Fabrication and photocatalytic activity of LaFeO 3 ribbon‐like nanofibers

Insight of the State for Deliberately Introduced A-Site Defect in Nanofibrous LaFeO3 for Boosting Artificial Photosynthesis of CH3OH

Perovskite-type LaFeO3 is regarded as a potentially efficient visible-light photocatalyst owing to its narrow bandgap energy and unique photovoltaic properties. However, the insufficient active sites and the unsatisfactory utilization of photogenerated carriers severely restrict the realistic application of pure LaFeO3. Herein, we fabricated a series of LaxFeO3-δ nanofibers (x = 1.0, 0.95, 0.9, 0.85, 0.8) with an A-site defect via sol-gel combined with the electrospinning technique. Wherein, the nonstoichiometric La0.9FeO3-δ possessed the highest CH3OH yield of 5.30 μmol·g-1·h-1 with good chemical stability. A series of advanced characterizations were applied to investigate the physicochemical properties and charge-carrier behaviors of the samples. The results illustrated that the one-dimensional (1D) nanostructures combined with the appropriate concentration of vacancy defects on the surface contributed to the radial migration of photogenerated carriers, inhibited the recombination of carriers, and provided more CO2 adsorption-activation sites. Furthermore, density functional theory (DFT) calculations were employed to reveal the influence mechanism of vacancy defects on LaFeO3. This work provides a strategy to enhance the performance of photocatalytic CO2 reduction by modulating the induced oxygen vacancies caused by the A-site defect in perovskite oxides.

B-site metal modulation of phosphate adsorption properties and mechanism of LaBO3 (B = Fe, Al and Mn) perovskites

La-based adsorbents are widely used for controlling phosphate concentration in water bodies. In order to explore the effect of different B-site metals regulating La-based perovskites on phosphate adsorption, three La-based perovskites (LaBO₃, B = Fe, Al, and Mn) were prepared using the citric acid sol-gel method. Adsorption experiments showed that LaFeO₃ exhibited the highest adsorption capacity for phosphate, which was 2.7 and 5 times higher than those of LaAlO₃ and LaMnO₃, respectively. The characterization results demonstrated that LaFeO₃ has dispersed particles exhibiting larger pore size and more pores than LaAlO₃ and LaMnO₃. Spectroscopy analysis and density functional theory calculation results showed that different B-positions cause a change in the type of perovskite crystals. Among them, the differences between lattice oxygen consumption ratio, zeta potential and adsorption energy are the main reasons for the differences in adsorption capacity. In addition, the adsorption of phosphate by La-based perovskites were well fitted with Langmuir isotherm and pursues the pseudo-second-order kinetic models. The maximum adsorption capacities were 33.51, 12.31 and 6.61 mg/g for LaFeO₃, LaAlO₃ and LaMnO₃, respectively. The adsorption mechanism was mainly based on inner-sphere complexation and electrostatic attraction. This study provides an explanation for the influence of different B sites on phosphate adsorption by perovskite.

Green and Efficient Al-Doped LaFexAl1-xO3 Perovskite Oxide for Enhanced Phosphate Adsorption with Creation of Oxygen Vacancies

La-based metal oxide materials are environmentally friendly and show promise for phosphate adsorption. A series of Al-doped perovskite oxides, such as LaFe_xAl_1-xO₃, were prepared using a facile citric acid-assisted sol-gel method. The characterization results demonstrated that with optimized Al doping, there was a significant increase in the specific surface area and increased defect content of perovskite oxide LaFe_xAl_1-xO₃. Adsorption experiments showed that the performance of phosphate removal by LaFe_xAl_1-xO₃ was largely enhanced due to the improved adsorption capacity, which is maximum eight times higher compared with control perovskites prepared under neutral conditions. The mass transfer rate for adsorption was considerably boosted with phosphate removal within the initial 15 min. Spectroscopy analysis and density functional theory calculation results showed that the process of phosphate removal by the Al-doped perovskite oxides LaFe_xAl_1-xO₃ involved electrostatic interactions, an inner-sphere complex, and surface oxygen vacancies, among which the creation of oxygen vacancies caused by the Al doping was the predominant mechanism for reducing the bonding barrier during adsorption and generating adsorption sites. The results enable the development of a green and efficient perovskite adsorbent with a La-based perovskite material for phosphorus removal.

Fissure Grouting Mechanism Accounting for the Time-Dependent Viscosity of Silica Sol

Subject to the complex hydrogeological environment where underground engineering is located, the grouting prevention and control of microfissure water ingress are increasingly strict. Silica sol grout has been increasingly used in field tests because of its fine particles and good injectability. Therefore, it is necessary to examine the time-dependent viscosity of silica sol grout and clarify its diffusion law in a rock fissure. In this study, the time dependence of the viscosity of silica sol grout was studied, and then the grout viscosity was subdivided into a slow growth period, accelerated growth period, and rapid curing period according to the growth rate. The effects of the concentration of colloidal silica suspension, the concentration of accelerant, and the mixing volume ratio of the two on the growth of the slurry viscosity were studied. A parameter λ was introduced to comprehensively characterize the influence of the three factors on the rheological properties of the slurry. The relationship between the gel induction time and λ and the accelerating growth stage of the slurry gel was obtained by data fitting. The time-dependent equation of the silica sol solution was established. The difference in the grouting diffusion law between silica sol grout and cement-sodium silicate grout (C-S grout) is compared and analyzed by a stepwise calculation method under two grouting modes (constant-pressure grouting and constant-rate grouting). The results show that under the condition of constant-pressure grouting, the silica sol grout migrates and diffuses continuously for a long time, while the C-S grout is close to the final diffusion form at 15-20 s, and the maximum diffusion distance is much smaller than that of silica sol grout. Under the condition of constant-rate grouting, the grouting pressure driving C-S grout increases sharply with time. Compared with C-S grout, silica sol grout has the obvious advantages of a longer effective diffusion time and lower energy consumption. The research results have certain theoretical significance and reference value for the engineering design of silica sol grouting.