freundlich, and Temkin equations (R² > 0.77). Rutin adsorption process on N-vinylimidazole (VIm) based copolymeric hydrogels has been found as exothermic and spontaneous chemisorption process depending on the thermodynamic analysis.

An Ionic-Liquid-Imprinted Nanocomposite Adsorbent: Simulation, Kinetics and Thermodynamic Studies of Triclosan Endocrine Disturbing Water Contaminant Removal

The presence of triclosan in water is toxic to human beings, hazardous to the environment and creates side effects and problems because this is an endocrine-disturbing water pollutant. Therefore, there is a great need for the separation of this notorious water pollutant at an effective, economic and eco-friendly level. The interface sorption was achieved on synthesized ionic liquid-based nanocomposites. An N-methyl butyl imidazolium bromide ionic liquid copper oxide nanocomposite was prepared using green methods and characterized by using proper spectroscopic methods. The nanocomposite was used to remove triclosan in water with the best conditions of time 30 min, concentration 100 µg/L, pH 8.0, dose 1.0 g/L and temperature 25 °C, with 90.2 µg/g removal capacity. The results obeyed Langmuir, Temkin and D-Rs isotherms with a first-order kinetic and liquid-film-diffusion kinetic model. The positive entropy value was 0.47 kJ/mol K, while the negative value of enthalpy was −0.11 kJ/mol. The negative values of free energy were −53.18, −74.17 and −76.14 kJ/mol at 20, 25 and 30 °C. These values confirmed exothermic and spontaneous sorption of triclosan. The combined effects of 3D parameters were also discussed. The supramolecular model was developed by simulation and chemical studies and suggested electrovalent bonding between triclosan and N-methyl butyl imidazolium bromide ionic liquid. Finally, this method is assumed as valuable for the elimination of triclosan in water.

Investigation of two new low-cost adsorbents functionalized with magnetic nanoparticles for the efficient removal of triclosan and a synthetic mixture

Triclosan (TCS) is widely used in the production of antibacterial products, being often found in wastewater. Therefore, this study developed new materials via soybean hulls (SBH_F) and açaí seeds (AÇS_F) functionalization with iron oxide nanoparticles to be applied in the TCS adsorption. The characterization confirmed the functionalization of the materials. The adsorption results indicated that the equilibrium of the process occurred after 480 and 960 min for SBH_F and AÇS_F, respectively. The maximum adsorptive capacity values were 158.35 and 155.09 mg g^-1 for SBH_F and AÇS_F, respectively, at 318 K. The kinetic and isothermal data better fitted to the pseudo-second-order and Langmuir models. Thermodynamics indicated that the processes had an endothermic, spontaneous, and reversible character. The main adsorption mechanisms were H-bond and π-interactions. The pH and ionic strength studies indicated that the adsorption efficiency has not been reduced pronouncedly. The biosorbents reuse was effective for five cycles. In the synthetic mixture, the removal rate was satisfactory (92.53% and 57.02%, respectively for SBH_F and AÇS_F)_. These results demonstrate the biosorbents high potential for large-scale application.

Treatment of triclosan through enhanced microbial biodegradation

Triclosan (TCS) is extensively used in healthcare and personal care products as an antibacterial agent. Due to the persistent and toxic nature of TCS, it is not completely degraded in the biological wastewater treatment process. In this research work, identification of TCS degrading bacteria from municipal wastewater sludge and applying the same as bioaugmentation treatment for wastewater have been reported. Based on the 16S rRNA analysis of wastewater sludge, it was found that Providencia rettgeri MB-IIT strain was active and able to grow in higher TCS concentration. The identified bacterial strain was able to use TCS as carbon and energy source for its growth. The biodegradation experiment was optimized for the operational parameters viz. pH (5-10), inoculum size (1-5% (v/v)) and different initial concentration (2, 5, and 10 mg/L) of TCS. During the TCS degradation process, manganese peroxidase (MnP) and laccase (LAC) enzyme activity and specific growth rate of P. rettgeri strain were maximum at pH=7% and 2% (v/v) inoculum size, resulting in 98% of TCS removal efficiency. A total of six intermediate products were identified from the Liquid chromatography-high-resolution mass spectrometry (LC-HRMS) analysis, and the two mechanisms responsible for the degradation of TCS have been elucidated. The study highlights that P. rettgeri MB-IIT strain could be advantageously used to degrade triclosan present in the wastewater.

Differential roles of ash in sorption of triclosan to wood-derived biochars produced at different temperatures

Biochar is composed of carbonaceous and inorganic (ash) fractions. The structural properties of carbonaceous fractions and the composition of ash in biochar are both variable with pyrolysis temperature. However, it is unknown whether ash may play different roles in sorption of organic compounds to the carbonaceous fraction of biochars produced at different temperatures. Hence, in this study, the pristine biochars produced at 300-900°C and their corresponding deashed biochars were investigated, and the combined roles of carbonaceous fraction and ash in sorption of triclosan were compared. The results showed that the biochars produced at 300-400°C had high content of uncarbonized organic structure with dominating partition effect. The combination of uncarbonized organic structure and ash had comparable or even higher sorption coefficient (K_D ) for triclosan at low concentration compared with a single uncarbonized organic structure. However, for the biochars produced at 600-900°C, which were mainly composed of carbonized or graphitized carbon structure, ash had significant effect on triclosan sorption by reducing surface adsorption and pore filling effect. The combination of carbonaceous fraction and ash decreased K_D values for triclosan at any tested concentrations. In addition, the results of pH effect on sorption indicated that ash possibly decreased the electrostatic repulsion of deprotonated phenolic hydroxyl between biochars and triclosan. Accordingly, it will be more valuable to design biochars for pollutant sorption from the perspective of combined role of carbonaceous fraction and ash rather than a single role of carbonaceous fraction.

Simultaneous removal of mixed contaminants triclosan and copper by green synthesized bimetallic iron/nickel nanoparticles

The mixed contamination of environmental matrices by antibacterial agents and heavy metals has attracted much attention worldwide due to the complex nature of their environmental interactions and their potential toxicity. In this work, green synthesized bimetallic iron/nickel nanoparticles (Fe/Ni NPs) was used to simultaneously remove triclosan (TCS) and copper (Cu (II)) under optimal experimental conditions with removal efficiencies of 75.8 and 44.1% respectively. However, in a mixed contaminant system the removal efficiencies of TCS and Cu (II) were lower than when TCS (85.8%) and Cu (II) (52.5%) were removed separately, suggesting that there was competitive relationship between the two contaminants and Fe/Ni NPs used for remediation. SEM-EDS, XRD and FTIR all indicated that both TCS and Cu (II) were adsorbed onto Fe/Ni NPs. Furthermore, while XPS showed that Cu (II) was reduced to Cu⁰, GC-MS analysis showed that TCS also underwent degradation with 2,7/2,8-Cl₂DD as the major intermediate. The adsorption of both contaminants fit well a pseudo second order kinetic model (R²>0.998) and the Freundlich isotherm (R²>0.905). Whereas the reduction kinetics obeyed a pseudo first order model. Thus, overall the removal of TCS and Cu (II) involved a combination of both adsorption and reduction. Finally, a removal mechanism for triclosan and Cu (II) was proposed. Overall, Fe/Ni NPs have the potential to practically coinstantaneously remove both TCS and Cu (II) from aqueous solution under a wide range of conditions.