Model for the evaluation of root wear by histometric analysis

Influence of Different Proportions of External Irrigation During the Er,Cr:YSGG Laser Irradiation on Wear and Roughness of Root Surface

INTRODUCTION

The aim of this study was to evaluate the influence of different levels of external irrigation during irradiation with an erbium, chromium: yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser on the roughness and wear of dental tissue during scaling procedures.

METHODS

Twenty-Five uniradicular bovine teeth had the proximal surfaces planed and divided into 3 regions: upper, middle and lower. The upper region was treated with hand instruments, the middle region was not treated and served as a control, and the lower region was treated by the Er,Cr:YSGG laser. The teeth were randomly divided into five groups according to the different proportions of external irrigation used during the laser irradiation: G1: 10%; G2: 20%; G3: 30%; G4: 40% and G5: 50%. The samples were analyzed for roughness and wear on the root surface irradiated with the laser.

RESULTS

There were no differences in the surface roughness and wear parameters between the groups irradiated with the laser, but the laser irradiation produced a rougher surface of the dentin than treatment with hand scaling.

CONCLUSION

Changes in the external irrigation level did not influence the wear and roughness of root surfaces treated with an Er,Cr:YSGG laser.

A microscopic analysis of the effects of root surface scaling with different power parameters of Er,Cr:YSGG laser

The aim of this study was to evaluate the effects of different power parameters of an Erbium, Cromium: Yttrium, Scandium, Gallium, Garnet laser (Er,Cr:YSGG laser) on the morphology, attachment of blood components (ABC), roughness, and wear on irradiated root surfaces. Sixty-five incisive bovine teeth were used in this study, 35 of which were used for the analysis of root surface morphology and ABC. The remaining 30 teeth were used for roughness and root wear analysis. The samples were randomly allocated into seven groups: G1: Er,Cr:YSGG laser, 0.5 W; G2: Er,Cr:YSGG laser, 1.0 W; G3: Er,Cr:YSGG laser, 1.5 W; G4: Er,Cr:YSGG laser, 2.0 W; G5: Er,Cr:YSGG laser, 2.5 W; G6: Er,Cr:YSGG laser, 3.0 W; G7: scaling and root planning (SRP) with manual curettes. The root surfaces irradiated by Er,Cr:YSGG at 1.0 W and scaling with manual curettes presented the highest degrees of ABC. The samples irradiated by the Er,Cr:YSGG laser were rougher than the samples treated by the manual curette, and increasing the laser power parameters caused more root wear and greater roughness on the root surface. The Er,Cr:YSGG laser is safe to use for periodontal treatment, but it is not appropriate to use irradiation greater than 1.0 W for this purpose.

The effect of the angle of instrumentation of the Piezoelectric Ultrasonic Scaler on root surfaces

OBJECTIVES

To evaluate the influence of variations in the working angle of the piezoelectric ultrasonic scaler (PUS) on root surfaces.

MATERIAL AND METHODS

Fifty-five uniradicular bovine teeth were used, of which 25 teeth were used for the analysis of the roughness and root wear, while the remaining 30 teeth were used for the analysis of morphology (MRS) and the attachment of blood components (ABC). The teeth were randomly divided into five groups according to the type of treatment (G1-G5: piezoelectric ultrasonic scaler; G6: manual curette) and to the PUS working angle applied (G1: 0°; G2: 30°; G3: 45°; G4: 60°; G5: 90°). For statistical analysis, the data describing the MRS and ABC were analysed by the Kruskal-Wallis and Dunn's tests, and the data describing the roughness and tooth wear were analysed by anova and Tukey's tests at the significance level of 5%.

RESULTS

Manual curette (MC) promoted a smoother root surface than the application of the PUS. The PUS used at the angles of 30° and 45° resulted in a high level of ABC that was comparable to that obtained by MC. Additionally, the group in which the PUS was applied at an angle of 45° exhibited less tooth wear than the other groups.

CONCLUSIONS

Changes in the working angle of the PUS influenced the characteristics of root surfaces after instrumentation.